| *1 | WASHER | *2 | TRANSMISSION CONTROL SHAFT LEVER |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 6 | TRANSMISSION REVOLUTION SENSOR (NT) | 89413N | - | - | - |
| 7 | TRANSMISSION REVOLUTION SENSOR (NSS) | 89413T | - | - | - |
| 8 | OIL PRESSURE SENSOR | 89637K | - | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
| *1 | TEMPERATURE SENSOR CLAMP | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 18 | TRANSAXLE HOUSING | 35111C | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| *1 | SNAP RING | - | - |
| ● | Non-reusable part | - | - |
| *1 | TORSION SPRING | *2 | SHIM |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 30 | FRONT DRIVE SHAFT OIL SEAL RH | 43410M | ( )
|
- | - |
| 31 | CVT TYPE T OIL SEAL | - | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| *1 | THRUST NEEDLE ROLLER BEARING | *2 | TRANSMISSION DRIVE CHAIN |
| *3 | SNAP RING | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 38 | FRONT OIL PUMP ASSEMBLY | 35310A | ( )
|
- | - |
| 39 | OIL STRAINER ASSEMBLY | 35330J | - | - | - |
| 40 | NO. 1 TRANSMISSION CASE PLATE | 35165B | - | - | - |
| 41 | STATOR (CVT) SHAFT ASSEMBLY | 35370E | - | - | - |
| *1 | FRONT OIL PUMP ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 42 | 1ST GEAR SUB-ASSEMBLY | 33032 | ( )
|
- | - |
| 43 | NO. 1 GEAR SHIFT FORK ASSEMBLY | 33210A | ( )
|
- | - |
| 44 | STAY | - | - | - | - |
| 45 | FORWARD MULTIPLE DISC CLUTCH ASSEMBLY | 35610A | ( )
|
- | - |
| *1 | THRUST BEARING RACE | - | - |
| *1 | SNAP RING | *2 | FORWARD CLUTCH FLANGE |
| *3 | FORWARD MULTIPLE DISC CLUTCH CLUTCH PLATE | *4 | FORWARD CLUTCH DRUM SUB-ASSEMBLY |
| ● | Non-reusable part | - | - |
| *1 | STATOR (CVT) SHAFT ASSEMBLY | *2 | THRUST NEEDLE ROLLER BEARING |
| *3 | SNAP RING | *4 | BRAKE FLANGE |
| *5 | NO. 1 BRAKE PLATE | *6 | BRAKE CUSHION PLATE |
| ● | Non-reusable part | - | - |
| *1 | SNAP RING | - | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
Clean the work area, tools to be used, other equipment, etc., thoroughly before performing this procedure, as there is a possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.
Do not use cotton work gloves, cloths, paper towels, etc., that may produce lint, dust or foreign matter.
When cleaning parts, make sure that dust or foreign matter does not enter the CVT.
When replacing any tapered roller bearing (inner race) or tapered roller bearing (outer race), replace both the tapered roller bearing (inner race) and tapered roller bearing (outer race) with new ones.
When the tapered roller bearing (inner race) is removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) need to be replaced.
When the tapered roller bearing (inner race) is not removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) can be reused.
Shift shock may increase after replacing the transmission valve body assembly or forward multiple disc clutch assembly. In this case, shift shock will reduce as the vehicle is driven.
33493C
1.REMOVE TRANSMISSION OIL COOLER ASSEMBLY
84540
2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
| *a | Piece of Wood or Equivalent | - | - |
Using a piece of wood or equivalent to secure the transmission control shaft lever to prevent it from rotating, remove the nut, washer and transmission control shaft lever from the manual valve lever shaft.
| *1 | Transmission Control Shaft Lever |
| *2 | Manual Valve Link Lever Sub-assembly |
| *3 | Manual Valve |
If the transmission control shaft lever is not secured when loosening the nut, the manual valve link lever sub-assembly may separate from the manual valve.
Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.
89419B
3.REMOVE SHIFT STROKE SENSOR
89413M
4.REMOVE TRANSMISSION REVOLUTION SENSOR (NOUT)
35151K
5.REMOVE AUTOMATIC TRANSMISSION CASE COVER
89413N
6.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)
89413T
7.REMOVE TRANSMISSION REVOLUTION SENSOR (NSS)
89637K
8.REMOVE OIL PRESSURE SENSOR
9.REMOVE REFILL PLUG
30400
10.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
| *a | Wooden Block | - | - |
Place the continuously variable transaxle assembly on wooden blocks.
35125F
11.REMOVE OVERFLOW PLUG
Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle case sub-assembly.
35125E
12.REMOVE OVERFLOW(CVT) TUBE
Using a 6 mm hexagon socket wrench, remove the overflow (CVT) tube from the transaxle case sub-assembly.
35015Y
13.REMOVE TRANSAXLE SIDE COVER SUB-ASSEMBLY
Remove the 11 bolts and transaxle side cover sub-assembly from the transaxle case sub-assembly.
Remove the O-ring from the transaxle side cover sub-assembly.
