Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234411 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) U

AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER


U151881E03
6.24,0.156 6.406,0.333 0.167,0.177 10 false z1 4.115,0.167 4.354,0.344 0.24,0.177 10 false J19

a.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Check from the rear of the connector with it connected to the air conditioning amplifier.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J19-1 (IG+) - J19-14 (GND) P - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch OFF Below 1 V
J19-21 (B) - J19-14 (GND) BR - W-B Battery power source Always 11 to 14 V
J19-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J19-5 (TAM) - J19-14 (GND) V - W-B Ambient temperature sensor signal Ignition switch ON at 25°C (77°F) 1.35 to 1.75 V
Ignition switch ON at 40°C (104°F) 0.9 to 1.2 V
J19-8 (LOCK) - J19-14 (GND) SB - W-B Compressor lock sensor signal Engine is running
Blower switch LO
A/C switch ON
Pulse generation
(see waveform 1)
J19-23 (BLW) - J19-14 (GND) LG - W-B Blower motor control signal Ignition switch ON
Blower switch LO
Pulse generation
(see waveform 2)
J19-20 (MGC) - J19-14 (GND) P - W-B Compressor magnetic clutch operation signal Engine is running
Blower switch LO
A/C switch OFF
11 to 14 V
Engine is running
Blower switch LO
A/C switch ON
Below 1 V
J19-13 (SG-2) - Body ground G - Body ground Ground for ambient temperature sensor Always Below 1 Ω
J19-37 (LIN1) - J19-14 (GND) SB - W-B LIN communication signal Ignition switch ON Pulse generation
J19-11 (CANH) - J19-14 (GND) B - W-B Hi-level CAN bus line Ignition switch ON Pulse generation
(see waveform 3)
J19-12 (CANL) - J19-14 (GND) W - W-B Lo-level CAN bus line Ignition switch ON Pulse generation
(see waveform 4)
z1-2 (BUS G) - Body ground - Ground for BUS IC Always Below 2 V
z1-3 (BUS) - z1-2 (BUS G) - BUS IC control signal Ignition switch OFF → ON Pulse generation
z1-4 (B BUS) - z1-2 (BUS G) - Power supply for BUS IC Always 11 to 14 V
z1-5 (SGA) - Body ground - Ground for No. 1 cooler thermistor Always Below 2 V
z1-6 (TEA) - z1-5 (SGA) - No. 1 cooler thermistor signal Ignition switch ON
No. 1 cooler thermistor at 0°C (32°F)
1.7 to 2.1 V
Ignition switch ON
No. 1 cooler thermistor at 15°C (59°F)
0.7 to 1.3 V


b.
E147483E04
2.906,0.927 3.24,1.073 0.333,0.146 10 false GND 2.396,0.021 3.219,0.229 0.823,0.208 10 false 200 mV/DIV. 1.313,1.875 2.073,2.083 0.76,0.208 10 false 10 ms./DIV.

Using an oscilloscope, check waveform 1.

Compressor lock signal
Terminal No. (Symbols) Tool Setting Condition
J19-8 (LOCK) - J19-14 (GND) 200 mV/DIV., 10 ms./DIV. Engine is running
Blower switch LO
A/C switch ON


c.
E103396E46
2.927,1.646 3.302,1.823 0.375,0.177 10 false GND 2.74,0.26 3.271,0.458 0.531,0.198 10 false 1 V/DIV. 1.063,1.979 2.125,2.156 1.063,0.177 10 false 500 μsec./DIV.

Using an oscilloscope, check waveform 2.

Blower motor control signal
Terminal No. (Symbols) Tool Setting Condition
J19-23 (BLW) - J19-14 (GND) 1 V/DIV., 500 μsec./DIV. Ignition switch ON
Blower switch LO

HINT:

When the blower level is increased, the duty ratio changes accordingly.



d.
E344812E01
2.75,0.292 3.313,0.49 0.563,0.198 10 false 1 V/DIV. 2.99,1.396 3.406,1.594 0.417,0.198 10 false GND 1.594,1.865 2.49,2.094 0.896,0.229 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 3.

CAN communication signal
Terminal No. (Symbols) Tool Setting Condition
J19-11 (CANH) - J19-14 (GND) 1 V/DIV., 10 μsec./DIV. Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



e.
E344813E01
3.031,1.375 3.396,1.583 0.365,0.208 10 false GND 2.76,0.292 3.302,0.5 0.542,0.208 10 false 1 V/DIV. 1.677,1.875 2.583,2.083 0.906,0.208 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 4.

CAN communication signal
Terminal No. (Symbols) Tool Setting Condition
J19-12 (CANL) - J19-14 (GND) 1 V/DIV., 10 μsec./DIV. Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.




CHECK AIR CONDITIONING CONTROL ASSEMBLY


U152847E03
3.438,0.167 3.771,0.354 0.333,0.188 10 false J127

a.

Disconnect the J127 air conditioning control assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J127-4 (IG+) - J127-5 (GND) SB - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch OFF Below 1 V
J127-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J127-7 (STX) - J127-5 (GND) SB - W-B LIN communication signal Ignition switch ON Pulse generation