RM27M0U
_58
Vehicle Interior
_049157
METER / GAUGE / DISPLAY
_0234436
METER / GAUGE SYSTEM
U
METER / GAUGE / DISPLAY METER / GAUGE SYSTEM FAIL-SAFE CHART
Speedometer:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Vehicle speed pulse is interrupted
|
Controls input signals as 0 km/h (0 mph)
|
Normal data is received
|
| Vehicle speed signal is interrupted
|
Controls input signals as 0 km/h (0 mph)
|
Normal data is received
|
Tachometer:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Engine speed signal is interrupted for 1.2 seconds
|
Controls input signals as 0 rpm
|
Normal data is received
|
Engine coolant temperature gauge:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, engine coolant temperature data is interrupted for 3.1 seconds
|
Gauge needle indicates below "C"
|
Engine coolant temperature data is received
|
Volt gauge (for TFT Display Type):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| EEPROM cannot determine constant value due to EEPROM reading malfunction or other malfunction
|
Default control
|
Normal data is received
|
Fuel signal (Gauge signal):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, sender signal is interrupted for 60 seconds and malfunction signal is received from one of gauges for 10 to 20 seconds
|
Needle indicates "E", and warning light comes on
|
Ignition switch is turned from OFF to ON and normal data is received
|
Odometer:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Vehicle speed pulse signal integration value is interrupted for 0.12 seconds
|
Data received most recently remains displayed
|
Normal data is received
|
A/T shift position indicator:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| "P to D" data is interrupted
|
All data cannot be displayed: Shift position indicator goes off
|
Normal data is received
|
Sequential shift position indicator:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Gear position signal is interrupted
|
Data received most recently remains displayed (when data is interrupted for 3.1 seconds, shift position indicator goes off)
|
Normal data is received
|
| Sequential mode indicator and sequential mode enable signals are interrupted
|
Data received most recently remains displayed (when data is interrupted for 3.1 seconds, shift position indicator goes off)
|
Normal data is received
|
SRS warning light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, SRS warning light on/blink request signal (9.0 V or higher) is interrupted for 10 seconds, or SRS warning light on/blink request signal (below 9 V) is interrupted for 60 seconds
|
SRS warning light remains on until ignition switch off
|
Normal data is received
|
ABS warning light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, ABS warning light signal is interrupted for 1 second
|
ABS warning light remains on until ignition switch off
|
Normal data is received
|
BEAM indicator light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Headlight HI on instruction signal is interrupted for 10 seconds during CAN bus wake-up mode
|
·
Ignition switch is ON: BEAM indicator light condition is maintained
·
Ignition switch is OFF: BEAM indicator light is off
|
Normal data is received
|
Cruise control indicator light (w/ Cruise Control System):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Cruise control indicator light signal is interrupted
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
Front seat belt warning light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Driver side or front passenger side seat belt buckle switch signal is interrupted for 10 seconds during CAN bus wake-up mode
|
·
Ignition switch is ON: Front seat belt warning light condition is maintained
·
Ignition switch is off: Front seat belt warning light is off
|
Normal data is received
|
DOOR indicator light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Driver side courtesy switch, front passenger side courtesy switch, rear door LH courtesy switch, rear door RH courtesy switch and luggage courtesy switch signals are interrupted for 10 seconds during CAN bus wake-up mode
|
·
Ignition switch is ON: DOOR indicator light condition is maintained
·
Ignition switch is OFF: DOOR indicator light is off
|
Normal data is received
|
Brake warning light / Red (Malfunction):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Brake warning light signal is interrupted
|
Brake warning light condition is maintained until ignition switch OFF
|
Normal data is received
|
| While ignition switch is ON position, brake warning light signal is interrupted for 1 second
|
Brake warning light condition is maintained until ignition switch off
|
Normal data is received
|
HEAD indicator light (for U.S.A.):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Headlight LO on request signal is interrupted for 10 seconds during CAN bus wake-up mode
|
·
Ignition switch is ON: HEAD indicator light condition is maintained
·
Ignition switch is OFF: HEAD indicator light is off
|
Normal data is received
|
SLIP indicator light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Frame data (including SLIP indicator on/blink request signal) is interrupted for 0.9 seconds
|
SLIP indicator light condition is maintained until ignition switch OFF
|
Normal data is received
|
TAIL indicator light (except U.S.A.):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| Taillight on request signal is interrupted for 10 seconds during CAN bus wake-up mode
|
·
Ignition switch is ON: TAIL indicator light condition is maintained
·
Ignition switch is off: TAIL indicator light is off
|
Normal data is received
|
Tire pressure warning light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, tire pressure warning signals are interrupted
|
·
Ignition switch is ON: Tire pressure warning light blinks for 60 to 64 seconds
·
Ignition switch is OFF: Tire pressure warning light is off
|
Normal data is received
|
A/T OIL TEMP warning light (for LCD Display Type):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, A/T OIL TEMP warning signals are interrupted
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
CHARGE warning light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, CHARGE warning signals are interrupted
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
Oil pressure warning light (for LCD Display Type):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, OIL PRESSURE warning light request signals are interrupted
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
4LO indicator light (for 4WD):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, frame (including B INDL 4 bit) is interrupted for 3 seconds
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
Washer fluid level warning light (for LCD Display Type):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, washer fluid level low signals are interrupted
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
AUTO LSD indicator light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, frame (including B ALSD bit) is interrupted
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
VSC OFF indicator light:
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, frame (including B TRCW bit) is interrupted for 0.9 seconds
|
Display condition is maintained until ignition switch off
|
Normal data is received
|
TRAC OFF indicator light (for LCD Display Type):
| Condition
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
| While ignition switch is ON, TRAC OFF indicator light signal is interrupted for 1 second
|
Display condition is maintained until ignition switch off
|
Normal data is received
|