Home › Vehicle Interior › MIRROR › OUTER REAR VIEW MIRROR
RM27M0U _58 Vehicle Interior _049162 MIRROR _0234478 OUTER REAR VIEW MIRROR G

MIRROR  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (for Standard)

a.
B166373E04
2.073,3.802 1.75,4.177 false 2.458,3.802 2.667,4.01 false 2.281,3.813 2.281,4.135 false 1.167,0.396 1.365,0.573 0.198,0.177 10 true (A) 1.031,1.49 1.229,1.667 0.198,0.177 10 true (B) 0.438,0.927 0.646,1.104 0.208,0.177 10 true (C) 1.604,0.938 1.813,1.115 0.208,0.177 10 true (D) 2.573,4.031 3.021,4.208 0.448,0.177 10 false MV 1.573,4.198 2.021,4.375 0.448,0.177 10 false MH 2.198,4.198 2.646,4.375 0.448,0.177 10 false M+ 0.406,2.594 0.573,2.781 0.167,0.188 10 false *a

Check the outer mirror motor operation.

i.

Apply battery voltage and check operation of the mirror face.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10 (MV)
Battery negative (-) → Terminal 11 (M+)
Turns upward (A)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 10 (MV)
Turns downward (B)
Battery positive (+) → Terminal 12 (MH)
Battery negative (-) → Terminal 11 (M+)
Turns left (C)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 12 (MH)
Turns right (D)


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

w/ Retract Mirror:

Check the retractable mirror's movement.

B443052E01
4.865,1.146 5.021,1.146 5.021,1.146 5.104,1.906 false 5.5,1.188 5.323,1.188 5.323,1.188 5.24,1.917 false 1.521,0.229 1.76,0.427 0.24,0.198 10 false (A) 0.99,1.094 1.198,1.292 0.208,0.198 10 false (B) 0.958,2.302 1.167,2.5 0.208,0.198 10 false (C) 1.938,3.073 2.146,3.271 0.208,0.198 10 false (D) 2.583,3.333 2.792,3.531 0.208,0.198 10 false (E) 4.5,0.542 4.677,0.729 0.177,0.188 10 false *a 4.615,1.083 4.833,1.271 0.219,0.188 10 false MF 5.563,1.094 5.781,1.281 0.219,0.188 10 false MR

i.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.



c.
B166835E04
1.174,4.238 1.493,4.420 0.318,0.181 10 EC+ 2.152,4.238 2.440,4.420 0.288,0.181 10 EC- 1.739,3.771 1.38,4.22 false 0.535,2.52 0.770,2.719 0.235,0.199 10 *c 1.91,3.783 2.25,4.214 false 0.668,0.369 0.911,0.574 0.242,0.205 10 *a 0.668,1.486 0.924,1.691 0.256,0.205 10 *b

w/ EC Mirror:

Check the EC mirror operation.

NOTICE:

Do not apply a voltage of 1.5 V or higher.


i.

Connect a 1.5 V dry-cell battery.


ii.

Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

OK:
Tester Connection Specified Condition
1.5 V dry-cell battery positive (+) → Terminal 14 (EC+)
1.5 V dry-cell battery negative (-) → Terminal 13 (EC-)
Mirror surface becomes dark


Text in Illustration
*a Bright
*b Dark
*c Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.



d.
B166381E03
0.915,2.722 1.238,2.880 0.323,0.159 10 MLP 1.999,2.719 2.383,2.900 0.383,0.181 10 MLP- 0.541,2.35 0.768,2.569 0.228,0.218 10 *a 1.725,3.396 1.725,2.804 1.725,2.804 1.936,2.804 false 1.544,3.396 1.544,2.804 1.544,2.804 1.33,2.804 false

w/ Outer Mirror Light:

Check the door mirror foot light.

i.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 6 (MLP)
Battery negative (-) → Terminal 5 (MLP-)
Door mirror foot light illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer mirror light assembly LH.



e.
B166375E05
2.742,2.922 2.885,3.103 0.143,0.181 10 + 2.593,2.608 2.680,2.790 0.087,0.181 10 - 2.713,3.009 2.639,3.009 2.639,3.009 2.451,3.407 false 2.549,2.714 2.474,2.714 2.474,2.714 2.287,3.403 false 0.545,2.433 0.783,2.657 0.239,0.224 10 *a

w/ Mirror Heater:

Check the mirror heater.

i.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (for Extended Type)

a.
B166365E03
2.083,3.813 1.75,4.188 false 2.469,3.813 2.667,4.021 false 2.271,3.823 2.281,4.146 false 1.219,0.333 1.417,0.51 0.198,0.177 10 true (A) 1.094,1.396 1.292,1.573 0.198,0.177 10 true (B) 0.531,0.771 0.729,1.021 0.198,0.25 10 true (C) 1.646,0.781 1.854,1.031 0.208,0.25 10 true (D) 2.573,4.042 2.906,4.219 0.333,0.177 10 false MV 1.573,4.208 2.021,4.385 0.448,0.177 10 false MH 2.198,4.208 2.646,4.385 0.448,0.177 10 false M+ 0.563,2.479 0.833,2.656 0.271,0.177 10 false *a

Check the outer mirror motor operation.

i.

Apply battery voltage and check operation of the mirror face.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10 (MV)
Battery negative (-) → Terminal 11 (M+)
Turns upward (A)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 10 (MV)
Turns downward (B)
Battery positive (+) → Terminal 12 (MH)
Battery negative (-) → Terminal 11 (M+)
Turns right (D)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 12 (MH)
Turns left (C)


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.



b.
B166831E04
0.954,2.73 1.375,2.911 0.421,0.181 10 TRNL 2.575,2.73 2.943,2.911 0.368,0.181 10 GND 2.509,2.889 2.094,3.395 false 0.635,2.235 0.836,2.426 0.201,0.191 10 *a 1.494,2.876 1.91,3.382 false

Check the door mirror turn indicator.

i.

Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 4 (TRNL)
Battery negative (-) → Terminal 3 (GND)
Door mirror turn indicator illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.



c.
B166833E03
0.365,2.688 0.665,2.869 0.300,0.181 10 RL 2.562,2.715 2.948,2.896 0.386,0.181 10 GND 2.52,2.881 2.104,3.387 false 0.592,2.35 0.847,2.555 0.255,0.204 10 *a 0.583,2.882 0.999,3.389 false

w/ Running Light:

Check the running Light.

i.

Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 9 (RL)
Battery negative (-) → Terminal 3 (GND)
Running light illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.



d.

Check the mirror heater.

i.
B166366E03
2.773,2.918 2.891,3.099 0.118,0.181 10 + 2.59,2.604 2.675,2.786 0.085,0.182 10 - 2.711,3 2.636,3 2.636,3 2.449,3.398 false 2.546,2.705 2.472,2.705 2.472,2.705 2.284,3.394 false 0.63,2.369 0.842,2.561 0.212,0.192 10 *a

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (for Standard)

a.
B166376E05
2.073,3.823 1.719,4.177 false 2.448,3.833 2.656,4.01 false 2.271,3.823 2.271,4.135 false 1.917,0.344 2.115,0.521 0.198,0.177 10 true (A) 2.094,1.458 2.292,1.635 0.198,0.177 10 true (B) 1.427,0.948 1.635,1.125 0.208,0.177 10 true (C) 2.594,0.833 2.802,1.031 0.208,0.198 10 true (D) 2.563,4.031 3.01,4.208 0.448,0.177 10 false MV 1.563,4.198 2.01,4.375 0.448,0.177 10 false MH 2.188,4.198 2.635,4.375 0.448,0.177 10 false M+ 0.542,2.5 0.781,2.698 0.24,0.198 10 false *a

Check the outer mirror motor operation.

i.

Apply battery voltage and check operation of the mirror face.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10 (MV)
Battery negative (-) → Terminal 11 (M+)
Turns upward (A)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 10 (MV)
Turns downward (B)
Battery positive (+) → Terminal 12 (MH)
Battery negative (-) → Terminal 11 (M+)
Turns right (D)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 12 (MH)
Turns left (C)


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

w/ Retract Mirror:

Check the retractable mirror's movement.

B443053E01
5.104,1.969 5.01,1.396 5.01,1.396 4.865,1.396 false 5.271,1.969 5.333,1.406 5.333,1.406 5.49,1.406 false 2.458,0.188 2.698,0.396 0.24,0.208 10 false (A) 2.979,1.115 3.219,1.323 0.24,0.208 10 false (B) 2.99,2.167 3.229,2.375 0.24,0.208 10 false (C) 2.438,2.771 2.677,2.979 0.24,0.208 10 false (D) 1.344,3.188 1.583,3.396 0.24,0.208 10 false (E) 4.313,0.958 4.552,1.167 0.24,0.208 10 false *a 4.625,1.333 4.844,1.51 0.219,0.177 10 false MF 5.521,1.333 5.74,1.51 0.219,0.177 10 false MR

i.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 7 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 7 (MR)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.



c.
B166836E04
1.232,4.242 1.684,4.423 0.453,0.181 10 EC+ 2.188,4.229 2.641,4.410 0.453,0.181 10 EC- 1.74,3.774 1.382,4.223 false 0.618,2.587 0.859,2.791 0.241,0.204 10 *c 1.912,3.786 2.252,4.217 false 2.75,0.295 2.996,0.499 0.246,0.205 10 *a 2.75,1.567 2.961,1.771 0.211,0.205 10 *b

w/ EC Mirror:

Check the EC mirror operation.

NOTICE:

Do not apply a voltage of 1.5 V or higher.


i.

Connect a 1.5 V dry-cell battery.


ii.

Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

OK:
Tester Connection Specified Condition
1.5 V dry-cell battery positive (+) → Terminal 14 (EC+)
1.5 V dry-cell battery negative (-) → Terminal 13 (EC-)
Mirror surface becomes dark


Text in Illustration
*a Bright
*b Dark
*c Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.



d.
B166382E03
0.866,2.732 1.182,2.878 0.316,0.146 10 MLP 2.086,2.729 2.451,2.910 0.365,0.181 10 MLP- 0.701,2.435 0.983,2.656 0.282,0.221 10 *a 1.735,3.393 1.735,2.815 1.735,2.815 2.023,2.815 false 1.552,3.393 1.552,2.815 1.552,2.815 1.279,2.815 false

w/ Outer Mirror Light:

Check the door mirror foot light.

i.

Apply battery voltage to the terminals of the connector, and check the illumination condition.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 6 (MLP)
Battery negative (-) → Terminal 5 (MLP-)
Door mirror foot light illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer mirror light assembly RH.



e.
B166378E07
2.715,2.922 2.831,3.104 0.115,0.181 10 + 2.561,2.613 2.652,2.795 0.092,0.181 10 - 2.696,3.005 2.622,3.005 2.622,3.005 2.434,3.402 false 2.532,2.709 2.457,2.709 2.457,2.709 2.27,3.398 false 0.455,2.274 0.650,2.449 0.195,0.175 10 *a

w/ Mirror Heater:

Check the mirror heater.

i.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (for Extended Type)

a.
B166367E03
2.063,3.802 1.75,4.167 false 2.469,3.813 2.677,4 false 2.271,3.792 2.281,4.125 false 2.146,0.354 2.344,0.531 0.198,0.177 10 true (A) 2.25,1.344 2.448,1.542 0.198,0.198 10 true (B) 1.656,0.906 1.865,1.083 0.208,0.177 10 true (C) 2.781,0.833 2.99,1.01 0.208,0.177 10 true (D) 2.583,4.021 3.031,4.198 0.448,0.177 10 false MV 1.583,4.188 2.031,4.365 0.448,0.177 10 false MH 2.208,4.188 2.656,4.365 0.448,0.177 10 false M+ 0.635,2.427 0.854,2.667 0.219,0.24 10 false *a

Check the outer mirror motor operation.

i.

Apply battery voltage and check operation of the mirror face.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10 (MV)
Battery negative (-) → Terminal 11 (M+)
Turns upward (A)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 10 (MV)
Turns downward (B)
Battery positive (+) → Terminal 12 (MH)
Battery negative (-) → Terminal 11 (M+)
Turns left (C)
Battery positive (+) → Terminal 11 (M+)
Battery negative (-) → Terminal 12 (MH)
Turns right (D)


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.



b.
B166832E03
0.942,2.74 1.385,2.921 0.443,0.181 10 TRNR 2.586,2.74 2.987,2.921 0.401,0.181 10 GND 2.521,2.899 2.105,3.405 false 0.568,2.497 0.794,2.701 0.226,0.204 10 *a 1.505,2.886 1.921,3.392 false

Check the door mirror turn indicator.

i.

Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 4 (TRNR)
Battery negative (-) → Terminal 3 (GND)
Door mirror turn indicator illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.



c.
B166834E03
0.288,2.903 0.560,3.084 0.272,0.181 10 RR 2.761,2.841 3.132,3.022 0.371,0.181 10 GND 2.683,2.928 2.104,3.391 false 0.66,2.435 0.874,2.682 0.215,0.247 10 *a 0.555,3.058 0.981,3.389 false

w/ Running light:

Check the running light.

i.

Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

OK:
Tester Connection Specified Condition
Battery positive (+) → Terminal 9 (RR)
Battery negative (-) → Terminal 3 (GND)
Running light illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.



d.

Check the mirror heater.

i.
B166368E03
2.734,2.912 2.865,3.093 0.131,0.181 10 + 2.59,2.603 2.664,2.785 0.075,0.181 10 - 2.715,2.994 2.64,2.994 2.64,2.994 2.453,3.392 false 2.55,2.699 2.476,2.699 2.476,2.699 2.289,3.388 false 0.589,2.454 0.803,2.642 0.214,0.188 10 *a

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.