Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234473 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  TERMINALS OF ECU  


CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U151878E02
3.438,0.26 3.698,0.427 0.26,0.167 10 false N12

a.

Disconnect the N12 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N12-2 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V
N12-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the N12 motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N12-10 (UP) - N12-1 (GND) BE - W-B Power window UP operation Ignition switch ON
Master switch
OFF → UP
11 to 14 V → Below 1 V
N12-10 (UP) - N12-1 (GND) BE - W-B Power window UP operation Ignition switch ON
Door glass fully open → power window AUTO UP operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
N12-7 (DOWN) - N12-1 (GND) BR - W-B Power window DOWN operation Ignition switch ON
Master switch
OFF → DOWN
11 to 14 V → Below 1 V
N12-7 (DOWN) - N12-1 (GND) BR - W-B Power window DOWN operation Ignition switch ON
Door glass fully closed → power window AUTO DOWN operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V

If the result is not as specified, the motor may be malfunctioning.



CHECK FRONT POWER WINDOW REGULATOR MOTOR RH


U151877E02
3.427,0.271 3.76,0.448 0.333,0.177 10 false M11

a.

Disconnect the M11 motor connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M11-2 (B) - Body ground V - Body ground Battery power supply Always 11 to 14 V
M11-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the M11 motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M11-10 (UP) - M11-1 (GND) G - W-B Power window UP operation Ignition switch ON
Power window regulator switch assembly
OFF → UP
11 to 14 V → Below 1 V
M11-10 (UP) - M11-1 (GND) G - W-B Power window UP operation Ignition switch ON
Door glass fully open → power window AUTO UP operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
M11-7 (DOWN) - M11-1 (GND) P - W-B Power window DOWN operation Ignition switch ON
Power window regulator switch assembly
OFF → DOWN
11 to 14 V → Below 1 V
M11-7 (DOWN) - M11-1 (GND) P - W-B Power window DOWN operation Ignition switch ON
Door glass fully closed → power window AUTO DOWN operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V
M11-9 (LIN) - M11-1 (GND) L - W-B LIN communication signal Ignition switch ON Pulse generation
M11-4 (AUTO) - M11-1 (GND) B - W-B Power window AUTO UP/DOWN operation Ignition switch ON
Power window regulator switch assembly
OFF → AUTO UP/DOWN operation
11 to 14 V → Below 1 V

If the result is not as specified, the motor may be malfunctioning.



CHECK POWER WINDOW REGULATOR MASTER SWITCH


B442869E01
3.479,0.094 3.688,0.281 0.208,0.188 10 false N2

a.

Disconnect the N2 master switch connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-3 (B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
N2-13 (B) - Body ground P - Body ground Battery power supply Ignition switch ON 11 to 14 V
N2-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the N2 master switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-4 (UP) - N2-1 (E) BE - W-B Driver side door power window UP operation Ignition switch ON, driver side switch of master switch OFF → UP 11 to 14 V → Below 1 V
N2-4 (UP) - N2-1 (E) BE - W-B Driver side door power window AUTO UP operation Ignition switch ON, driver side door glass fully open → power window AUTO UP operation → driver side door glass fully closed 11 to 14 V → Below 1 V → 11 to 14 V
N2-5 (DOWN) - N2-1 (E) BR - W-B Driver side door power window DOWN operation Ignition switch ON, driver side switch of master switch OFF → DOWN 11 to 14 V → Below 1 V
N2-5 (DOWN) - N2-1 (E) BR - W-B Driver side door power window AUTO DOWN operation Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open 11 to 14 V → Below 1 V → 11 to 14 V
N2-12 (U) - N2-1 (E) V - W-B Rear LH side door power window UP operation Ignition switch ON, rear LH switch of master switch OFF → UP Below 1 V → 11 to 14 V
N2-15 (D) - N2-1 (E) B - W-B Rear LH side door power window DOWN operation Ignition switch ON, rear LH switch of master switch OFF → DOWN Below 1 V → 11 to 14 V
N2-10 (U) - N2-1 (E) BE - W-B Rear RH side door power window UP operation Ignition switch ON, rear RH switch of master switch OFF → UP Below 1 V → 11 to 14 V
N2-16 (D) - N2-1 (E) LG - W-B Rear RH side door power window DOWN operation Ignition switch ON, rear RH switch of master switch OFF → DOWN Below 1 V → 11 to 14 V

If the result is not as specified, the master switch may be malfunctioning.



CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)


U152760E02
4.76,2.635 5.563,2.635 false 2.333,1.625 2.688,1.625 false 5.573,3.74 5.792,3.917 0.219,0.177 10 false DC 2.469,3.74 2.677,3.917 0.208,0.177 10 false DB 0.646,3.729 0.854,3.906 0.208,0.177 10 false DA 2.115,5.385 2.333,5.563 0.219,0.177 10 false DD 5.521,5.5 5.729,5.677 0.208,0.177 10 false DE 0.646,7.156 0.813,7.333 0.167,0.177 10 false J1 1.875,7.167 2.042,7.344 0.167,0.177 10 false J2 3.521,7.167 3.688,7.344 0.167,0.177 10 false J3 5.479,7.167 5.646,7.344 0.167,0.177 10 false J4 1.885,1.885 2.094,2.063 0.208,0.177 10 false DB 1.875,1.135 2.094,1.313 0.219,0.177 10 false DC 2.208,2.229 2.375,2.406 0.167,0.177 10 false J1 2.219,1.99 2.385,2.167 0.167,0.177 10 false J2 2.74,1.542 2.906,1.719 0.167,0.177 10 false J3 2.208,1.271 2.375,1.448 0.167,0.177 10 false J4 2.125,2.729 2.333,2.906 0.208,0.177 10 false DA 4.615,1.583 4.833,1.76 0.219,0.177 10 false DD 5.635,2.563 5.844,2.74 0.208,0.177 10 false DE

a.

Disconnect the J3, J4, DA and DD ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
DA-1 (ACC) - Body ground B - Body ground ACC power supply Always 11 to 14 V
DA-1 (IG) - Body ground B - Body ground IG power supply Always 11 to 14 V
DB-21 (GND1) - Body ground B - Body ground Body ground Always Below 1 Ω
DB-21 (GND2) - Body ground B - Body ground Body ground Always Below 1 Ω
J4-24 (DCTY) - Body ground GR - Body ground Front door courtesy light switch LH signal Front door LH open Below 1 Ω
Front door LH closed 10 kΩ or higher
J3-21 (PCTY) - Body ground W - Body ground Front door courtesy light switch RH signal Front door RH open Below 1 Ω
Front door RH closed 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.