Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234412 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1421/21  Solar Sensor Circuit (Passenger Side)  


DESCRIPTION

The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output current from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output current increases. As the sunlight decreases, the output current decreases. The air conditioning amplifier detects output current from the solar sensor.

E132508E23
0.417,0.135 2.406,0.385 1.99,0.25 10 false Output Current of Photodiode 0.365,0.813 0.823,1.063 0.458,0.25 10 false High 0.375,2.448 0.833,2.719 0.458,0.271 10 false Low 0.813,2.698 1.333,2.948 0.521,0.25 10 false Weak 2.177,2.677 2.729,2.948 0.552,0.271 10 false Strong 0.802,3.01 2.542,3.25 1.74,0.24 10 false Strength of Solar Radiation

DTC Code DTC Detection Condition Trouble Area
B1421/21 Open or short in passenger side solar sensor circuit
·

Automatic light control sensor (solar sensor)

·

Harness and connector between solar sensor and air conditioning amplifier

·

Harness and connector between solar sensor and main body ECU

·

Main body ECU

·

Air conditioning amplifier



WIRING DIAGRAM

E147579E11
1.26,0.552 1.74,0.813 0.479,0.26 10 false CLTB 1.26,1.073 1.719,1.302 0.458,0.229 10 false CLTE 5.198,0.563 5.635,0.792 0.438,0.229 10 false CLTB 5.198,1.094 5.656,1.281 0.458,0.188 10 false CLTE 1.313,2.438 1.75,2.667 0.438,0.229 10 false TSR 5.198,2.448 5.5,2.677 0.302,0.229 10 false TSP 4.917,0.427 5.146,0.625 0.229,0.198 10 false 20 4.917,0.958 5.146,1.188 0.229,0.229 10 false 18 4.917,2.333 5.135,2.521 0.219,0.188 10 false 32 1.76,0.99 1.948,1.219 0.188,0.229 10 false 3 1.76,0.438 1.927,0.667 0.167,0.229 10 false 6 1.76,2.344 1.938,2.583 0.177,0.24 10 false 2 0.292,2.958 0.635,3.135 0.344,0.177 10 false J128 0.292,3.125 2.219,3.5 1.927,0.375 10 false Automatic Light Control Sensor (Solar Sensor) 5.083,2.979 5.385,3.167 0.302,0.188 10 false J19 5.073,3.135 6.677,3.354 1.604,0.219 10 false Air Conditioning Amplifier 5.344,1.604 5.656,1.833 0.313,0.229 10 false J3 5.344,1.76 6.417,1.979 1.073,0.219 10 false Main Body ECU

CAUTION / NOTICE / HINT

HINT:

If DTC B1244 is output at the same time, troubleshoot DTC B1244 first (see page Vehicle Interior>LIGHTING>LIGHTING SYSTEM>B1244).


PROCEDURE

1.READ VALUE USING TECHSTREAM (SOLAR SENSOR (for Passenger Side))
a.

Use the Data List to check if the passenger side solar sensor is functioning properly.

Air Conditioner
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Solar Sensor (P Side) Passenger side solar sensor /
Min.: 0
Max.: 255
Passenger side solar sensor voltage increases as brightness increases Open in circuit: 0
Short in circuit: 255

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
NG A
OK (Checking from the PROBLEM SYMPTOMS TABLE) B
OK (Checking from the DTC) C



A

2.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR)

B

C

REPLACE AIR CONDITIONING AMPLIFIER

2.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR)
U152687E02
1.865,1.75 2.625,1.75 false 1.51,1.594 0.948,1.896 false 0.094,0.031 2.385,0.375 2.292,0.344 10 false Front view of wire harness connector: (to Solar Sensor) 0.542,1.844 0.958,2.031 0.417,0.188 10 false CLTE 0.677,1.333 1.021,1.51 0.344,0.177 10 false J128 2.667,1.677 3.063,1.854 0.396,0.177 10 false CLTB

a.

Disconnect the J128 solar sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J128-3 (CLTE) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J128-6 (CLTB) - J128-3 (CLTE) Ignition switch ON 11 to 14 V
Ignition switch OFF Below 1 V




OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SOLAR SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SOLAR SENSOR)
E344819E01
0.729,1.656 1.115,1.885 0.385,0.229 0.698,3.896 1.104,4.125 0.406,0.229 1.51,2.156 1.823,1.844 false 1.885,3.854 2.313,4.198 false 0.583,0.031 2.833,0.417 2.25,0.385 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier) 0.698,2.542 2.99,2.927 2.292,0.385 10 false Front view of wire harness connector: (to Solar Sensor) 1.385,2.188 1.729,2.385 0.344,0.198 10 false TSP 0.823,1.688 1.115,1.885 0.292,0.198 10 false J19 0.76,3.927 1.125,4.156 0.365,0.229 10 false J128 2.385,4.156 2.729,4.354 0.344,0.198 10 false TSR

a.

Disconnect the J19 air conditioning amplifier connector.


b.

Disconnect the J128 solar sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J19-32 (TSP) - J128-2 (TSR) Always Below 1 Ω
J19-32 (TSP) or J128-2 (TSR) - Body ground Always 10 kΩ or higher




OK

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR (TSR - CLTE VOLTAGE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR (TSR - CLTE VOLTAGE))
E108193E36
1.5,1.625 0.833,1.719 false 1.917,1.406 2.531,1.646 false 1.49,1.198 0.885,0.875 false 0.427,1.677 0.875,1.896 0.448,0.219 10 false CLTB 0.531,0.729 0.875,0.938 0.344,0.208 10 false TSR 2.583,1.594 3.104,1.823 0.521,0.229 10 false CLTE 0.375,0.104 2.646,0.448 2.271,0.344 10 false Component with harness connected: (Solar Sensor)

a.

Remove the solar sensor with its connector still connected (see page Vehicle Interior>AIR CONDITIONING>SOLAR SENSOR(for Automatic Air Conditioning System)>REMOVAL).


b.

Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
2 (TSR) - 3 (CLTE) Sensor is subjected to electric light 0.8 to 4.3 V
Sensor is covered with a cloth Below 0.8 V


HINT:
·

As the inspection light is moved away from the sensor, the voltage decreases.

·

Use an incandescent light for inspection. Bring it approximately 30 cm (11.8 in.) from the solar sensor.





OK

REPLACE AIR CONDITIONING AMPLIFIER

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR (SOLAR SENSOR)

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR AND BODY GROUND)
U152740E02
2.271,1.594 2.729,1.938 false 2.031,1.604 2.354,2.198 false 1.552,3.917 1.135,4.219 false 1.896,4.125 2.115,4.375 false 0.5,0.219 2.802,0.573 2.302,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 0.49,2.552 2.844,2.906 2.354,0.354 10 false Front view of wire harness connector: (to Solar Sensor) 2.229,2.219 2.604,2.396 0.375,0.177 10 false CLTE 2.635,1.958 3.01,2.135 0.375,0.177 10 false CLTB 0.531,1.458 0.75,1.615 0.219,0.156 10 false J3 0.781,3.75 1.125,3.906 0.344,0.156 10 false J128 1.979,4.385 2.354,4.563 0.375,0.177 10 false CLTB 0.896,4.271 1.271,4.448 0.375,0.177 10 false CLTE

a.

Disconnect the J3 ECU connector.


b.

Disconnect the J128 solar sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J3-18 (CLTE) - J128-3 (CLTE) Always Below 1 Ω
J3-20 (CLTB) - J128-6 (CLTB)
J3-18 (CLTE) or J128-3 (CLTE) - Body ground Always 10 kΩ or higher
J3-20 (CLTB) or J128-6 (CLTB) - Body ground




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR