Home › Drivetrain › PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for 4WD)
RM27M0U _52 Drivetrain _049149 PROPELLER SHAFT _0234383 PROPELLER SHAFT ASSEMBLY(for 4WD) A

PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for 4WD)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

HINT:

Use the same installation procedure for both the front and rear propeller shaft universal joint spider bearings.


a.
C134387

Apply MP grease to a new spider and 4 new bearings.

NOTICE:

Be careful not to apply too much grease.



b.

Measure dimension A between the snap ring grooves.


c.
C160099E01
1.243,1 1.372,1.143 0.128,0.142 10 A 1.676,1.002 1.805,1.155 0.129,0.154 10 B

Install the 4 spider bearings to the spider journal portions, and then measure dimension B of the universal joint.

NOTICE:

When measuring dimension B, fix the spider and spider bearings in a vise and hold them firmly together.



d.

w/o Grease Fitting Spider Bearing:

i.
G038874

Select snap rings to make dimensions A and B the same.

Snap ring type for steel yoke:
Color Thickness
Purple 1.46 mm (0.0574 in.)
Black 1.49 mm (0.0586 in.)
Copper 1.51 mm (0.0594 in.)
White 1.56 mm (0.0614 in.)
Yellow 1.59 mm (0.0625 in.)
Blue 1.64 mm (0.0646 in.)


Snap ring type for aluminum yoke:
Color Thickness
Black 1.52 mm (0.0598 in.)
Black 1.54 mm (0.0606 in.)
Black 1.57 mm (0.0618 in.)
Black 1.62 mm (0.0638 in.)


NOTICE:
·

Use new snap rings.

·

If possible, use snap rings of the same thickness for both sides.





e.

w/ Grease Fitting Spider Bearing:

i.
C166540

Select snap rings to make dimensions A and B the same.

Snap ring type:
Color Thickness
Black 1.49 mm (0.0586 in.)
Copper 1.51 mm (0.0594 in.)
White 1.56 mm (0.0614 in.)
Yellow 1.59 mm (0.0625 in.)


NOTICE:
·

Use new snap rings.

·

If possible, use snap rings of the same thickness for both sides.





f.

Temporarily install the spider and 2 universal joint spider bearings into the flange yoke.


g.
C293092E02
2.719,2.01 3.021,2.01 false 2.573,1.49 2.906,1.49 false 2.656,1.604 2.75,1.604 false 2.75,1.604 2.75,1.49 false 0.948,1.729 0.583,1.729 false 0.583,1.729 0.583,3 false 0.583,3 1,3 false 1,2.583 0.583,2.583 false 1.01,2.177 0.458,2.177 false 3.052,1.927 3.24,2.104 0.188,0.177 10 false *a 0.177,1.146 0.396,1.323 0.219,0.177 10 false *c 0.594,0.302 0.813,0.479 0.219,0.177 10 false *b 2.948,1.406 3.271,1.563 0.323,0.156 10 false SST 0.167,2.104 0.49,2.26 0.323,0.156 10 false SST

Using SST, press the universal joint spider bearing into the flange yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Confirm that the universal joint spider moves smoothly while pressing in the bearing.



h.
C179275

Using needle-nose pliers, install the previously selected snap ring into the groove of the yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



i.

Temporarily install the spider and 2 universal joint spider bearings into the shaft yoke.


j.
C293093E03
0.51,2.594 0.51,2.813 false 2.51,2.281 2.875,2.281 false 2.594,2.396 2.729,2.396 false 2.729,2.396 2.729,2.281 false 2.625,2.781 2.938,2.781 false 2.156,1.448 2.854,1.448 false 2.167,1.219 2.979,1.219 false 2.188,1 2.854,1 false 2.854,1.448 2.854,0.844 false 2.854,0.844 2.271,0.844 false 0.375,2.854 0.708,3.01 0.333,0.156 10 false SST 2.917,2.198 3.229,2.354 0.313,0.156 10 false SST 2.979,2.688 3.177,2.854 0.198,0.167 10 false *a 0.646,0.5 0.844,0.667 0.198,0.167 10 false *b 0.24,1.135 0.438,1.302 0.198,0.167 10 false *c 3.021,1.135 3.354,1.292 0.333,0.156 10 false SST

Using SST, press the universal joint spider bearing into the shaft yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:
·

Position SST (09336-16010) so that the cutout faces the shaft tube.

·

Confirm that the universal joint spider moves smoothly while pressing in the bearing.




k.
U152374

Using needle-nose pliers, install the previously selected snap ring into the groove on the shaft yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



Hide 37230 2.INSTALL NO. 1 CENTER SUPPORT BEARING ASSEMBLY

a.

Coat the splines of the intermediate shaft with MP grease.


b.
C293097

Install the center support bearing to the intermediate shaft.

Text in Illustration
V100135

Front


c.
C158515E02
0.704,0.479 0.867,0.626 0.163,0.147 10 *a 1.73,1.094 0.921,0.578 false 0.921,0.578 1.73,1.007 false

Align the matchmarks on the joint yoke and intermediate shaft.

Text in Illustration
*a Matchmark


d.

Install the washer.


e.

Clamp the yoke in a vise, and press the bearing into position by installing a new lock nut.

Torque:
128 N*m (1300 kgf*cm, 94 ft.*lbf)


f.

Loosen the lock nut.


g.

Tighten the lock nut again.

Torque:
128 N*m (1300 kgf*cm, 94 ft.*lbf)


h.

Using a chisel and hammer, stake the lock nut.


Hide 3.INSTALL REAR PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

a.
C134387

Apply MP grease to a new spider and 4 new bearings.

NOTICE:

Be careful not to apply too much grease.



b.
C160099E01
1.243,1 1.372,1.143 0.128,0.142 10 A 1.676,1.002 1.805,1.155 0.129,0.154 10 B

Measure dimension A between the snap ring grooves.


c.

Install the 4 spider bearings to the spider journal portions, and then measure dimension B of the universal joint.

NOTICE:

When measuring dimension B, fix the spider and spider bearings in a vise and hold them firmly together.



d.

w/o Grease Fitting Spider Bearing:

i.
G038874

Select snap rings to make dimensions A and B the same.

Snap ring type for steel yoke:
Color Thickness
Purple 1.46 mm (0.0574 in.)
Black 1.49 mm (0.0586 in.)
Copper 1.51 mm (0.0594 in.)
White 1.56 mm (0.0614 in.)
Yellow 1.59 mm (0.0625 in.)
Blue 1.64 mm (0.0646 in.)


Snap ring type for aluminum yoke:
Color Thickness
Black 1.52 mm (0.0598 in.)
Black 1.54 mm (0.0606 in.)
Black 1.57 mm (0.0618 in.)
Black 1.62 mm (0.0638 in.)


NOTICE:
·

Use new snap rings.

·

If possible, use snap rings of the same thickness for both sides.





e.
C166540

w/ Grease Fitting Spider Bearing:

i.

Select snap rings to make dimensions A and B the same.

Snap ring type:
Color Thickness
Black 1.49 mm (0.0586 in.)
Copper 1.51 mm (0.0594 in.)
White 1.56 mm (0.0614 in.)
Yellow 1.59 mm (0.0625 in.)


NOTICE:
·

Use new snap rings.

·

If possible, use snap rings of the same thickness for both sides.





f.

Temporarily install the universal joint spider and 2 universal joint spider bearings into the propeller shaft yoke.


g.
C293094E02
2.688,1.833 3.021,1.833 false 2.573,1.323 2.885,1.323 false 2.656,1.438 2.802,1.438 false 2.792,1.438 2.792,1.323 false 0.875,2.844 0.625,2.844 false 0.625,2.844 0.625,2.042 false 0.833,2.531 0.625,2.531 false 0.854,2.042 0.396,2.042 false 3.073,1.75 3.26,1.927 0.188,0.177 10 false *a 0.083,1.385 0.292,1.563 0.208,0.177 10 false *c 0.625,0.385 0.833,0.563 0.208,0.177 10 false *b 2.938,1.24 3.26,1.417 0.323,0.177 10 false SST 0.104,1.958 0.427,2.135 0.323,0.177 10 false SST

Using SST, press the universal joint spider bearing into the propeller shaft yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold

NOTICE:

Confirm that the universal joint spider moves smoothly while pressing in the bearing.



h.
G038875

Using needle-nose pliers, install the previously selected snap ring into the groove of the yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



i.

Align the matchmarks on the propeller shaft yoke and universal joint yoke, and temporarily install the spider and 2 universal joint spider bearings into the universal joint yoke.


j.
C293095E02
2.74,2.208 2.99,2.208 false 2.635,1.771 2.927,1.771 false 2.708,1.854 2.833,1.854 false 2.833,1.854 2.833,1.771 false 1.104,2.813 0.469,2.813 false 1.104,3.271 0.729,3.271 false 0.729,3.271 0.729,2.813 false 1.021,3.083 0.729,3.083 false 1.323,1.854 1.323,1.583 false 1.323,1.583 0.729,1.583 false 1.115,1.75 1.115,1.583 false 3.021,2.125 3.219,2.292 0.198,0.167 10 false *a 0.115,2.135 0.313,2.302 0.198,0.167 10 false *c 0.51,1.063 0.708,1.229 0.198,0.167 10 false *b 2.958,1.708 3.271,1.865 0.313,0.156 10 false SST 0.177,2.74 0.49,2.896 0.313,0.156 10 false SST 0.448,1.51 0.76,1.667 0.313,0.156 10 false SST

Using SST, press the universal joint spider bearing into the universal joint yoke until the groove can be seen.

SST
09336-16010  
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04020, 09955-04051, 09957-04010)
09950-60010  (09951-00290)

Text in Illustration
*a Spider Bearing
*b Turn
*c Hold


k.

Using needle-nose pliers, install the previously selected snap ring into the groove on the universal joint yoke.

HINT:

Use the same installation procedure for the universal joint spider bearing on the opposite side.



Hide 4.INSTALL PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

a.
C158513

Check the spider bearings for wear and damage.


b.

Measure each spider bearing's axial play by turning the yoke while holding the shaft tightly.

Maximum bearing axial play:

0.05 mm (0.00197 in.)