Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE UNIT
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438028 CONTINUOUSLY VARIABLE TRANSAXLE UNIT A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C446629N01
2.417,0.563 2.667,0.26 2.667,0.26 2.833,0.26 false 4.24,4.354 4.573,4.354 false 4.281,2.385 4.156,2.219 4.156,2.219 3.99,2.219 false 3.469,2.708 3.969,2.708 false 2.563,2.208 2.875,1.896 2.875,1.896 3.042,1.896 false 6.469,0.188 6.802,0.188 false 1.75,3.417 2.292,3.417 false 3.823,2.135 4.208,2.385 0.385,0.25 10 false *1 2.469,0.479 2.896,0.708 0.427,0.229 10 false x2 3.115,0.156 3.323,0.531 0.208,0.375 18 false 2 3.396,1.792 3.594,2.094 0.198,0.302 18 false 5 3.146,2.615 3.531,2.865 0.385,0.25 10 false ● 6.021,0.042 6.521,0.417 0.5,0.375 18 false 1, 7 4.823,4.26 5.208,4.51 0.385,0.25 10 false ● 3.281,2.573 3.479,2.875 0.198,0.302 18 false 6 1.563,3.281 1.771,3.656 0.208,0.375 18 false 4 4.958,4.24 5.156,4.542 0.198,0.302 18 false 3 1.438,3.333 1.823,3.583 0.385,0.25 10 false ● 3.281,1.823 3.667,2.073 0.385,0.25 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BEARING POSITION - (Click here) - -
2 STRAIGHT PIN - (Click here) - -
3 DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE) - (Click here) - -
4 DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE) - (Click here) - -
5 DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) - (Click here) - -
6 DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) - (Click here) - -
7 DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD - (Click here) - -

*1 SHIM - -
● Non-reusable part - -

C446630N01
1.875,0.594 2.208,0.594 false 4,1.51 4.167,1.51 4.167,1.51 4.25,1.76 false 4.042,4.208 4.375,4.208 false 2.167,3.531 2.667,3.531 false 6.479,0.198 6.813,0.198 false 3.615,2.531 3.781,2.531 3.781,2.531 4,2.094 false 4.656,4.104 5.042,4.354 0.385,0.25 10 false ● 3.865,1.427 4.292,1.656 0.427,0.229 10 false *1 4.771,4.052 5.104,4.448 0.333,0.396 18 false 8 2.01,3.385 2.344,3.781 0.333,0.396 18 false 9 1.896,3.458 2.281,3.708 0.385,0.25 10 false ● 2.469,0.5 2.854,0.75 0.385,0.25 10 false ● 2.573,0.448 2.906,0.844 0.333,0.396 18 false 10 3.313,2.396 3.646,2.792 0.333,0.396 18 false 11 3.208,2.438 3.594,2.688 0.385,0.25 10 false ● 6.146,0.052 6.479,0.448 0.333,0.396 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

8 REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE) - (Click here) - -
9 REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE) - (Click here) - -
10 REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE) - (Click here) - -
11 REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE) - (Click here) - -
12 REDUCTION DRIVEN GEAR TAPERED ROLLER BEARING PRELOAD - (Click here) - -

*1 SHIM - -
● Non-reusable part - -

C446631N01
5.604,2.823 5.938,2.823 false 3.063,5.5 3.563,5.5 false 5.052,2.042 5.302,1.667 5.302,1.667 5.469,1.667 false 4.5,1.708 4.708,1.354 4.708,1.354 4.875,1.354 false 3.521,1.198 3.521,0.615 3.521,0.615 4.26,0.615 false 3.917,0.625 3.917,1.542 false 5.146,1.24 5.698,1.594 0.552,0.354 18 false 14 5.74,1.563 6.292,1.917 0.552,0.354 18 false 15 2.76,5.354 3.313,5.708 0.552,0.354 18 false 13 4.333,0.521 4.49,0.719 0.156,0.198 10 false ● 6,2.719 6.24,2.917 0.24,0.198 10 false *1 2.656,5.406 2.813,5.604 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

13 FRONT DRIVE SHAFT OIL SEAL LH 43420H (Click here) - -
14 REVERSE BRAKE PISTON 35623L (Click here) - -
15 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY - (Click here) - -

