Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049158 NAVIGATION / MULTI INFO DISPLAY _0234440 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers the switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E280962E10
2.469,0.438 2.625,0.635 0.156,0.198 10 false 8 2.49,1.229 2.646,1.427 0.156,0.198 10 false 7 5.635,0.406 5.792,0.604 0.156,0.198 10 false 7 5.667,1.188 5.823,1.385 0.156,0.198 10 false 8 2.094,0.552 2.396,0.75 0.302,0.198 10 false TX+ 2.073,1.365 2.375,1.563 0.302,0.198 10 false TX- 5.865,1.385 6.365,1.625 0.5,0.24 10 false TX1- 5.865,0.573 6.49,0.813 0.625,0.24 10 false TX1+ 5.74,1.917 6.24,2.156 0.5,0.24 10 false J135 5.75,2.115 7.042,2.49 1.292,0.375 10 false Navigation Receiver Assembly 1.198,1.896 1.698,2.135 0.5,0.24 10 false J141 1.219,2.063 3.625,2.271 2.406,0.208 10 false Stereo Component Amplifier Assembly 0.875,2.385 3.281,2.594 2.406,0.208 10 false : AVC-LAN communication Line

CAUTION / NOTICE / HINT

HINT:

The navigation receiver assembly is the master unit.


PROCEDURE

1.INSPECT NAVIGATION RECEIVER ASSEMBLY
E280968E02
1.719,0.958 1.219,0.5 false 1.885,0.958 2.448,0.438 false 1.719,0.958 1.219,0.5 false 1.885,0.958 2.448,0.438 false 2.5,0.354 2.927,0.521 0.427,0.167 10 false TX1+ 0.875,0.365 1.573,0.51 0.698,0.146 10 false TX1-

a.

for Column Shift Type:

i.

Remove the navigation receiver assembly with the connector(s) still connected (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER(for Column Shift Type)>REMOVAL).



b.

for Floor Shift Type:

i.

Remove the navigation receiver assembly with the connector(s) still connected (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER(for Floor Shift Type)>REMOVAL).



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

B

C

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the J135 navigation receiver assembly connector.


b.

Disconnect the J141 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J141-8 (TX+) - J135-7 (TX1+) Always Below 1 Ω
J141-7 (TX-) - J135-8 (TX1-) Always Below 1 Ω
J141-8 (TX+) - Body ground Always 10 kΩ or higher
J141-7 (TX-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

REPLACE MALFUNCTIONING PARTS

B

C