Home › Vehicle Interior › MIRROR › OUTER MIRROR SWITCH
RM27M0U _58 Vehicle Interior _049162 MIRROR _0234476 OUTER MIRROR SWITCH G

MIRROR  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

a.
E281074E01
0.206,2.057 0.432,2.282 0.225,0.225 10 *a 2.95,2.519 3.203,2.710 0.253,0.191 10 HR 2.515,2.519 2.768,2.710 0.253,0.191 10 VR 2.056,2.519 2.309,2.710 0.253,0.191 10 VL 1.609,2.519 1.862,2.710 0.253,0.191 10 HL 1.194,2.519 1.447,2.710 0.253,0.191 10 M+ 0.836,2.519 0.975,2.710 0.140,0.191 10 E 0.449,2.519 0.602,2.710 0.154,0.191 10 B 2.184,3.791 3.001,2.734 false 2.029,3.786 2.563,2.734 false 1.889,3.786 2.139,2.734 false 1.739,3.786 1.681,2.734 false 1.586,3.786 1.291,2.734 false 1.435,3.786 0.942,2.734 false 1.29,3.786 0.558,2.734 false

Check the resistance.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Outer Mirror Switch Assembly)

If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror, w/ Memory)

a.
E281073E02
0.503,2.161 0.718,2.353 0.216,0.192 10 *a 2.733,2.547 3.160,2.736 0.426,0.189 10 MSW 2.132,2.547 2.355,2.736 0.223,0.189 10 E1 1.47,2.547 1.752,2.736 0.282,0.189 10 M+ 2.435,3.634 2.806,2.803 false 2.223,3.634 2.222,2.803 false 2.007,3.634 1.612,2.803 false

Inspect the outer mirror switch assembly.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (M+) - 2 (E1) UP Pressed 100 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) DOWN Pressed 470 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) LEFT Pressed 800 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) RIGHT Pressed 250 Ω
Not pressed 10 kΩ or higher
1 (MSW) - 2 (E1) L switch Pressed 100 Ω
Not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Outer Mirror Switch Assembly)

If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (M+) - 2 (E1) UP Pressed 100 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) DOWN Pressed 470 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) LEFT Pressed 800 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) RIGHT Pressed 250 Ω
Not pressed 10 kΩ or higher
1 (MSW) - 2 (E1) R switch Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

a.
E281072E02
0.412,2.102 0.640,2.299 0.228,0.197 10 *a 2.782,2.547 3.177,2.719 0.395,0.172 10 MSW 2.419,2.547 2.619,2.719 0.200,0.172 10 E1 1.969,2.547 2.234,2.719 0.265,0.172 10 M+ 0.697,2.547 0.987,2.719 0.290,0.172 10 MR 1.202,2.547 1.368,2.719 0.166,0.172 10 B 1.551,2.547 1.810,2.719 0.259,0.172 10 E2 0.254,2.547 0.513,2.719 0.259,0.172 10 MF 2.437,3.611 2.904,2.777 false 2.221,3.611 2.49,2.777 false 2.015,3.611 2.061,2.777 false 1.805,3.611 1.693,2.777 false 1.388,3.611 1.286,2.777 false 1.179,3.611 0.911,2.777 false 0.972,3.611 0.458,2.777 false

Inspect the outer mirror switch assembly.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (M+) - 2 (E1) UP Pressed 100 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) DOWN Pressed 470 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) LEFT Pressed 800 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) RIGHT Pressed 250 Ω
Not pressed 10 kΩ or higher
1 (MSW) - 2 (E1) L switch Pressed 100 Ω
Not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Outer Mirror Switch Assembly)

If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (M+) - 2 (E1) UP Pressed 100 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) DOWN Pressed 470 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) LEFT Pressed 800 Ω
Not pressed 10 kΩ or higher
3 (M+) - 2 (E1) RIGHT Pressed 250 Ω
Not pressed 10 kΩ or higher
1 (MSW) - 2 (E1) R switch Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (B) - 7 (MR)
8 (MF) - 4 (E2)
Pressed
(Retracts)
Below 1 Ω
Not pressed 10 kΩ or higher
6 (B) - 8 (MF)
4 (E2) - 7 (MR)
Pressed
(Driving position)
Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.