*1 SNAP RING - -
● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE

C446632N01
3,3.417 3,2.917 false 4.333,4.833 2.417,4.833 2.417,4.833 2.417,4.583 false 3.083,4.833 3.083,4.25 false 3.583,4.833 3.583,3.917 false 4.406,3.802 4.406,3.469 false 1.906,5.24 1.906,4.906 false 1.344,5.563 1.344,5.229 false 3.667,3.083 3.667,2.917 3.667,2.917 2.25,2.917 false 2.427,3.75 2.427,2.917 false 0.677,1.917 1.01,1.917 false 1.344,1.177 1.51,1.177 1.51,1.177 1.615,1.552 false 2.25,0.396 2.417,0.396 2.417,0.396 2.635,0.708 false 1.979,0.813 2.146,0.813 2.146,0.813 2.323,1.094 false 2.698,0.167 2.865,0.167 2.865,0.167 3.135,0.625 false 2.406,0.042 2.958,0.396 0.552,0.354 18 false 17 1.938,0.292 2.49,0.646 0.552,0.354 18 false 18 1,1.052 1.552,1.406 0.552,0.354 18 false 19 4.615,4.708 5.167,5.063 0.552,0.354 18 false 16 1.281,5.604 1.594,5.802 0.313,0.198 10 false *2 1.844,5.292 2.156,5.49 0.313,0.198 10 false *3 0.479,1.802 0.792,2 0.313,0.198 10 false *1 2.063,2.823 2.375,3.021 0.313,0.198 10 false *4 4.354,3.854 4.667,4.052 0.313,0.198 10 false *5 1.781,0.719 2.094,0.917 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

16 NO. 1 BRAKE DISC 35681B (Click here) - -
17 PLANETARY RING GEAR THRUST WASHER 35726A - - -
18 FRONT PLANETARY RING GEAR SUB-ASSEMBLY 35075D (Click here) - -
19 PLANETARY GEAR ASSEMBLY 35720M (Click here) - -

*1 THRUST NEEDLE ROLLER BEARING *2 SNAP RING
*3 BRAKE FLANGE *4 NO. 1 BRAKE PLATE
*5 BRAKE CUSHION PLATE - -
V100135

Toyota Genuine CVT Fluid FE - -

C446824N01
0.729,1.01 1.042,1.01 false 2.396,0.979 2.594,0.49 2.594,0.49 2.76,0.49 false 2.896,1.125 3.094,0.635 3.094,0.635 3.26,0.635 false 3.75,1.406 3.958,0.896 3.958,0.896 4.125,0.896 false 4.313,1.938 4.521,1.427 4.521,1.427 4.688,1.427 false 5.802,2.698 6.042,2.177 6.042,2.177 6.208,2.177 false 6.188,3.281 6.5,3.281 false 4.729,5.198 5.042,5.198 false 3.292,5.458 3.292,5.188 false 2.656,3.781 2.656,2.917 2.656,2.917 1.01,2.917 false 1.99,3.406 1.99,2.917 false 1.302,3.052 1.302,2.917 false 2.74,4.781 2.74,5.156 2.74,5.156 0.74,5.156 false 1.948,5.146 1.948,4.385 false 1.323,5.156 1.323,4.031 false 4.938,2.24 5.104,1.813 5.104,1.813 5.271,1.813 false 2.844,0.385 3.104,0.594 0.26,0.208 10 false ● 0.563,0.917 0.823,1.125 0.26,0.208 10 false *4 3.333,0.531 3.594,0.74 0.26,0.208 10 false ● 4.479,0.729 4.938,1.156 0.458,0.427 18 false 20 4.781,1.25 5.24,1.677 0.458,0.427 18 false 21 6.573,2 7.031,2.354 0.458,0.354 18 false 22 0.406,5.021 0.865,5.375 0.458,0.354 18 false 23 6.552,3.167 6.813,3.375 0.26,0.208 10 false *1 5.115,5.083 5.375,5.292 0.26,0.208 10 false *1 3.208,5.5 3.469,5.708 0.26,0.208 10 false *2 0.833,2.823 1.094,3.031 0.26,0.208 10 false *3 5.323,1.708 5.583,1.917 0.26,0.208 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

