Home › Vehicle Interior › THEFT DETERRENT › THEFT DETERRENT SYSTEM
RM27M0U _58 Vehicle Interior _049155 THEFT DETERRENT _0234426 THEFT DETERRENT SYSTEM U

THEFT DETERRENT  THEFT DETERRENT SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)


U152761E03
4.75,2.635 5.552,2.635 false 2.333,1.667 2.688,1.667 false 5.5,3.719 5.719,3.896 0.219,0.177 10 false DC 2.573,3.708 2.781,3.885 0.208,0.177 10 false DB 0.635,3.698 0.844,3.875 0.208,0.177 10 false DA 1.99,5.396 2.208,5.573 0.219,0.177 10 false DD 5.479,5.573 5.688,5.75 0.208,0.177 10 false DE 0.635,7.167 0.802,7.344 0.167,0.177 10 false J1 1.865,7.167 2.031,7.344 0.167,0.177 10 false J2 3.521,7.167 3.688,7.344 0.167,0.177 10 false J3 5.427,7.167 5.594,7.344 0.167,0.177 10 false J4 1.875,1.917 2.083,2.094 0.208,0.177 10 false DB 1.875,1.021 2.094,1.198 0.219,0.177 10 false DC 2.229,2.219 2.396,2.396 0.167,0.177 10 false J1 2.219,2.01 2.385,2.188 0.167,0.177 10 false J2 2.74,1.594 2.906,1.771 0.167,0.177 10 false J3 2.198,1.26 2.365,1.438 0.167,0.177 10 false J4 2.135,2.74 2.344,2.917 0.208,0.177 10 false DA 4.625,1.719 4.844,1.896 0.219,0.177 10 false DD 5.604,2.552 5.813,2.729 0.208,0.177 10 false DE

a.

Disconnect the DA, DB, and J4 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
DA-1 (ACC) - Body ground B - Body ground ACC power supply Always 11 to 14 V
DA-1 (IG) - Body ground B - Body ground IG power supply Always 11 to 14 V
DA-1 (ALTB) - Body ground B - Body ground +B power supply Always 11 to 14 V
DB-13 (BECU) - Body ground GR - Body ground BECU power supply Always 11 to 14 V
DB-21 (GND1) - Body ground B - Body ground Body ground Always Below 1 Ω
DB-21 (GND2) - Body ground B - Body ground Body ground Always Below 1 Ω
J4-16 (HCTY) - Body ground V - Body ground Engine hood courtesy switch signal Engine hood closed 10 kΩ or higher
Engine hood open Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the DA, DB and J4 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
J1-4 (IND) - Body ground P - Body ground Security indicator signal Security indicator illuminates
(illuminates only for 60 sec. in alarm sounding state (it is blinking when system is in armed state))
3 to 5 V
J1-6 (SH) - Body ground W - Body ground Security horn signal Armed state Below 1 V
Security horn is sounding
(theft deterrent system is in alarm sounding state)
Pulse generation
J2-4 (HAZ) - Body ground BE - Body ground Hazard warning light signal Armed state Below 1 V
System is in alarm sounding state Pulse generation
J4-17 (GBS)* - Body ground L - Body ground Glass breakage sensor ECU signal Armed state Below 1 V
Glass breakage sensor ECU signal system is in alarm sounding state Pulse generation
DB-1 (HORN) - Body ground V - Body ground Horn signal
(low pitched and high pitched)
Armed state Below 1 V
Horn is sounding 11 to 14 V

HINT:

*: w/ Glass Breakage Sensor


If the result is not as specified, there may be a malfunction on the wire harness side, or the glass breakage sensor ECU may have a malfunction.