Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › CYLINDER HEAD › from 2016.08
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234038 CYLINDER HEAD A

1UR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

a.

Using E7 and E8 "TORX" socket wrenches, install the stud bolts.

Torque:
for stud bolts A, B, C, D : 9.0 N*m (92 kgf*cm, 80 in.*lbf)

U151668E02
0.885,5.438 1.271,5.031 1.271,5.031 1.396,5.031 false 0.885,6.292 1.229,6.469 1.229,6.469 1.229,6.531 false 2.958,5.083 2.802,5.083 2.802,5.083 2.469,5.646 false 2.479,6.24 2.76,6.385 2.76,6.385 2.76,6.469 false 5.615,5.927 5.938,5.177 5.938,5.177 6.063,5.177 false 4.5,5.125 4.365,5.125 4.365,5.125 4.125,5.875 false 0.802,0.917 0.802,1.354 true 6.604,0.99 6.604,1.417 true 1.104,2.75 1.104,3.021 false 1.365,2.771 1.365,3.021 false 1.802,3.031 1.802,3.104 false 1.688,2.458 1.688,3.021 false 2.229,2.771 2.229,3.021 false 2.49,2.458 2.49,3.021 false 4.75,2.729 4.75,3.01 true 5.021,2.448 5.021,3 true 5.583,2.448 5.583,3 false 5.875,2.76 5.875,3.01 false 6.135,2.771 6.135,3.01 false 5.542,3.031 5.542,3.104 false 2.667,4.01 3.063,4.01 false 2.573,4.292 2.813,4.292 2.813,4.292 2.813,4.01 false 4.917,4.281 4.552,4.281 false 4.813,4.01 4.677,4.01 4.677,4.01 4.677,4.281 false 4.896,3.917 4.531,3.917 false 4.135,6.229 4.406,6.375 4.406,6.375 4.406,6.458 false 5.615,6.271 5.885,6.417 5.885,6.417 5.885,6.5 false 0.469,0.083 1.917,0.292 1.448,0.208 10 false Intake Side of RH: 4.177,0.073 5.625,0.281 1.448,0.208 10 false Intake Side of LH: 4.177,1.708 5.75,1.917 1.573,0.208 10 false Exhaust Side of LH: 0.469,1.708 2.073,1.917 1.604,0.208 10 false Exhaust Side of RH: 0.469,3.406 1.865,3.615 1.396,0.208 10 false Front Side of RH: 4.177,3.396 5.51,3.604 1.333,0.208 10 false Front Side of LH: 1.458,4.938 2.146,5.302 0.688,0.365 10 false 12 mm (0.472 in.) 1.396,5.688 2.073,6.052 0.677,0.365 10 false 52 mm (2.05 in.) 2.479,6.49 3.635,6.698 1.156,0.208 10 false 13 mm (0.512 in.) 3.01,5.01 3.729,5.427 0.719,0.417 10 false 24 mm (0.945 in.) 2.938,5.76 3.594,6.125 0.656,0.365 10 false 45 mm (1.77 in.) 4.552,5.042 5.271,5.469 0.719,0.427 10 false 20 mm (0.787 in.) 6.104,5.073 6.792,5.479 0.688,0.406 10 false 14 mm (0.551 in.) 4.594,5.865 5.26,6.24 0.667,0.375 10 false 35 mm (1.38 in.) 6.104,5.875 6.792,6.24 0.688,0.365 10 false 29 mm (1.14 in.) 0.563,6.417 0.719,6.583 0.156,0.167 10 false A 4.406,3.844 4.552,4.021 0.146,0.177 10 false A 2.177,6.406 2.313,6.583 0.135,0.177 10 false B 1.76,3.115 1.896,3.292 0.135,0.177 10 false C 5.49,3.125 5.625,3.302 0.135,0.177 10 false C 3.802,6.406 3.948,6.604 0.146,0.198 10 false C 0.76,1.365 0.906,1.531 0.146,0.167 10 false B 6.552,1.458 6.698,1.656 0.146,0.198 10 false B 5.302,6.406 5.438,6.552 0.135,0.146 10 false D 4.406,4.188 4.552,4.344 0.146,0.156 10 false D 3.094,3.958 3.25,4.115 0.156,0.156 10 false D 0.906,6.49 2.042,6.677 1.135,0.188 10 false 12 mm (0.472 in.) 4.125,6.479 5.281,6.688 1.156,0.208 10 false 13 mm (0.512 in.) 5.625,6.5 6.781,6.708 1.156,0.208 10 false 13 mm (0.512 in.)