20 FORWARD CLUTCH PISTON 35612D (Click here) - -
21 FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY 35603E - - -
22 NO. 1 CLUTCH BALANCER - (Click here) - -
23 FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC 35633H (Click here) - -

*1 SNAP RING *2 FORWARD CLUTCH FLANGE
*3 FORWARD MULTIPLE DISC CLUTCH CLUTCH PLATE *4 FORWARD CLUTCH DRUM SUB-ASSEMBLY
● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE

C446633N01
4.5,3.25 5.25,3.417 0.75,0.167 4.5,3.917 5.333,4.083 0.833,0.167 4.458,3.875 5.375,4.125 0.917,0.25 4.458,3.208 5.281,3.458 0.823,0.25 0.958,3.042 1.323,3.042 false 3.927,4.021 4.26,4.021 false 3.896,3.333 4.229,3.333 false 2.323,4.083 2.625,4.083 false 3.802,2.5 4.135,2.5 false 3.479,2.833 3.813,2.833 false 3.667,3.615 4,3.615 false 0.677,2.896 1.052,3.208 0.375,0.313 18 false 27 4.146,2.688 4.552,2.979 0.406,0.292 18 false 24 4.177,2.396 4.5,2.667 0.323,0.271 10 false *1 4.542,3.25 5.469,3.448 0.927,0.198 8 false 10.5 (107, 8) 4.552,3.917 5.406,4.135 0.854,0.219 8 false 15.7 (160, 12) 4.292,3.938 4.448,4.135 0.156,0.198 10 false ★ 4.281,3.25 4.438,3.448 0.156,0.198 10 false ★ 4.292,3.479 4.698,3.771 0.406,0.292 18 false 26 2.031,3.948 2.438,4.24 0.406,0.292 18 false 25

Procedure Part Name Code
Z101186

Z101188

Z101187

24 FORWARD MULTIPLE DISC CLUTCH ASSEMBLY 35610A (Click here) - -
25 STAY - (Click here) - -
26 NO. 1 GEAR SHIFT FORK ASSEMBLY 33210A (Click here) - -
27 1ST GEAR SUB-ASSEMBLY 33032 (Click here) - -

*1 THRUST BEARING RACE - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100135

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
★ Precoated part - -

C446634N01
1.927,4.115 7.031,5.75 5.104,1.635 3.76,0.792 4.844,0.958 1.083,0.167 6.167,2.396 7,2.563 0.833,0.167 6.083,5 6.917,5.167 0.833,0.167 2.135,5.5 3.219,5.667 1.083,0.167 3.427,0.865 3.76,0.865 false 3.052,0.542 3.385,0.542 false 5.667,2.469 6.167,2.469 false 5.406,3.135 5.99,3.135 5.99,3.135 5.99,2.469 false 3.917,2.583 3.917,2.083 false 4.75,3.333 4.75,3 false 3.917,2.333 4.167,2.333 4.167,2.333 4.167,2.167 false 2.479,3.802 2.813,3.802 false 5.406,4.385 5.74,4.385 false 4.313,4.885 4.469,5.031 4.469,5.031 4.635,5.031 false 5.333,5.073 6.083,5.073 false 5.802,5.073 5.802,4.906 false 4.083,5.49 4.417,5.49 false 2.708,5.5 2.708,5.333 2.708,5.333 3.125,5.333 false 1.583,4.938 1.917,4.938 false 3.448,0.385 3.865,0.729 0.417,0.344 18 false 30 3.969,2.573 4.385,2.917 0.417,0.344 18 false 28 4.906,3.396 5.323,3.74 0.417,0.344 18 false 29 4.698,5.385 5.115,5.729 0.417,0.344 18 false 31 1.271,4.802 1.688,5.146 0.417,0.344 18 false 32 2.313,3.677 2.469,3.875 0.156,0.198 10 false ● 5.333,3.188 5.646,3.385 0.313,0.198 10 false x2 5.604,2.51 5.917,2.708 0.313,0.198 10 false x5 5.281,5.083 5.594,5.281 0.313,0.198 10 false x2 5.885,4.792 6.198,4.99 0.313,0.198 10 false x2 3.208,5.313 3.521,5.51 0.313,0.198 10 false x2 3.438,0.906 3.75,1.104 0.313,0.198 10 false x2 3.823,0.792 4.979,0.948 1.156,0.156 8 false 9.8 (100, 87 in.*lbf) 6.24,2.406 7.156,2.563 0.917,0.156 8 false 29.4 (300, 22) 5.802,4.292 6.115,4.49 0.313,0.198 10 false *1 4.708,4.938 4.865,5.135 0.156,0.198 10 false ● 6.156,5.01 7.073,5.167 0.917,0.156 8 false 22.1 (225, 16) 2.198,5.51 3.354,5.667 1.156,0.156 8 false 9.8 (100, 87 in.*lbf) 4.76,3.427 4.917,3.625 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

28 CLUTCH DRUM OIL SEAL RING - (Click here) - -
29 STATOR (CVT) SHAFT ASSEMBLY 35370E (Click here) - -
30 NO. 1 TRANSMISSION CASE PLATE 35165B - - -
31 OIL STRAINER ASSEMBLY 35330J (Click here) - -
32 FRONT OIL PUMP ASSEMBLY 35310A (Click here) - -

*1 FRONT OIL PUMP ASSEMBLY - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE - -

C446825N01
5.625,4.083 6.708,4.25 1.083,0.167 4.177,0.385 4.49,0.385 false 4.688,0.74 5.063,0.74 false 4.969,1.115 5.344,1.115 false 4.385,2.01 4.729,2.01 false 5.26,2.573 5.604,2.573 false 4.552,2.417 4.552,2.677 false 4.938,3.51 5.281,3.51 false 3.979,4.927 4.323,4.927 false 3.031,3.781 3.031,4.042 false 5.271,4.156 5.615,4.156 false 5.396,0.573 5.948,0.927 0.552,0.354 18 false 34 5.677,2.396 6.229,2.75 0.552,0.354 18 false 36 5.031,1.875 5.583,2.229 0.552,0.354 18 false 35 5.323,3.344 5.875,3.698 0.552,0.354 18 false 33 2.875,4.063 3.427,4.417 0.552,0.354 18 false 38 4.385,4.771 4.938,5.125 0.552,0.354 18 false 37 4.469,2.708 5.021,3.063 0.552,0.354 10 false *3 4.521,0.281 5.073,0.635 0.552,0.354 10 false *2 5.385,1.01 5.938,1.365 0.552,0.354 10 false *1 5.24,4.167 5.792,4.521 0.552,0.354 10 false x2 5.677,4.094 6.75,4.271 1.073,0.177 8 false 9.8 (100, 87 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

33 NO. 1 TRANSMISSION OIL PUMP SEPARATE PLATE 35316A - - -
34 DRIVEN SPROCKET 35783N (Click here) - -
35 DRIVE SPROCKET 35782P (Click here) - -
36 NO. 2 TRANSMISSION OIL PUMP SEPARATE PLATE 35317A - - -
37 DIFFERENTIAL CASE SUB-ASSEMBLY - - - -
38 REDUCTION DRIVEN GEAR 35759A - - -

*1 THRUST NEEDLE ROLLER BEARING *2 TRANSMISSION DRIVE CHAIN
*3 SNAP RING - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

C434376N01
1.75,2.74 2.115,2.74 false 2.521,3.885 2.781,3.885 false 1.302,2.625 1.615,2.833 0.313,0.208 10 false ● 2.073,3.771 2.281,4.052 0.208,0.281 10 false ● 1.438,2.583 2.135,3.031 0.698,0.448 18 false 40 2.208,3.729 2.906,4.177 0.698,0.448 18 false 39

Procedure Part Name Code
Z101186

Z101188

Z101187

39 CVT TYPE T OIL SEAL - (Click here) - -
40 FRONT DRIVE SHAFT OIL SEAL RH 43410M (Click here) - -

● Non-reusable part
V100135

MP grease

C446635N01
0.948,3.083 2.031,3.25 1.083,0.167 0.906,3.042 2.073,3.292 1.167,0.25 2.917,1.323 3.25,1.323 false 2.844,1.729 3.177,1.729 false 2.271,2 2.438,2 2.438,2 2.646,2.063 false 2.958,2.333 3.292,2.333 false 2.313,2.688 2.646,2.688 false 2.031,3.177 2.365,3.177 false 2.656,2.198 3.208,2.552 0.552,0.354 18 false 41 2.552,1.167 3.104,1.521 0.552,0.354 18 false 42 1.958,1.885 2.51,2.24 0.552,0.354 18 false 43 1.979,2.542 2.531,2.896 0.552,0.354 18 false 44 2.667,1.646 2.979,1.844 0.313,0.198 10 false *1 2.448,3.229 2.76,3.427 0.313,0.198 10 false x2 1.021,3.073 2.073,3.26 1.052,0.188 8 false 9.8 (100, 87 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

