Home › Vehicle Interior › WINDOW / GLASS › WINDOW DEFOGGER WIRE(for CrewMax)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234472 WINDOW DEFOGGER WIRE(for CrewMax) G

WINDOW / GLASS  WINDOW DEFOGGER WIRE(for CrewMax)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 64811 1.INSPECT BACK WINDOW GLASS (DEFOGGER WIRE)

NOTICE:
·

When cleaning the glass, wipe the glass along the wire using a soft, dry cloth. Take care not to damage the defogger wires.

·

Do not use detergents or glass cleaners that have abrasive ingredients.

·

When measuring voltage, wrap a piece of tin foil around the tip of the negative (-) tester probe and press the foil against the wire with your finger, as shown in the illustration.



B066134E31
1.115,0.458 1.177,0.458 1.177,0.458 1.531,0.948 false 2.406,1.167 2.615,1.167 false 1.406,1.344 1.49,1.479 1.49,1.479 1.583,1.479 false 2.677,1.094 3.26,1.26 0.583,0.167 10 false Tin Foil 1.615,1.396 2.594,1.719 0.979,0.323 10 false Electrical Key Antenna Wire 0.26,0.375 1.094,0.552 0.833,0.177 10 false Tester Probe

a.

Turn the ignition switch ON.


b.

Turn the defogger switch on.


c.
B119840E09
2.333,0.573 1.271,0.979 false 0.781,0.917 1.24,1.104 0.458,0.188 10 false Center

B119841E09
2.24,1.042 1.833,1.885 false 0.885,0.823 1.26,0.823 1.26,0.823 1.719,1.135 false 3.073,0.115 3.125,0.115 3.125,0.115 3.125,0.958 false 2.385,0.708 2.552,0.708 2.552,0.708 2.552,0.958 false 3.24,1.677 2.698,3.104 2.698,3.104 2.417,3.104 false 1.146,0.198 1.281,0.198 1.281,0.198 1.729,0.521 false 0.219,0.75 0.854,0.948 0.635,0.198 10 false Foil Strip 0.365,0.104 1.146,0.302 0.781,0.198 10 false Ground Side 1.354,1.927 2.167,2.115 0.813,0.188 10 false Broken Wire 2.135,0.635 2.375,0.813 0.24,0.177 10 false 0 V 1.844,0.042 3.115,0.24 1.271,0.198 10 false Approximately 10 V 1.604,3.031 2.406,3.219 0.802,0.188 10 false Battery Side

Measure the voltage at the center of each defogger wire as shown in the illustration.

Standard voltage:
Voltage Criteria
Approx. 5 V Wire is not broken
Approx. 10 or 0 V Wire is broken


HINT:

If there is approximately 10 V, the wire may be faulty between the center of the wire and the wire end on the battery side. If there is no voltage, the wire may be faulty between the center of the wire end and the wire end on the ground side.



d.

Place the voltmeter's positive (+) lead against the defogger wire on the battery side.


e.

Place the voltmeter's negative (-) lead with the foil strip against the wire on the ground side.


f.

Slide the positive (+) lead from the battery side to the ground side.


g.

The point where the voltage drops from approximately 10 V to 0 V is where the defogger wire is broken.

HINT:

If the defogger wire is not broken, the voltmeter indicates 0 V at the positive (+) end of the defogger wire and gradually increases to approximately 12 V as the meter probe moves to the other end.