Home › Drivetrain › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 4WD)
RM27M0U _52 Drivetrain _049150 DRIVE SHAFT _0234386 FRONT DRIVE SHAFT ASSEMBLY(for 4WD) A

DRIVE SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 4WD)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Do not allow brake fluid, front differential oil, gasoline, or battery fluid to contact the drive shaft boots, as they may damage the boots.


PROCEDURE

Hide 1.INSTALL DUST SEAL

a.
C115634E01
0.175,0.677 0.484,0.866 0.309,0.188 10 SST 1.266,1.685 0.536,0.889 false

Using SST and a press, press in a new dust seal to the outboard joint shaft.

SST
09950-00020  

NOTICE:

Be careful not to damage the dust seal.



Hide 41336E 2.INSTALL FRONT DRIVE SHAFT DUST COVER LH

a.
C115635E02
1.313,0.771 1.781,0.219 false 0.51,1.875 0.74,1.552 false 1.823,0.094 2.604,0.281 0.781,0.188 10 false Steel Plate 0.198,1.844 0.51,2.042 0.313,0.198 10 false SST

Using SST, a steel plate and press, press in a new dust cover.

SST
09316-20011  

NOTICE:

Be careful not to damage the dust cover.



Hide 3.INSTALL OUTBOARD JOINT BOOT

a.
C115636E01
2.415,0.362 3.127,0.592 0.711,0.230 10 Vinyl Tape 2.014,0.989 2.392,0.563 false

Place 2 new boot clamps on the boot.

HINT:

Before installing the boot, wrap vinyl tape around the spline of the shaft to prevent damaging the boot.



b.

Temporarily install a new boot to the outboard joint shaft.


c.

Position the inside clamp onto the boot.


d.
C115637E01
0.186,0.282 0.509,0.452 0.323,0.170 10 SST 1.77,1.194 0.565,0.471 false

Using SST, pinch the inside clamp.

SST
09521-24010  

NOTICE:

Do not overtighten SST.



e.

Pack the outboard joint and boot with grease in the boot kit.

Standard grease capacity:

292 to 312 g (10.3 to 11.0 oz.)



f.

Position the outside clamp onto the boot.


g.
C115638E01
0.874,0.454 1.238,0.652 0.364,0.198 10 SST 2.155,1.064 1.304,0.617 false

Using SST, pinch the outside clamp.

SST
09521-24010  

NOTICE:

Do not overtighten SST.



h.
C162200E01
0.536,1.52 0.882,1.708 0.346,0.188 10 SST 1.777,1.442 0.923,1.586 false 2.298,1.673 2.792,1.819 0.494,0.147 10 Inside 1.345,0.141 1.923,0.287 0.577,0.147 10 Outside 2.246,0.611 2.155,0.227 2.155,0.227 1.984,0.227 false 2.063,1.463 2.148,1.756 2.148,1.756 2.249,1.756 false

Using SST, adjust the clearance of the clamps.

SST
09240-00020  

Standard clearance:
Clamp Specified Condition
Inside 2.8 to 3.8 mm (0.110 to 0.150 in.)
Outside 3.5 to 4.5 mm (0.138 to 0.177 in.)



Hide 04438A 4.TEMPORARILY INSTALL INBOARD JOINT BOOT

a.

Temporarily install 2 new boot clamps and a boot to the outboard joint shaft.


Hide 5.INSTALL INBOARD JOINT SHAFT

a.
C158357E01
2.661,1.255 3.299,1.595 0.638,0.340 10 Outboard Joint Side

Install the cage to the outboard joint shaft.

NOTICE:

Insert the cage with its smaller inner diameter side facing the outboard joint.



b.
C158394E01
0.876,1.833 2.025,1.766 2.025,1.766 1.353,1.522 false 2.084,1.68 2.858,1.833 0.774,0.152 10 Matchmark

Align the matchmarks placed before removal.


c.

Install the inner race.


d.
C158392

Using a snap ring expander, install a new snap ring.


e.
C158395E01
2.393,1.488 1.449,1.706 1.449,1.706 2.544,1.201 false 1.509,1.693 2.442,1.33 false 0.548,1.621 1.336,1.779 0.788,0.158 10 Matchmark

Align the matchmarks placed before removal, and install the cage to the inner race.


f.
C115633

Install the 6 balls.

HINT:

Apply grease onto the balls to keep them from falling out.



g.

Pack the inboard joint shaft and boot with grease in the boot kit.

Standard grease capacity:

380 to 400 g (13.3 to 14.1 oz.)



h.
C115632E02
0.301,0.199 1.040,0.378 0.739,0.179 10 Matchmark 1.904,0.663 1.195,0.339 false 1.195,0.339 1.519,1.041 false

Align the matchmarks placed before removal, and install the inboard joint shaft to the outboard joint shaft.


i.

Install a new snap ring.


j.

Temporarily install the boot to the inboard joint shaft.

HINT:

Make sure that the boot is on the shaft groove.



k.
C115641E03
1.417,1.458 1.552,1.698 0.135,0.24 12 true A

Check that the 2 boots are not stretched or contracted when the drive shaft is at standard length.

Standard drive shaft length (A):

625.8 mm (2.05 ft.)


If the boots are stretched or contracted, correct them.


l.
C162199E01
0.45,1.521 0.796,1.709 0.346,0.188 10 SST 1.773,1.443 0.836,1.597 false 2.283,1.654 2.777,1.800 0.494,0.147 10 Inside 1.279,0.142 1.857,0.288 0.577,0.147 10 Outside 2.18,0.633 2.089,0.228 2.089,0.228 1.918,0.228 false 2.059,1.464 2.133,1.737 2.133,1.737 2.234,1.737 false

Install the inboard joint boot clamps in the same manner as the outboard side.

HINT:

Adjust the clearance of the inboard joint boot clamps.


Standard clearance:
Clamp Specified Condition
Inside 2.8 to 3.8 mm (0.110 to 0.150 in.)
Outside 3.0 to 4.0 mm (0.118 to 0.158 in.)