Home › Drivetrain › PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for 4WD)
RM27M0U _52 Drivetrain _049149 PROPELLER SHAFT _0234383 PROPELLER SHAFT ASSEMBLY(for 4WD) A

PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for 4WD)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

C160090E02
2.286,1.456 2.505,1.608 0.219,0.152 10 *a 2.01,0.721 2.331,1.399 false 2.331,1.399 1.886,0.701 false

a.

Place matchmarks on the propeller shaft yoke and universal joint yoke.

Text in Illustration
*a Matchmark


b.
C185093

Remove the grease fitting from the spider bearing.


c.
C160091

Using a brass bar and hammer, slightly tap in the 4 spider bearings.


d.

Using needle-nose pliers, remove the 4 snap rings from the grooves.


e.
C184732

Using a screwdriver, remove the 4 slingers of the spider bearing.


f.

Clamp the propeller shaft in a vise between aluminum plates.


g.
C293088E02
2.406,1.698 2.26,1.698 false 2.26,1.698 2.26,2.01 false 2.635,1.24 3.052,1.24 false 3.052,1.24 3.052,1.938 false 2.708,1.302 3.052,1.302 false 1.688,3.844 1.688,4.031 false 1.052,1.75 0.542,1.75 false 0.875,1.542 0.75,1.542 false 0.75,1.542 0.75,1.938 false 0.75,1.938 1.031,1.938 false 0.26,1.667 0.594,1.833 0.333,0.167 10 false SST 1.615,4 1.844,4.156 0.229,0.156 10 false *a 1.573,1.229 1.802,1.385 0.229,0.156 10 false *d 2.188,0.458 2.417,0.615 0.229,0.156 10 false *c 2.208,2.021 2.438,2.177 0.229,0.156 10 false *b 2.927,1.938 3.26,2.104 0.333,0.167 10 false SST

Using SST, press in spider bearing B until spider bearing A can be clamped in a vise.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09957-04010, 09958-04011)
09950-60010  (09951-00290)
09955-04100  

Text in Illustration
*a Spider Bearing A
*b Spider Bearing B
*c Turn
*d Hold

HINT:

Make sure the claws of SST are securely attached to the universal joint yoke.



h.

Clamp the protruding universal joint spider bearing in a vise.


i.
C183192E02
2.025,0.124 2.221,0.278 0.197,0.154 10 *a 1.986,0.208 1.742,0.208 false 1.742,0.208 1.658,0.69 false

Using a brass bar and hammer, tap the universal joint yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

NOTICE:

Do not tap the intermediate shaft tube.


HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



j.

Disconnect the intermediate shaft from the propeller shaft.


k.
C293089E02
2.438,1.021 2.948,1.021 false 2.469,1.219 2.938,1.219 false 2.948,1.021 2.948,1.875 false 2.302,1.698 2.302,1.958 false 0.438,1.604 0.573,1.604 false 0.5,1.604 0.5,2.052 false 0.5,2.052 0.781,2.052 false 0.813,1.885 0.5,1.885 false 0.333,2.427 0.333,2.76 false 2.24,1.979 2.438,2.146 0.198,0.167 10 false *a 1.615,1.323 1.813,1.49 0.198,0.167 10 false *c 1.781,0.333 1.979,0.5 0.198,0.167 10 false *b 2.823,1.917 3.167,2.073 0.344,0.156 10 false SST 0.177,1.542 0.49,1.698 0.313,0.156 10 false SST 0.208,2.792 0.521,2.948 0.313,0.156 10 false SST

Using SST, pull out the universal joint spider bearing from the propeller shaft yoke.

SST
09331-60010  
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
09955-04100  

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the propeller shaft yoke.



l.

Clamp the protruding universal joint spider bearing in a vise.


m.
C184804E02
2.181,0.05 2.375,0.209 0.194,0.159 10 *a 2.136,0.133 1.874,0.133 false 1.874,0.133 1.874,0.477 false

Using a brass bar and hammer, tap the propeller shaft yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

NOTICE:

Do not tap the propeller shaft tube.


HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



n.

Remove the spider from the propeller shaft.


Hide 37230 2.REMOVE NO. 1 CENTER SUPPORT BEARING ASSEMBLY

a.

Fix the center support bearing in a vise.


b.

Using a chisel and hammer, loosen the staked part of the lock nut. Then remove the lock nut.


c.
C158515E02
0.704,0.479 0.867,0.626 0.163,0.147 10 *a 1.73,1.094 0.921,0.578 false 0.921,0.578 1.73,1.007 false

Place matchmarks on the joint yoke and shaft.

Text in Illustration
*a Matchmark


d.

Using a brass bar and hammer, tap the end of the intermediate shaft to remove the joint yoke, washer and center support bearing from the intermediate shaft.


Hide 3.REMOVE REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

HINT:

Use the same removal procedure for both the front and rear propeller shaft universal joint spider bearings.


a.
C158459E03
1.497,1.778 1.702,1.934 0.206,0.156 10 *a 1.922,1.001 1.603,1.771 false 1.603,1.771 1.73,0.985 false

Place matchmarks on the flange yoke and shaft.

Text in Illustration
*a Matchmark


b.

Remove the grease fitting from the spider bearing.


c.
C158510

Using a brass bar and hammer, slightly tap in the 4 spider bearings.


d.
G038875

Using needle-nose pliers, remove the 4 snap rings from the grooves.


e.
C184732

Using a screwdriver, remove the 4 slingers of the spider bearing.


f.

Clamp the shaft in a vise between aluminum plates.


g.
C293090E02
1.073,2.219 1.802,2.573 false 1.802,2.573 0.833,2.573 false 0.833,2.865 1.677,3.125 false 2.354,0.906 2.354,0.792 false 2.354,0.792 2.885,0.792 false 2.542,1.031 2.542,0.792 false 1.719,3.063 1.927,3.229 0.208,0.167 10 false *a 1.875,2.479 2.188,2.646 0.313,0.167 10 false SST 0.656,0.667 0.865,0.833 0.208,0.167 10 false *b 0.26,1.094 0.469,1.26 0.208,0.167 10 false *c 2.938,0.708 3.25,0.875 0.313,0.167 10 false SST

Using SST, pull out the universal joint spider bearing from the shaft.

SST
09331-60010  
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
09955-04100  

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the shaft's universal joint yoke.



h.

Clamp the protruding universal joint spider bearing in a vise.


i.
C179267E02
2.238,2.878 2.430,3.042 0.192,0.164 10 *a 2.211,2.891 1.832,2.497 false

Using a brass bar and hammer, tap the shaft yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

NOTICE:

Do not tap the shaft tube.


HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



j.
C293091E02
0.969,2.573 1.771,2.708 false 1.771,2.708 1.219,2.167 false 0.948,2.896 1.729,3.073 false 2.885,0.823 2.615,0.823 false 2.615,0.823 2.615,0.99 false 2.792,0.823 2.792,1.135 false 1.802,2.719 2.104,2.865 0.302,0.146 10 false SST 1.76,3.01 1.938,3.177 0.177,0.167 10 false *a 1.76,3.01 1.938,3.177 0.177,0.167 10 false *a 0.76,0.76 0.938,0.927 0.177,0.167 10 false *b 0.167,1.219 0.344,1.385 0.177,0.167 10 false *c 2.938,0.74 3.26,0.896 0.323,0.156 10 false SST

Using SST, pull out the universal joint spider bearing from the flange yoke.

SST
09331-60010  
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-04010, 09958-04011)
09955-04100  

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the flange yoke.



k.

Clamp the protruding universal joint spider bearing in a vise.


l.
C179271E03
1.521,2.458 1.104,2.656 false 0.927,2.604 1.115,2.781 0.188,0.177 10 false *a

Using a brass bar and hammer, tap the flange yoke to remove the universal joint spider bearing.

Text in Illustration
*a Hammering Point

HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.



m.

Remove the spider from the flange yoke.