Hide 11117F 2.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A164330E04
0.208,0.083 1.531,0.417 1.323,0.333 10 true Front Side of RH: 0.219,2.417 1.323,2.583 1.104,0.167 10 false Front Side of LH:

Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A145550E03
0.077,2.27 0.342,2.452 0.265,0.181 10 LH: 0.077,0 0.388,0.174 0.311,0.174 10 RH:

Using a 10 mm hexagon wrench, install 6 new gaskets and the 6 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 13734 4.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 13711A 5.INSTALL VALVE STEM OIL SEAL

a.

Apply a light coat of engine oil to new oil seals.

A321194E02
1.94,1.178 2.791,1.422 0.850,0.244 10 Black 5.17,1.165 6.020,1.409 0.850,0.244 10 Gray 1.328,0.656 1.468,0.516 false 2.432,0.786 2.189,1.166 false 4.974,0.478 4.706,0.591 false 5.756,1.067 5.518,1.214 false 0.322,0.179 3.442,1.524 3.12,1.345 3.765,0.179 6.885,1.524 3.12,1.345 0.42,0.24 1.271,0.484 0.850,0.244 10 Intake Side 3.862,0.24 4.810,0.484 0.948,0.244 10 Exhaust Side 1.522,0.429 2.373,0.673 0.850,0.244 10 Gray 5.032,0.394 5.882,0.638 0.850,0.244 10 Black

NOTICE:

Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal into the intake side can cause installation problems later.


HINT:
·

for Intake Side

The intake side valve stem oil seals is gray or black.

·

for Exhaust Side

The exhaust side valve stem oil seals is black or gray.




b.
A165065E01
0.154,1.522 0.537,1.724 0.383,0.202 10 SST 0.57,1.601 1.571,1.128 false 0.588,2.223 1.334,2.386 0.746,0.163 10 CORRECT 1.993,2.213 2.848,2.401 0.855,0.188 10 INCORRECT

Using SST, push in the oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 6.INSTALL INTAKE VALVE

a.
A380012E01
1.708,1.698 3.271,1.896 1.563,0.198 10 false 40 mm (1.57 in.) or more

Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.


b.
A366793E01
0.604,1.635 0.604,1.458 false 0.615,0.625 0.49,0.292 0.49,0.292 0.615,0.292 false 0.667,0.208 1.177,0.396 0.51,0.188 10 false Narrow 0.448,1.656 0.844,1.865 0.396,0.208 10 false Wide

Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A366791E01
2.917,0.323 3.01,0.323 false 0.438,0.656 0.563,0.656 0.563,0.656 0.667,0.844 true 0.094,0.573 0.448,0.771 0.354,0.198 10 false SST 3.063,0.229 3.417,0.427 0.354,0.198 10 true SST

Using SST and wooden blocks, compress the spring and install the valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


d.
A366795

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.




Hide 13715 7.INSTALL EXHAUST VALVE

a.
A380012E01
1.708,1.698 3.271,1.896 1.563,0.198 10 false 40 mm (1.57 in.) or more

Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.


b.
A366794E01
0.781,1.625 0.781,1.417 false 0.781,0.594 0.698,0.281 0.698,0.281 0.844,0.281 false 0.896,0.188 1.406,0.406 0.51,0.219 10 false Narrow 0.635,1.646 1.031,1.854 0.396,0.208 10 false Wide

Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A366792E01
0.417,0.271 0.542,0.271 false 2.99,1.698 2.885,1.698 2.885,1.698 2.792,1.594 true 0.104,0.188 0.438,0.396 0.333,0.208 10 false SST 3.031,1.615 3.365,1.823 0.333,0.208 10 false SST

Using SST and wooden blocks, compress the spring and install the valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


d.
A366796

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.