82125M
14.SEPARATE TRANSMISSION WIRE
Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.
Disconnect the 6 solenoid valve connectors.
Remove the bolt and temperature sensor clamp from the transmission valve body assembly.
Disconnect the temperature sensor from the transmission valve body assembly.
35410J
15.REMOVE TRANSMISSION VALVE BODY ASSEMBLY
Temporarily install the transmission control shaft lever to the manual valve lever shaft.
Turn the transmission control shaft lever clockwise until it stops.
Remove the transmission control shaft lever from the manual valve lever shaft.
Remove the 11 bolts and valve body assembly from the transaxle case sub-assembly.
Make sure the manual valve does not fall out when removing the transmission valve body assembly, as the manual valve is not secured to the transmission valve body assembly.
Remove the front oil pump cover gasket from the transaxle case sub-assembly.
Remove the 3 transaxle case gaskets from the transaxle case sub-assembly.
82125M
16.REMOVE TRANSMISSION WIRE
Disconnect the transmission revolution sensor (NC1) connector.
Remove the bolt and transmission wire from the transaxle case sub-assembly.
Remove the O-ring from the temperature sensor.
89413S
17.REMOVE TRANSMISSION REVOLUTION SENSOR (NC1)
35111C
18.REMOVE TRANSAXLE HOUSING
Remove the 20 bolts.
Using a plastic hammer, tap on the circumference of the transaxle housing to remove it from the transaxle case sub-assembly.
Remove the 5 O-rings from the transaxle case sub-assembly.
35174B
19.REMOVE OIL RESERVOIR LOCK PLATE
35394D
20.REMOVE OIL CLEANER(CVT) MAGNET
35882E
21.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE
35896A
22.REMOVE SECONDARY SHAFT LUBE APPLY TUBE
Using a snap ring plier, remove the snap ring from the transaxle housing.
Remove the secondary shaft lube apply tube from the transaxle housing.
Remove the O-ring from the secondary shaft lube apply tube.
35809
23.REMOVE C-2 CLUTCH PRESSURE APPLY TUBE SUB-ASSEMBLY
Remove the C-2 clutch pressure apply tube sub-assembly from the transaxle housing.
Remove the O-ring from the C-2 clutch pressure apply tube sub-assembly.
35593A
24.REMOVE CAM GUIDE SLEEVE
35556N
25.REMOVE PARKING LOCK PAWL SHAFT
| *1 | Parking Lock Pawl Shaft | *2 | Torsion Spring |
Remove the parking lock pawl shaft and torsion spring from the transaxle housing.
35557C
26.REMOVE PARKING LOCK PAWL
35598B
27.REMOVE PARKING LOCK SLEEVE
28.REMOVE REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the reduction driven gear front tapered roller bearing (outer race) and shim from the transaxle housing.
Be careful not to damage the transaxle housing.
Align the claw of SST with the indentation of the transaxle housing when removing the parts.
29.REMOVE DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the differential case front tapered roller bearing (outer race) and shim from the transaxle housing.
Be careful not to damage the transaxle housing.
Align the claw of SST with the indentation of the transaxle housing when removing the parts.
43410M
30.REMOVE FRONT DRIVE SHAFT OIL SEAL RH
Using SST and a hammer, remove the front drive shaft oil seal RH from the transaxle housing.
31.REMOVE CVT TYPE T OIL SEAL
Using SST and a hammer, remove the transaxle housing type T oil seal from the transaxle housing.
35759A
32.REMOVE REDUCTION DRIVEN GEAR
33.REMOVE DIFFERENTIAL CASE SUB-ASSEMBLY
35317A
34.REMOVE NO. 2 TRANSMISSION OIL PUMP SEPARATE PLATE
35782P
35.REMOVE DRIVE SPROCKET
| *1 | Drive Sprocket | *2 | Transmission Drive Chain |
Remove the thrust needle roller bearing from the drive sprocket.
Remove the drive sprocket and transmission drive chain.
35783N
36.REMOVE DRIVEN SPROCKET
Using a snap ring expander, remove the driven sprocket from the front oil pump assembly.
Remove the snap ring from the front oil pump assembly.
35316A
37.REMOVE NO. 1 TRANSMISSION OIL PUMP SEPARATE PLATE
35310A
38.REMOVE FRONT OIL PUMP ASSEMBLY
Remove the 4 bolts and front oil pump assembly from the transaxle case sub-assembly.
Remove the front oil pump cover gasket from the transaxle case sub-assembly.
35330J
39.REMOVE OIL STRAINER ASSEMBLY
35165B
40.REMOVE NO. 1 TRANSMISSION CASE PLATE
35370E
41.REMOVE STATOR (CVT) SHAFT ASSEMBLY
33032
42.REMOVE 1ST GEAR SUB-ASSEMBLY
33210A
43.REMOVE NO. 1 GEAR SHIFT FORK ASSEMBLY
Move the No. 1 gear shift fork assembly as shown in the illustration.
Remove the No. 1 gear shift fork assembly from the 1st gear sub-assembly.
44.REMOVE STAY
35610A
45.REMOVE FORWARD MULTIPLE DISC CLUTCH ASSEMBLY
Remove the forward multiple disc clutch assembly from the planetary gear assembly.
Remove the thrust bearing race from the forward multiple disc clutch assembly.
35633H
46.REMOVE FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC
| *1 | Forward Clutch Flange | *2 | Forward Multiple Disc Clutch Clutch Disc |
| *3 | Forward Multiple Disc Clutch Clutch Plate | - | - |
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the forward clutch drum sub-assembly.
Be careful not to damage the forward clutch drum sub-assembly.
Remove the forward clutch flange, 3 forward multiple disc clutch clutch discs and 3 forward multiple disc clutch clutch plates from the forward clutch drum sub-assembly.
47.REMOVE NO. 1 CLUTCH BALANCER
Place SST on the No. 1 clutch balancer and compress the forward clutch return spring sub-assembly with a press.
Do not compress the forward clutch return spring sub-assembly excessively.
Using a snap ring expander, remove the snap ring from the forward clutch drum sub-assembly.
Remove the No. 1 clutch balancer from the forward clutch drum sub-assembly.
Remove the D-ring from the No. 1 clutch balancer.
35603E
48.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY
35612D
49.REMOVE FORWARD CLUTCH PISTON
| *1 | O-Ring | *2 | D-Ring |
Install the forward clutch drum sub-assembly to the stator (CVT) shaft assembly.
Apply compressed air (approximately 250 kPa (2.5 kgf/cm2, 36 psi)) to the fluid hole of the stator (CVT) shaft assembly to separate the forward clutch piston from the forward clutch drum sub-assembly.
Be careful as fluid may spray when applying compressed air.
Remove the forward clutch piston from the forward clutch drum sub-assembly.
Remove the O-ring and D-ring from the forward clutch piston.
Remove the forward clutch drum sub-assembly from the stator (CVT) shaft assembly.
50.REMOVE CLUTCH DRUM OIL SEAL RING
|
|
Remove the 2 clutch drum oil seal rings from the stator (CVT) shaft assembly.
35720M
51.REMOVE PLANETARY GEAR ASSEMBLY
Remove the planetary gear assembly from the front planetary ring gear sub-assembly.
Remove the thrust needle roller bearing from the planetary gear assembly.
35075D
52.REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY
Remove the thrust needle roller bearing from the front planetary ring gear sub-assembly.
Remove the front planetary ring gear sub-assembly from the transaxle case sub-assembly.
35726A
53.REMOVE PLANETARY RING GEAR THRUST WASHER
35681B
54.REMOVE NO. 1 BRAKE DISC
| *1 | Brake Flange | *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate | *4 | Brake Cushion Plate |
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.
Be careful not to damage the transaxle case sub-assembly.
Remove the brake flange, 3 No. 1 brake discs, 3 No. 1 brake plates and brake cushion plate from the transaxle case sub-assembly.
55.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.
Do not compress the 1st and reverse brake return spring sub-assembly excessively.
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.
Be careful not to damage the transaxle case sub-assembly.
Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.
35623L
56.REMOVE REVERSE BRAKE PISTON
Apply compressed air (approximately 250 kPa (2.5 kgf/cm2, 36 psi)) to the fluid hole to disconnect the reverse brake piston from the transaxle case sub-assembly.
Be careful as fluid may spray when applying compressed air.
Remove the reverse brake piston from the transaxle case sub-assembly.
Remove the 2 O-rings from the reverse brake piston.
57.REMOVE REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the reduction driven gear rear tapered roller bearing (outer race) from the transaxle case sub-assembly.
Align the claw of SST with the indentation of the transaxle case sub-assembly when removing the parts.
58.REMOVE DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the differential case rear tapered roller bearing (outer race) from the transaxle case sub-assembly.
Align the claw of SST with the indentation of the transaxle case sub-assembly when removing the parts.
43420H
59.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST and a hammer, remove the front drive shaft oil seal LH from the transaxle case sub-assembly.
60.REMOVE STRAIGHT PIN
61.REMOVE REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold | *b | Turn |
Using SST, remove the reduction driven gear rear tapered roller bearing (inner race) from the reduction driven gear.
Because SST is attached to the roller portion, there is a possibility that the roller portion could break and SST could come off before the reduction driven gear rear tapered roller bearing (inner race) comes off.
If the roller portion breaks and SST comes off, reattach SST to the inner race in the position shown in the illustration, and continue removing the parts.
62.REMOVE REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold | *b | Turn |
Using SST, remove the reduction driven gear front tapered roller bearing (inner race) from the reduction driven gear.
63.REMOVE DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold | *b | Turn |
Using SST, remove the differential case rear tapered roller bearing (inner race) from the differential case sub-assembly.
64.REMOVE DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold | *b | Turn |
Using SST, remove the differential case front tapered roller bearing (inner race) from the differential case sub-assembly.