Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049158 NAVIGATION / MULTI INFO DISPLAY _0234440 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E280972E14
0.75,1.813 1.667,2.01 0.917,0.198 10 false J141 1.781,0.74 1.938,0.938 0.156,0.198 10 false 1 5.313,0.76 5.719,0.958 0.406,0.198 10 false 16 5.573,0.885 6.115,1.115 0.542,0.229 10 false MUT1 1.271,0.875 1.75,1.094 0.479,0.219 10 false MUTE 5.49,1.813 5.979,2.031 0.49,0.219 10 false J135 5.49,1.979 6.792,2.615 1.302,0.635 10 false Navigation Receiver Assembly 0.729,1.969 2.469,2.531 1.74,0.563 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U152806E01
0.207,0.166 0.366,0.329 0.159,0.163 10 *a 1.582,0.866 1.916,1.029 0.334,0.163 10 J141 2.699,2.413 3.129,2.576 0.430,0.163 10 MUTE 2.399,1.887 2.861,2.381 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J141-1 (MUTE) - Body ground Ignition switch ACC, audio system playing
→ Changing modes
Above 3.5 V
→ Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the J135 navigation receiver assembly connector.


b.

Disconnect the J141 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J135-16 (MUT1) - J141-1 (MUTE) Always Below 1 Ω
J135-16 (MUT1) - Body ground Always 10 kΩ or higher




OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Disconnect the navigation receiver assembly connector.


b.
U152805E01
1.585,0.69 2.205,0.845 0.620,0.156 10 J135 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 1.054,2.735 1.450,2.890 0.396,0.156 10 MUT1 1.086,2.222 1.371,2.72 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J135-16 (MUT1) - Body ground Ignition switch ACC, audio system is playing Above 3.5 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY