Home › Vehicle Interior › EXTERIOR › NAME PLATE
RM27M0U _58 Vehicle Interior _049164 EXTERIOR _0234484 NAME PLATE A

EXTERIOR  NAME PLATE  INSTALLATION  


PROCEDURE

Hide 75444E 1.INSTALL FRONT FENDER PLATE LH

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.

·

When installing the front fender plate LH, heat the vehicle body and front fender plate LH using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Fender Plate LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or front fender plate LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front fender plate LH.

i.

Using a heat light, heat the vehicle body and a new front fender plate LH.


ii.

Remove the peeling paper from the face of the front fender plate LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the front fender plate LH in the position shown in the illustration.

HINT:

Press the front fender plate LH firmly to install it.


B349206E04
3.802,0.885 4.5,1.313 0.698,0.427 10 false 244.9 mm (9.64 in.) 3.792,3.198 4.49,3.625 0.698,0.427 10 false 227.8 mm (8.97 in.) 0.531,3.198 1.229,3.625 0.698,0.427 10 false 234.5 mm (9.23 in.) 0.135,0.094 0.427,0.313 0.292,0.219 10 false *a 5.031,1.646 5.729,2.073 0.698,0.427 10 false 51.6 mm (2.03 in.) 4.969,3.896 5.667,4.323 0.698,0.427 10 false 44.2 mm (1.74 in.) 1.729,3.896 2.427,4.323 0.698,0.427 10 false 43.2 mm (1.70 in.)

Text in Illustration
*a Reference Values - -



Hide 75363C 2.INSTALL DOOR NAME PLATE LH

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.

·

When installing the door name plate LH, heat the vehicle body and door name plate LH using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Door Name Plate LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or door name plate LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new door name plate LH.

i.

Using a heat light, heat the vehicle body and a new door name plate LH.


ii.

Remove the peeling paper from the face of the door name plate LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the door name plate LH in the position shown in the illustration.

HINT:

Press the door name plate LH firmly to install it.


B356296E02
0.083,1.906 0.365,2.146 0.281,0.24 10 false *a 0.073,0.104 0.354,0.344 0.281,0.24 10 false *A 4.156,0.094 4.438,0.333 0.281,0.24 10 false *B 0.521,2.094 1.198,2.438 0.677,0.344 10 false 304 mm (11.97 in.) 5.833,2.104 6.469,2.458 0.635,0.354 10 false 301.5 mm (11.87 in.) 1.49,2.958 2.156,3.344 0.667,0.385 10 false 279 mm (10.98 in.) 5.042,2.958 5.667,3.365 0.625,0.406 10 false 279 mm (10.98 in.)

Text in Illustration
*A for LH Side *B for RH Side
*a Reference Values - -



Hide 75455B 3.INSTALL ROOF SIDE NO. 1 MARK LH

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.

·

When installing the roof side No. 1 mark LH, heat the vehicle body and roof side No. 1 mark LH using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Side No. 1 Mark LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or roof side No. 1 mark LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

for Regular Cab:

i.

Install a new roof side No. 1 mark LH.


ii.

Using a heat light, heat the vehicle body and a new roof side No. 1 mark LH.


iii.

Remove the peeling paper from the face of the roof side No. 1 mark LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iv.

Install the roof side No. 1 mark LH in the position shown in the illustration.

HINT:

press the roof side No. 1 mark LH firmly to install it.


B356297E02
0.083,2 0.646,2.458 0.563,0.458 10 false *a 0.083,0.052 0.646,0.51 0.563,0.458 10 false *A 3.844,0.063 4.406,0.521 0.563,0.458 10 false *B 1,2.51 1.563,2.844 0.563,0.333 10 true 26.8 mm (1.05 in.) 5.563,2.573 6.167,2.896 0.604,0.323 10 true 30.8 mm (1.21 in.) 4.375,3.042 4.969,3.396 0.594,0.354 10 true 60.7 mm (2.39 in.) 2.115,2.99 2.719,3.344 0.604,0.354 10 true 83.7 mm (3.29 in.)

Text in Illustration
*A for LH Side *B for RH Side
*a Reference Values - -



c.

for Double Cab:

i.

Install a new roof side No. 1 mark LH.


ii.

Using a heat light, heat the vehicle body and a new roof side No. 1 mark LH.


iii.

Remove the peeling paper from the face of the roof side No. 1 mark LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iv.

Install the roof side No. 1 mark LH in the position shown in the illustration.

HINT:

press the roof side No. 1 mark LH firmly to install it.


B356298E02
0.021,0 0.271,0.208 0.25,0.208 10 false *a 0.021,0.188 0.271,0.396 0.25,0.208 10 false *A 0.094,3.646 0.344,3.854 0.25,0.208 10 false *B 2.604,2.5 3.229,2.865 0.625,0.365 10 false 220.7 mm (8.69 in.) 1.406,3.615 1.979,3.99 0.573,0.375 10 false 71.9 mm (2.83 in.) 6.094,2.573 6.708,2.927 0.615,0.354 10 false 185.2 mm (7.29 in.) 4.823,3.615 5.375,4 0.552,0.385 10 false 52 mm (2.05 in.) 1.917,7.365 2.469,7.719 0.552,0.354 10 false 68.7 mm (2.7 in.) 5.448,7.365 6.031,7.719 0.583,0.354 10 false 45.2 mm (1.78 in.) 0.625,6.198 1.25,6.625 0.625,0.427 10 true 243.3 mm (9.58 in.) 4.052,6.448 4.688,6.875 0.635,0.427 10 true 214.6 mm (8.45 in.)

Text in Illustration
*A for LH Side *B for RH Side
*a Reference Values - -



d.

for CrewMax:

i.

Install a new roof side No. 1 mark LH.


ii.

Using a heat light, heat the vehicle body and a new roof side No. 1 mark LH.


iii.

Remove the peeling paper from the face of the roof side No. 1 mark LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iv.

Install the roof side No. 1 mark LH in the position shown in the illustration.

HINT:

Press the roof side No. 1 mark LH firmly to install it.


B356299E02
0.021,0 0.271,0.208 0.25,0.208 10 false *a 0.021,0.188 0.271,0.396 0.25,0.208 10 false *A 0.042,3.708 0.292,3.917 0.25,0.208 10 false *B 2.271,2.427 2.938,2.833 0.667,0.406 10 false 273.7 mm (10.78 in.) 1.198,3.656 1.813,3.99 0.615,0.333 10 false 42.2 mm (1.66 in.) 5.667,2.729 6.313,3.083 0.646,0.354 10 false 179.2 mm (7.06 in.) 4.427,3.667 4.99,4.031 0.563,0.365 10 false 29.8 mm (1.17 in.) 2.104,7.385 2.677,7.75 0.573,0.365 10 false 38.5 mm (1.52 in.) 5.563,7.354 6.135,7.719 0.573,0.365 10 false 19.4 mm (0.76 in.) 0.865,6.198 1.51,6.594 0.646,0.396 10 true 296.3 mm (11.67 in.) 4.177,6.479 4.802,6.885 0.625,0.406 10 true 236.8 mm (9.32 in.)

Text in Illustration
*A for LH Side *B for RH Side
*a Reference Values - -



Hide 75473B 4.INSTALL REAR BODY NO. 3 NAME PLATE (for 4WD)

HINT:

When installing the rear body No. 3 name plate, heat the vehicle body and rear body No. 3 name plate using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Body No. 3 Name Plate 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or rear body No. 3 name plate excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear body No. 3 name plate.

i.
B349215E03
1.24,2.74 1.979,3.188 0.74,0.448 10 false 46 mm (1.81 in.) 0.042,0 0.292,0.25 0.25,0.25 10 false *a 0.26,3.625 0.875,4.021 0.615,0.396 10 true 211.3 mm (8.32 in.)

Using a heat light, heat the vehicle body and a new rear body No. 3 name plate.


ii.

Remove the peeling paper from the face of the rear body No. 3 name plate.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Install the rear body No. 3 name plate in the position shown in the illustration.

HINT:

Press the rear body No. 3 name plate firmly to install it.


Text in Illustration
*a Reference Values



Hide 75997C 5.INSTALL REAR BODY STRIPE LH

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedures listed below are for the LH side.

·

When installing the rear body stripe LH, heat the vehicle body and rear body stripe LH using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Body Stripe LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or rear body stripe LH excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame, etc.) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame, etc.) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame, etc.) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in a place with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

B356300E01
0.088,0.081 3.883,1.574 3.796,1.492 0.861,2.351 1.742,2.532 0.882,0.181 10 3 to 7 cm/sec. 3.881,2.227 4.763,2.409 0.882,0.181 10 3 to 7 cm/sec. 2.681,1.758 3.255,1.939 0.575,0.181 10 40 to 50° 6.134,2.886 6.709,3.067 0.575,0.181 10 30 to 45° 2.847,2.564 3.636,2.745 0.789,0.181 10 10 to 20 mm 6.127,2.524 6.916,2.705 0.789,0.181 10 10 to 20 mm 0.687,0.631 0.838,0.48 0.838,0.48 1.002,0.48 false 2.174,0.705 2.296,0.331 2.296,0.331 2.538,0.331 false 2.117,1.242 2.814,1.242 false 2.151,1.959 2.151,1.828 2.151,1.828 2.606,1.828 false 2.097,3.434 2.641,3.434 false 4.596,2.627 4.967,2.627 false 5.726,2.613 5.972,2.956 5.972,2.956 6.088,2.956 false 5.678,3.273 6.074,3.273 false 1.044,2.844 1.801,2.844 1.801,2.844 2.044,2.271 false 0.124,0.116 0.308,0.277 0.184,0.161 10 *a 2.548,0.257 2.736,0.422 0.188,0.165 10 *b 2.833,1.181 3.012,1.323 0.179,0.142 10 *c 1.021,0.401 1.190,0.543 0.170,0.142 10 *1 0.883,2.776 1.053,2.918 0.170,0.142 10 *1 0.082,1.602 0.298,1.767 0.216,0.165 10 *d 1.146,3.405 1.311,3.571 0.165,0.165 10 *2 1.182,2.999 1.372,3.188 0.189,0.189 10 *4 4.492,2.978 4.681,3.167 0.189,0.189 10 *4 4.442,2.575 4.611,2.717 0.170,0.142 10 *1 4.616,3.404 4.781,3.569 0.165,0.165 10 *2 2.669,3.358 2.871,3.527 0.202,0.170 10 *3 3.655,1.616 3.857,1.781 0.202,0.165 10 *e 6.106,3.199 6.285,3.364 0.179,0.165 10 *3 5.157,3.27 4.964,3.463 4.964,3.463 4.767,3.463 false 1.655,3.278 1.466,3.467 1.466,3.467 1.294,3.467 false 1.336,3.077 1.83,3.077 false 4.641,3.05 5.267,3.05 false

NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.



Text in Illustration
*1 Squeegee *2 Rear Body Stripe LH
*3 Release Paper *4 Application Sheet
*a Sectional View *b Non-padded Side
*c Padded Side *d Pressing
*e Pulling - -



f.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners)

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.



g.

Check after installation

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




h.

Install a new rear body stripe LH.

i.

Using a heat light, heat the vehicle body and a new rear body stripe LH.


ii.

Remove the peeling paper from the face of the rear body stripe LH.


iii.

Align the application tape with the rear end character line and using a squeegee, apply the rear body stripe LH.


iv.

Remove the application sheet.

B349216E03
0.99,2.385 0.99,2.521 0.99,2.521 0.771,2.521 false 4.49,2.396 4.49,2.531 4.49,2.531 4.271,2.531 false 3.958,1.771 4.229,2.01 0.271,0.24 10 false *B 0.458,1.781 0.729,2.021 0.271,0.24 10 false *A 0.615,2.406 0.958,2.667 0.344,0.26 10 false *a 4.115,2.417 4.458,2.677 0.344,0.26 10 false *a

Text in Illustration
*A for 2WD *B for 4WD
*a Rear End of Character Line - -