Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › CYLINDER HEAD › from 2016.08
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234038 CYLINDER HEAD A

1UR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A164331E04
1.542,0.677 1.917,0.135 1.917,0.135 1.604,1.167 true 1.948,0.042 2.313,0.208 0.365,0.167 10 false SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A145564

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard Cylinder Head Inside Diameter:
Bush Size Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



e.

Select a new valve guide bush.

New Valve Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore diameter to between 10.335 and 10.356 mm (0.4069 and 0.4077 in.).

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.

HINT:

Standard bush length: 41.3 to 41.7 mm (1.63 to 1.64 in.)



f.
A164332E06
1.521,0.677 1.844,0.135 1.844,0.135 1.583,1.115 true 1.885,0.052 2.24,0.219 0.354,0.167 10 false SST 2.823,0.635 3.313,0.823 0.49,0.188 10 true Height

Using SST and a hammer, tap in a new guide bush to the standard protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

15.8 to 16.2 mm (0.622 to 0.638 in.)



g.
A164333

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A164334E05
2.021,1.063 2.958,1.531 2.958,1.531 1.99,1.281 true 3.01,1.458 3.323,1.635 0.313,0.177 10 false SST

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A145566

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard Cylinder Head Inside Diameter:
Bush Size Specified Condition
STD 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)



e.

Select a new valve guide bush.

New Valve Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore diameter to between 10.335 and 10.356 mm (0.4069 and 0.4077 in.).

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.

HINT:

Standard bush length: 46.8 to 47.2 mm (1.84 to 1.86 in.)



f.
A164335E06
2.031,1.063 2.948,1.521 2.948,1.521 2,1.302 true 3,1.438 3.313,1.594 0.313,0.156 10 false SST 0.094,0.792 0.542,0.979 0.448,0.188 10 true Height

Using SST and a hammer, tap in a new guide bush to the standard protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

15.8 to 16.2 mm (0.622 to 0.638 in.)



g.
A164336

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE SPARK PLUG TUBE

A053854E09
2.573,1.458 2.573,1.354 false 2.573,1.354 1.896,1 false 2.229,1.469 2.948,1.667 0.719,0.198 10 false Adhesive 0.552,1.719 1.042,1.917 0.49,0.198 10 false 15 mm

HINT:

When using a new cylinder head, the spark plug tubes must be replaced.


a.

Remove the spark plug tube.


b.

Apply adhesive to the end of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard seal diameter:

15 mm (0.591 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes after applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing it.




c.
U151528E01
1.968,2.933 3.032,3.108 1.063,0.174 10 75.1 to 76.1 mm 1.216,2.37 2.941,2.554 1.725,0.184 10 Cylinder Head Top Surface 1.159,2.459 0.779,2.459 0.779,2.459 1.139,3.278 false

Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

Standard protrusion height:

75.1 to 76.1 mm (2.96 to 3.00 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 11115A 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins to the cylinder head.

A214829E03
0.281,0.135 0.604,0.344 0.323,0.208 10 false LH: 3.615,0.135 4.01,0.344 0.396,0.208 10 false RH: 3.979,1.063 4.094,1.219 0.115,0.156 10 false A 3.938,1.427 4.083,1.573 0.146,0.146 10 false B 0.833,1.177 0.948,1.333 0.115,0.156 10 false A 0.823,0.625 0.969,0.771 0.146,0.146 10 false B 1.896,3.396 2.01,3.552 0.115,0.156 10 false A 5.167,3.396 5.313,3.542 0.146,0.146 10 false B 3.094,1.177 3.208,1.333 0.115,0.156 10 false A 6.25,1.073 6.365,1.229 0.115,0.156 10 false A 1.26,1.823 1.698,2.01 0.438,0.188 10 false Width 4.51,1.813 4.948,2 0.438,0.188 10 false Width 2.323,2.177 2.844,2.385 0.521,0.208 10 false Height 5.604,2.156 6.125,2.365 0.521,0.208 10 false Height 2.354,2.823 3.521,3.021 1.167,0.198 10 false Protrusion Height 5.635,2.802 6.802,3 1.167,0.198 10 false Protrusion Height

Standard Ring Pin:
Item Height Width Protrusion
Ring pin A 11 mm (0.433 in.) 11 mm (0.433 in.) 5.5 to 6.5 mm (0.217 to 0.256 in.)
Ring pin B 10 mm (0.394 in.) 11 mm (0.433 in.) 3.5 to 6.5 mm (0.138 to 0.256 in.)