Home › Vehicle Interior › WINDOW / GLASS › BACK POWER WINDOW SWITCH
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234470 BACK POWER WINDOW SWITCH G

WINDOW / GLASS  BACK POWER WINDOW SWITCH  INSPECTION  


PROCEDURE

Hide 84810E 1.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY

B227107E03
2.177,2.844 1.51,2.083 1.51,2.083 1.281,2.083 false 2.375,2.833 1.688,1.698 1.688,1.698 1.448,1.698 false 2.573,2.844 1.865,1.281 1.865,1.281 1.615,1.281 false 2.75,2.833 2.438,1.531 2.438,1.531 2.667,1.531 false 2.854,2.844 2.771,1.969 2.771,1.969 2.906,1.969 false 1.302,3.313 1.583,3.677 1.583,3.677 1.802,3.677 false 0.823,3.917 0.99,4.115 0.167,0.198 10 false *c 1.854,3.594 2.865,3.802 1.01,0.208 10 false *b 0.958,2 1.271,2.208 0.313,0.208 10 false ILL+ 2.958,1.896 3.25,2.073 0.292,0.177 10 false ILL- 2.729,1.448 2.875,1.625 0.146,0.177 10 false E 1.167,1.615 1.406,1.771 0.24,0.156 10 false UP 1.146,1.208 1.625,1.385 0.479,0.177 10 false DOWN 1.604,0.281 1.854,0.448 0.25,0.167 10 false *a

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 2 (E) Pull (Close) Pulled Below 1 Ω
Not pulled 10 kΩ or higher
4 (DOWN) - 2 (E) Push (Open) Pushed Below 1 Ω
Not pushed 10 kΩ or higher


If the result is not as specified, replace the back door power window regulator switch assembly.

Text in Illustration
*a Component without harness connected
(Back Door Power Window Regulator Switch Assembly)
*b Pull (Close)
*c Push (Open)



b.

Check that the LED illuminates.

i.

Apply battery voltage to the back door power window regulator switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 8 (ILL+)
Battery negative (-) → 1 (ILL-)
LED illuminates


If the result is not as specified, replace the back door power window regulator switch assembly.



Hide 84810E 2.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Power Slide Type)

B227028E05
2.177,2.844 1.521,2.083 1.521,2.083 1.281,2.083 false 2.375,2.833 1.688,1.698 1.688,1.698 1.448,1.698 false 2.552,2.833 1.844,1.271 1.844,1.271 1.594,1.271 false 2.74,2.844 2.427,1.542 2.427,1.542 2.656,1.542 false 2.865,2.833 2.792,1.958 2.792,1.958 2.917,1.958 false 1.302,3.313 1.573,3.677 1.573,3.677 1.802,3.677 false 0.833,3.938 1.021,4.156 0.188,0.219 10 false *c 1.844,3.594 2.854,3.802 1.01,0.208 10 false *b 0.958,2 1.26,2.198 0.302,0.198 10 false ILL+ 2.969,1.875 3.26,2.052 0.292,0.177 10 false ILL- 2.729,1.458 2.875,1.635 0.146,0.177 10 false E 1.188,1.604 1.427,1.76 0.24,0.156 10 false UP 1.115,1.198 1.594,1.396 0.479,0.198 10 false DOWN 1.583,0.052 1.802,0.24 0.219,0.188 10 false *a

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 2 (E) Pull (Close) Pulled Below 1 Ω
Not pulled 10 kΩ or higher
4 (DOWN) - 2 (E) Push (Open) Pushed Below 1 Ω
Not pushed 10 kΩ or higher


If the result is not as specified, replace the back door power window regulator switch assembly.



b.

Check that the LED illuminates.

i.

Apply battery voltage to the back door power window regulator switch assembly and check that the LED illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 8 (ILL+)
Battery negative (-) → 1 (ILL-)
LED illuminates


If the result is not as specified, replace the back door power window regulator switch assembly.

Text in Illustration
*a Component without harness connected
(Back Door Power Window Regulator Switch Assembly)
*b Pull (Close)
*c Push (Open)