Refer to DTC P0712 (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>P0712).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0711 | Either condition is met (2-trip detection logic):
(a) Certain monitor enabling conditions are met and the ATF temperature is below 20°C (68°F). (b) Certain monitor enabling conditions are met and the ATF temperature is 105°C (221°F) or higher. |
No. 1 transmission wire (No. 1 ATF temperature sensor) |
This DTC indicates that there is a problem with output from the Automatic Transmission Fluid (ATF) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, turns on the MIL and stores the DTC.
When the ATF temperature is 105°C (221°F) or more and engine coolant temperature reaches 60°C (140°F) after cold start, the ECM also determines this as a fault, turns on the MIL and stores the DTC.
| Related DTCs | P0711: ATF temperature sensor/Rationality fault diagnostics |
| Required sensors/Components | ATF temperature sensor |
| Frequency of operation | Continuous |
| Duration | Condition (A), (B), (C) and (D): 3 seconds
Condition (E): Continuous |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor "A" circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine Coolant Temperature) sensor circuit) P0110, P0111, P0112, P0113 (IAT (Intake air temperature) sensor circuit) P2610 (Soak timer circuit) |
| Duration time from engine start | 12 seconds or more |
| ECT | -15°C (5°F) or higher |
| Permission flag for ATF temperature rationality check | ON |
| Time after engine start except for continuing shift position "N" or "P"*2 | 10 minutes or more |
| Accumulated driving time*1 | 90 seconds or more |
| Driving distance after engine start*3 | 4.9 km (3.0 miles) or more |
| ECT (12 seconds after engine start) | 15°C (59°F) or higher |
| IAT*4 | 15°C (59°F) or higher |
| Soak time | 5 hours or more |
| Duration time from engine start | 12 seconds or more |
| ECT | -15°C (5°F) or higher |
| Permission flag for ATF temperature rationality check | ON |
| Time after engine start except for continuing shift position "N" or "P"*2 | 21 minutes and 40 seconds or more |
| Accumulated driving time*1 | 250 seconds or more |
| Driving distance after engine start*3 | 9.0 km (5.6 miles) or more |
| ECT (12 seconds after engine start) | -10°C (14°F) or higher |
| IAT*4 | -10°C (14°F) or higher |
| Duration time from engine start | 12 seconds or more |
| ECT | -15°C (5°F) or higher |
| Permission flag for ATF temperature rationality check | ON |
| Time after engine start except for continuing shift position "N" or "P"*2 | 30 minutes or more |
| Accumulated driving time*1 | 400 seconds or more |
| Driving distance after engine start*3 | 16.0 km (9.9 miles) or more |
| ECT (12 seconds after engine start) | -15°C (5°F) or higher |
| IAT*4 | -15°C (5°F) or higher |
| Duration time from engine start | 12 seconds or more |
| ECT | -15°C (5°F) or higher |
| Permission flag for ATF temperature rationality check | ON |
| Time after engine start except for continuing shift position "N" or "P"*2 | 55 minutes or more |
| Accumulated driving time*1 | 750 seconds or more |
| Driving distance after engine start*3 | 27.0 km (16.8 miles) or more |
| Duration time for ECT to reach 60°C (140°F) | 10 seconds or more |
| ATF temperature (12 seconds after engine start) | 105°C (221°F) or higher |
| ECT (12 seconds after engine start) | Below 35°C (95°F) |
| Engine speed - Turbine speed | 50 rpm or more |
| Output speed | 400 rpm or more |
| Throttle valve opening angle | 5.5% or more |
| Shift position | Not "N" or "P" |
| Engine | Starting |
| However, accumulated driving time is cleared | - |
| When following condition met | - |
| Duration time from shift position "N" or "P" | 300 seconds or more |
| Duration time from shift position "N" or "P" | 300 seconds or more |
| Duration time from shift position "N" or "P" | 300 seconds or more |
| 12 sec. after engine start | - |
| Duration time from shift position "N" or "P" | 300 seconds or more |
When either condition below is met: Condition (A)*, (B), (C), (D) or (E)
| ATF temperature | Below 20°C (68°F) |
*: Except Mexico models
| ATF temperature | 105°C (221°F) or higher |
| ATF temperature | 20°C (68°F) or higher, and below 105°C (221°F) |
*: Except Mexico models
Refer to DTC P0712 (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>P0712).
Perform the universal trip to clear permanent DTCs (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
If DTCs P0711 and P2610 are output simultaneously, confirm that the ATF temperature is as specified in "Normal Condition" using the Techstream first. When the ATF temperature is as specified in "Normal Condition", perform troubleshooting for DTC P2610 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P2610 for 3UR-FE, See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P2610 for 3UR-FBE).
DATA LIST
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F) Max.: 150°C (302°F) |
·
After stall test: Approximately 80°C (176°F) ·
With engine cold: Equal to ambient temperature |
If value is -40°C (-40°F) or 150°C (302°F), No. 1 ATF temperature sensor circuit is open or shorted |
When DTC P0712 is output and the Techstream output is 150°C (302°F) or more, there is a short circuit.
When DTC P0713 is output and the Techstream output is -40°C (-40°F), there is an open circuit.
Check the temperature displayed on the Techstream in order to check if a malfunction exists.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 150°C (302°F) or more | Short circuit |
If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected. It is not necessary to inspect the circuit when P0711 is set.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
|---|---|
| Only P0711 is output | A |
| P0711 and other DTCs are output | B |
If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.
A
B
Check the transmission fluid level (See page Drivetrain>AB60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION FLUID>ADJUSTMENT).
Automatic transmission fluid level is correct.
OK
NG