Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234463 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720A 1.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/o Jam Protection Function)

a.
B161799E07
1.469,1.448 1.469,0.104 1.469,0.104 1.083,0.104 false 0.875,0.031 1.083,0.219 0.208,0.188 10 false *1 2.594,1.615 2.813,1.76 0.219,0.146 10 false *c 2.24,2.344 2.438,2.531 0.198,0.188 10 false *b 0.417,2.844 0.615,3.021 0.198,0.177 10 false *a

Apply battery voltage to connector terminals 1 and 2.


b.

Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly LH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise


If the result is not as specified, replace the front power window regulator motor assembly LH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise



Hide 85720A 2.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Jam Protection Function)

E281626E02
1.563,1.635 1.563,0.292 1.563,0.292 1.229,0.292 false 2.677,1.74 2.854,1.906 0.177,0.167 10 false *c 2.313,2.542 2.49,2.708 0.177,0.167 10 false *b 1,0.198 1.198,0.354 0.198,0.156 10 false *1 0.49,3.323 0.708,3.531 0.219,0.208 10 false *a

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals except terminal 2, to avoid damaging the pulse sensor inside the motor.

·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.



a.

Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly LH.

OK:
Measurement Condition Motor Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 10
Auto Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 7
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Manual Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Motor gear rotates counterclockwise


If the result is not as specified, replace the front power window regulator motor assembly LH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise


Hide 85710A 3.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/o Jam Protection Function)

a.
B161800E06
1.844,1.354 1.844,0.188 1.844,0.188 1.583,0.188 false 1.375,0.125 1.563,0.313 0.188,0.188 10 false *1 0.885,2.323 1.104,2.51 0.219,0.188 10 false *c 0.531,1.51 0.75,1.698 0.219,0.188 10 false *b 1.25,2.823 1.469,3.01 0.219,0.188 10 false *a

Apply battery voltage to connector terminals 1 and 2.


b.

Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly RH.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the front power window regulator motor assembly RH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise



Hide 85710A 4.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/ Jam Protection Function)

E281625E02
1.385,1.635 1.385,0.25 1.385,0.25 1.167,0.25 false 0.094,1.719 0.313,1.927 0.219,0.208 10 false *b 0.448,2.552 0.667,2.76 0.219,0.208 10 false *c 0.958,0.156 1.146,0.313 0.188,0.156 10 false *1 0.823,3.323 1.01,3.531 0.188,0.208 10 false *a

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals except terminal 2, to avoid damaging the pulse sensor inside the motor.

·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.



a.

Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly RH.

OK:
Measurement Condition Motor Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 7
Auto Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1, 4 and 10
Motor gear rotates counterclockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 7
Manual Motor gear rotates clockwise
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1 and 10
Motor gear rotates counterclockwise


If the result is not as specified, replace the front power window regulator motor assembly RH.

Text in Illustration
*1 Motor Gear
*a Component without harness connected
(Front Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise