Home › Suspension › SUSPENSION › FRONT SHOCK ABSORBER
RM27M0U _53 Suspension _049152 SUSPENSION _0234395 FRONT SHOCK ABSORBER A

SUSPENSION  FRONT SHOCK ABSORBER  REASSEMBLY  


PROCEDURE

Hide 48132 1.INSTALL FRONT COIL SPRING LH

C159782E04
0.469,0.698 0.646,0.813 false 0.167,0.615 0.469,0.823 0.302,0.208 10 false SST

a.

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C263591

Attach the arm of SST to the diameter of the coil spring.

CAUTION:
·

Make sure that the coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




c.

Using SST, compress the coil spring.

CAUTION:
·

If the coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench.




d.
C155966E05
2.698,0.427 2.823,1.094 2.823,1.094 2.823,1.313 false 0.708,1.125 0.479,1.125 false 2.552,1.323 3.24,1.542 0.688,0.219 10 false Lower End 0.188,1.052 0.5,1.208 0.313,0.156 10 false SST

Install the coil spring to the shock absorber.

HINT:

Fit the lower end of the coil spring into the recess of the spring seat of the shock absorber.



Hide 48609 2.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH

a.

Install the 2 cushions, 2 retainers and suspension support to the piston rod.


b.

Temporarily install a new suspension support to front shock absorber nut.


c.

Position the suspension support as shown in the illustration.

C155967E03
1.708,1.5 1.5,1.5 false 2.219,2.063 2.219,2.385 false 2.167,1.74 1.469,2.104 false 1.469,2.104 1.469,2.406 false 2.563,1.896 2.698,2.031 false 2.698,2.031 2.698,2.094 false 2.958,1.521 2.75,1.521 false 2.021,1.146 2.021,0.729 false 2.021,0.729 1.708,0.729 false 2.281,1.135 2.281,0.604 false 2.281,0.604 2.396,0.604 false 4.688,1.708 4.229,2.104 false 4.229,2.104 4.229,2.406 false 4.729,2.021 4.729,2.24 false 4.135,1.375 4.302,1.375 false 5.698,1.365 5.479,1.365 false 4.906,0.896 5.396,0.865 false 5.396,0.865 5.708,0.865 false 4.802,1.115 4.802,0.479 false 4.802,0.479 5.302,0.479 false 5.052,1.625 5.052,2.01 false 5.052,2.01 5.521,2.01 false 1.188,1.427 1.552,1.615 0.365,0.188 10 false 175° 2.604,2.104 2.854,2.25 0.25,0.146 10 false 90° 3,1.448 3.26,1.615 0.26,0.167 10 false 90° 2.042,2.396 3.146,2.583 1.104,0.188 10 false 20 mm (0.787 in.) 0.479,2.417 1.885,2.646 1.406,0.229 10 false Coil Spring Lower End 2,0.083 2.583,0.26 0.583,0.177 10 false LH Side: 4.521,0.083 5.115,0.26 0.594,0.177 10 false RH Side: 2.438,0.521 3.99,0.719 1.552,0.198 10 false Absorber Bush Axis 3.823,2.448 5.271,2.688 1.448,0.24 10 false Coil Spring Lower End 4.438,2.229 5.552,2.406 1.115,0.177 10 false 20 mm (0.787 in.) 5.729,1.292 6.094,1.49 0.365,0.198 10 false 175° 3.917,1.302 4.146,1.479 0.229,0.177 10 false 90° 5.75,0.792 6.031,0.979 0.281,0.188 10 false 90° 5.563,1.917 7.104,2.135 1.542,0.219 10 false Suspension Support Bolt 0.125,0.656 1.708,0.896 1.583,0.24 10 false Suspension Support Bolt 5.354,0.406 6.906,0.604 1.552,0.198 10 false Absorber Bush Axis


d.

Remove SST.

NOTICE:

Do not use an impact wrench. It will damage the shock absorber rod.


HINT:

Release the coil spring while checking the position of the suspension support.



Hide 48680A 3.TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Tighten the nut.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)