Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049158 NAVIGATION / MULTI INFO DISPLAY _0234440 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation receiver assembly via this circuit.

The sound signal that has been sent is amplified by the navigation receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.

WIRING DIAGRAM

E282849E01
0.865,1.073 1.323,1.24 0.458,0.167 10 false AUXO 0.969,1.521 1.427,1.688 0.458,0.167 10 false ARO 0.99,2 1.448,2.167 0.458,0.167 10 false ALO 0.844,2.479 1.302,2.646 0.458,0.167 10 false ASGN 0.854,2.979 1.313,3.146 0.458,0.167 10 false AGND 0.375,3.417 0.833,3.583 0.458,0.167 10 false J100 0.375,3.594 2.052,4 1.677,0.406 10 false No. 1 Stereo Jack Adapter Assembly 2.625,3.156 3.365,3.375 0.74,0.219 10 false Shielded 4.198,3.167 4.844,3.354 0.646,0.188 10 false Shielded 5.99,1.063 6.448,1.229 0.458,0.167 10 false ADPG 5.99,1.542 6.448,1.708 0.458,0.167 10 false VAR+ 5.99,2.021 6.448,2.188 0.458,0.167 10 false VAL+ 5.99,2.51 6.448,2.677 0.458,0.167 10 false VA- 6.01,2.99 6.469,3.156 0.458,0.167 10 false AGND 5.823,3.458 6.281,3.625 0.458,0.167 10 false J135 5.833,3.625 7.094,4 1.26,0.375 10 false Navigation Receiver Assembly 1.375,0.948 1.833,1.115 0.458,0.167 10 false 9 1.385,1.427 1.844,1.594 0.458,0.167 10 false 6 1.365,1.917 1.823,2.083 0.458,0.167 10 false 7 1.365,2.396 1.823,2.563 0.458,0.167 10 false 8 1.354,2.885 1.813,3.052 0.458,0.167 10 false 10 5.708,0.979 5.958,1.156 0.25,0.177 10 false 25 5.708,1.438 5.958,1.615 0.25,0.177 10 false 26 5.698,1.927 5.948,2.104 0.25,0.177 10 false 28 5.708,2.396 5.958,2.573 0.25,0.177 10 false 27 5.698,2.865 5.948,3.042 0.25,0.177 10 false 11

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the J135 navigation receiver assembly connector.


b.

Disconnect the J100 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J135-25 (ADPG) - J100-9 (AUXO) Always Below 1 Ω
J135-26 (VAR+) - J100-6 (ARO) Always Below 1 Ω
J135-28 (VAL+) - J100-7 (ALO) Always Below 1 Ω
J135-27 (VA-) - J100-8 (ASGN) Always Below 1 Ω
J135-11 (AGND) - J100-10 (AGND) Always Below 1 Ω
J135-25 (ADPG) - Body ground Always 10 kΩ or higher
J135-26 (VAR+) - Body ground Always 10 kΩ or higher
J135-28 (VAL+) - Body ground Always 10 kΩ or higher
J135-27 (VA-) - Body ground Always 10 kΩ or higher
J135-11 (AGND) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR