Home › Vehicle Interior › WINDOW / GLASS › BACK WINDOW GLASS(for CrewMax)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234471 BACK WINDOW GLASS(for CrewMax) G

WINDOW / GLASS  BACK WINDOW GLASS(for CrewMax)  INSPECTION  


PROCEDURE

Hide 85710J 1.INSPECT BACK DOOR POWER WINDOW REGULATOR MOTOR

B171646E01
1.515,2.422 2.192,2.571 0.677,0.149 10 Clockwise 0.633,0.418 1.403,0.567 0.769,0.149 10 Motor Gear 2.018,2.858 3.173,3.006 1.155,0.149 10 Counterclockwise 1.94,1.67 1.723,0.492 1.723,0.492 1.581,0.492 false 2.781,2.105 3,2.105 3,2.105 3,2.831 false

a.

Inspect the operation of the power window regulator motor.

i.

Check that the motor operates smoothly when battery voltage is applied to terminals 1 and 2 as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise


If the result is not as specified, replace the motor.



Hide 85939 2.INSPECT NO. 1 BACK POWER WINDOW RELAY (except 3UR-FBE)

a.

Remove the power window relay from the engine room relay block.


b.
B106753E16
2.49,0.844 2.49,0.615 false 2.854,1.177 3.042,1.177 false 2.49,1.51 2.49,1.708 false 2.073,1.198 2.073,1.729 false 2.479,1.031 1.802,1.031 false 0.813,0.104 0.906,0.302 0.094,0.198 10 false 4 0.302,0.781 0.396,0.979 0.094,0.198 10 false 5 1.281,0.802 1.375,1 0.094,0.198 10 false 3 0.333,1.594 0.427,1.792 0.094,0.198 10 false 1 1.292,1.583 1.385,1.781 0.094,0.198 10 false 2 1.677,0.917 1.771,1.115 0.094,0.198 10 false 4 3.052,1.052 3.146,1.25 0.094,0.198 10 false 5 2.031,1.74 2.125,1.938 0.094,0.198 10 false 3 2.448,0.396 2.542,0.594 0.094,0.198 10 false 1 2.458,1.74 2.552,1.938 0.094,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 4 When battery voltage is not applied between terminals 1 and 2 Below 1 Ω
When battery voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
When battery voltage is applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 85939 3.INSPECT NO. 2 BACK POWER WINDOW RELAY

a.

Remove the power window relay from the engine room relay block.


b.
B106753E16
2.49,0.844 2.49,0.615 false 2.854,1.177 3.042,1.177 false 2.49,1.51 2.49,1.708 false 2.073,1.198 2.073,1.729 false 2.479,1.031 1.802,1.031 false 0.813,0.104 0.906,0.302 0.094,0.198 10 false 4 0.302,0.781 0.396,0.979 0.094,0.198 10 false 5 1.281,0.802 1.375,1 0.094,0.198 10 false 3 0.333,1.594 0.427,1.792 0.094,0.198 10 false 1 1.292,1.583 1.385,1.781 0.094,0.198 10 false 2 1.677,0.917 1.771,1.115 0.094,0.198 10 false 4 3.052,1.052 3.146,1.25 0.094,0.198 10 false 5 2.031,1.74 2.125,1.938 0.094,0.198 10 false 3 2.448,0.396 2.542,0.594 0.094,0.198 10 false 1 2.458,1.74 2.552,1.938 0.094,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 4 When battery voltage is not applied between terminals 1 and 2 Below 1 Ω
When battery voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
When battery voltage is applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 85939 4.INSPECT NO. 3 BACK POWER WINDOW RELAY (for 3UR-FBE)

a.

Remove the power window relay from the engine room relay block.


b.
B106753E16
2.49,0.844 2.49,0.615 false 2.854,1.177 3.042,1.177 false 2.49,1.51 2.49,1.708 false 2.073,1.198 2.073,1.729 false 2.479,1.031 1.802,1.031 false 0.813,0.104 0.906,0.302 0.094,0.198 10 false 4 0.302,0.781 0.396,0.979 0.094,0.198 10 false 5 1.281,0.802 1.375,1 0.094,0.198 10 false 3 0.333,1.594 0.427,1.792 0.094,0.198 10 false 1 1.292,1.583 1.385,1.781 0.094,0.198 10 false 2 1.677,0.917 1.771,1.115 0.094,0.198 10 false 4 3.052,1.052 3.146,1.25 0.094,0.198 10 false 5 2.031,1.74 2.125,1.938 0.094,0.198 10 false 3 2.448,0.396 2.542,0.594 0.094,0.198 10 false 1 2.458,1.74 2.552,1.938 0.094,0.198 10 false 2

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
3 - 4 When battery voltage is not applied between terminals 1 and 2 Below 1 Ω
When battery voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 When battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
When battery voltage is applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.