Home › Vehicle Interior › EXTERIOR › ROOF DRIP SIDE FINISH MOULDING
RM27M0U _58 Vehicle Interior _049164 EXTERIOR _0234485 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

When installing a clip, heat the vehicle body and clip using a heat light.

·

When installing the moulding, heat the vehicle body and moulding using a heat light.



Standard heating temperature:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Moulding 20 to 30°C (68 to 86°F)
Clip 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body, moulding and clip excessively.


PROCEDURE

Hide 75561 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

HINT:

Perform this procedure only when installing new clips.


a.

Using a heat light, heat the clip installation areas on the vehicle body.


b.

Remove the double-sided tape from the vehicle body.


c.

Wipe off any tape adhesive residue with cleaner.


d.

Using a heat light, heat the clips.


e.

Remove the peeling paper from the face of the clips.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



f.

Install the clips in the positions shown in the illustration.

HINT:

Press the clips firmly to install them.


B168261E04
0.719,3.438 1.896,3.917 1.177,0.479 12 false for CrewMax: 3.49,4.354 3.896,4.635 0.406,0.281 10 false Front 4.115,4.365 4.813,4.74 0.698,0.375 10 false 5 mm (0.197 in.) 3.646,4.958 4.792,5.26 1.146,0.302 10 false 5 mm (0.197 in.) 5.396,1.656 5.802,1.938 0.406,0.281 10 false Front 1.958,1.635 2.365,1.917 0.406,0.281 10 false Front 6.104,1.677 6.802,2.052 0.698,0.375 10 false 5 mm (0.197 in.) 2.552,1.635 3.25,2.01 0.698,0.375 10 false 5 mm (0.197 in.) 5.646,2.125 6.792,2.427 1.146,0.302 10 false 5 mm (0.197 in.) 2.156,2.115 3.302,2.417 1.146,0.302 10 false 5 mm (0.197 in.) 0.25,0.135 1.625,0.563 1.375,0.427 12 false for Regular Cab: 3.656,0.146 4.927,0.51 1.271,0.365 12 false for Double Cab:


Hide 75552 2.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

a.

Attach the clip to install the moulding.

B168262E04
0.427,3.406 1.635,3.844 1.208,0.438 12 false for CrewMax: 0.344,0.229 1.698,0.646 1.354,0.417 12 false for Regular Cab: 3.729,0.229 5.042,0.583 1.313,0.354 12 false for Double Cab:


Hide 75554A 3.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

If reusing the moulding:

Clean the moulding.

i.

Using a heat light, heat the moulding.


ii.

Remove the double-sided tape from the moulding.


iii.

Wipe off any tape adhesive residue with cleaner.


iv.
B163286E03
1.563,1.896 0.99,1.896 0.99,1.896 0.99,2.208 false 0.563,2.25 1.448,2.844 0.885,0.594 10 false Double-sided Tape

Apply new double-sided tape to the moulding, as shown in the illustration.



c.

Install the moulding.

i.

Using a heat light, heat the vehicle body and moulding.


ii.

Remove the peeling paper from the face of the moulding.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B163282E05
2.25,0.333 2.75,0.333 false 2.74,0.333 2.74,1.979 false 2.74,1.979 2.323,2.302 false 1.094,0.25 2.25,0.438 1.156,0.188 10 true Double-sided Tape

Attach the clip to install the moulding.

HINT:

Press the moulding firmly to install it.