41 PARKING LOCK SLEEVE 35598B - - -
42 PARKING LOCK PAWL 35557C - - -
43 PARKING LOCK PAWL SHAFT 35556N (Click here) - -
44 CAM GUIDE SLEEVE 35593A - - -

*1 TORSION SPRING - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -

C446636N01
2.042,4.469 3.125,4.635 1.083,0.167 1.219,3.792 2.219,3.958 1,0.167 1.229,2.083 1.417,2.083 1.417,2.083 1.5,2.615 false 2.021,2.938 2.021,2.521 false 2.698,2.552 2.698,2.021 false 0.667,2.979 1,2.979 false 3.125,4.552 3.458,4.552 false 2.229,3.865 2.583,3.865 false 3.26,2.229 3.26,1.74 false 3.552,3.417 3.917,3.417 false 4.24,5.281 4.24,4.896 false 4.948,4.792 4.948,4.406 false 4.115,5.313 4.51,5.656 0.396,0.344 18 false 49 4.844,4.823 5.25,5.208 0.406,0.385 18 false 48 3.99,3.281 4.448,3.583 0.458,0.302 18 false 47 0.927,1.948 1.292,2.25 0.365,0.302 18 false 46 2.708,2.51 3.125,2.823 0.417,0.313 18 false 45 0.49,2.885 0.792,3.125 0.302,0.24 10 false *1 3.5,4.583 3.802,4.823 0.302,0.24 10 false x3 5.021,4.302 5.323,4.542 0.302,0.24 10 false x3 1.281,3.802 2.302,4 1.021,0.198 8 false 5.4 (55, 48 in.*lbf) 2.104,4.479 3.219,4.708 1.115,0.229 8 false 9.8 (100, 87 in.*lbf) 1.979,2.948 2.333,3.146 0.354,0.198 10 false ● 3.229,2.25 3.583,2.448 0.354,0.198 10 false ● 2.667,3.854 2.969,4.094 0.302,0.24 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

45 C-2 CLUTCH PRESSURE APPLY TUBE SUB-ASSEMBLY 35809 (Click here) - -
46 SECONDARY SHAFT LUBE APPLY TUBE 35896A (Click here) - -
47 DIFFERENTIAL GEAR LUBE APPLY TUBE 35882E - - -
48 OIL CLEANER(CVT) MAGNET 35394D - - -
49 OIL RESERVOIR LOCK PLATE 35174B - - -

*1 SNAP RING
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE - -

C446637N01
0.115,2.198 0.948,2.365 0.833,0.167 0.948,2.281 1.281,2.281 false 1.625,2.833 2.125,2.833 false 4.844,3.25 4.844,2.917 false 1.417,2.229 1.844,2.438 0.427,0.208 10 false x20 0.167,2.198 0.969,2.406 0.802,0.208 8 false 29.4 (300, 22) 1.323,2.698 1.802,3.115 0.479,0.417 18 false 50 4.927,2.865 5.26,3.083 0.333,0.219 10 false x5 4.802,3.281 5.323,3.521 0.521,0.24 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

50 TRANSAXLE HOUSING 35111C (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE - -

C446638N01
2.74,4.198 3.74,4.365 1,0.167 3.458,0.198 4.458,0.365 1,0.167 0.969,2.167 1.719,2.333 0.75,0.167 0.26,4.24 1.01,4.406 0.75,0.167 0.177,5.188 0.927,5.354 0.75,0.167 3.115,0.271 3.448,0.271 false 2.458,0.51 2.792,0.51 false 6.156,3.667 6.156,3.333 false 4.375,4.833 4.375,4.5 false 3.677,3.865 3.51,3.865 3.51,3.865 3.344,3.531 false 3.229,4.198 3.229,4.031 3.229,4.031 2.927,3.646 false 2.469,4.906 2.802,4.906 false 2.438,1.979 2.104,1.813 2.104,1.813 1.938,1.813 false 1.729,2.25 2.063,2.25 false 2.667,1.708 2.573,2.521 2.573,2.521 2.406,2.521 false 1.021,4.313 1.354,4.313 false 0.938,5.271 1.354,5.271 false 1.604,5.448 1.104,5.448 1.104,5.448 1.104,5.281 false 3.75,3.708 4.302,4.063 0.552,0.354 18 false 51 2.125,0.375 2.677,0.729 0.552,0.354 18 false 52 3.094,4.781 3.646,5.135 0.552,0.354 18 false 53 6.219,3.26 6.531,3.458 0.313,0.198 10 false x3 6.125,3.667 6.438,3.865 0.313,0.198 10 false ● 4.344,4.844 4.656,5.042 0.313,0.198 10 false ● 2.781,4.208 3.844,4.458 1.063,0.25 8 false 5.4 (55, 48 in.*lbf) 3.5,0.198 4.563,0.448 1.063,0.25 8 false 5.4 (55, 48 in.*lbf) 1.76,1.708 2.073,1.906 0.313,0.198 10 false *1 1.01,2.167 1.823,2.333 0.813,0.167 8 false 10.8 (110, 8) 2.26,2.396 2.573,2.594 0.313,0.198 10 false ● 0.313,4.24 1.125,4.406 0.813,0.167 8 false 10.8 (110, 8) 0.219,5.198 1.031,5.365 0.813,0.167 8 false 10.8 (110, 8) 1.719,5.417 2.031,5.615 0.313,0.198 10 false x5 1.458,5.24 1.771,5.438 0.313,0.198 10 false x5

Procedure Part Name Code
Z101186

Z101188

Z101187

51 TRANSMISSION REVOLUTION SENSOR (NC1) 89413S - - -
52 TRANSMISSION WIRE 82125M (Click here) - -
53 TRANSMISSION VALVE BODY ASSEMBLY 35410J (Click here) - -

*1 TEMPERATURE SENSOR CLAMP - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE - -

C446639N01
0.25,3.417 1.25,3.583 1,0.167 5.531,3.771 6.448,3.938 0.917,0.167 4.479,4.25 5.229,4.417 0.75,0.167 5.656,3.146 6.406,3.313 0.75,0.167 4.438,4.208 5.271,4.458 0.833,0.25 0.208,3.375 1.292,3.625 1.083,0.25 5.615,3.104 6.448,3.354 0.833,0.25 1.063,2.833 0.75,3.25 0.75,3.25 0.75,3.417 false 4.833,4.26 4.833,3.917 false 2.396,3.74 2.729,3.74 false 4.5,3.635 4.833,3.635 false 5.573,2.479 5.76,2.135 5.76,2.135 5.927,2.135 false 2.75,2.615 2.75,2.948 false 4.875,3.417 5.354,3.854 5.354,3.854 5.521,3.854 false 5.771,2.646 6.031,2.969 6.031,2.969 6.031,3.135 false 2.719,2.938 3.073,3.135 0.354,0.198 10 false ● 1.188,2.833 1.583,3.073 0.396,0.24 10 false x11 0.292,3.417 1.313,3.625 1.021,0.208 8 false 7.4 (75, 65 in.*lbf) 5.729,3.146 6.531,3.344 0.802,0.198 8 false 49 (500, 36) 5.604,3.781 6.49,3.99 0.885,0.208 8 false 0.8 (8, 7 in.*lbf) 3.167,3.625 3.51,3.979 0.344,0.354 18 false 54 4.375,3.542 4.563,3.74 0.188,0.198 10 false ● 5.958,2.052 6.313,2.229 0.354,0.177 10 false ● 4.552,4.26 5.354,4.458 0.802,0.198 8 false 49 (500, 36) 5.667,4.188 6.01,4.542 0.344,0.354 18 false 56 6.771,3.708 7.115,4.063 0.344,0.354 18 false 55 6.76,3.125 7.104,3.479 0.344,0.354 18 false 57 3.031,3.656 3.385,3.854 0.354,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

54 TRANSAXLE SIDE COVER SUB-ASSEMBLY 35015Y (Click here) - -
55 OVERFLOW (CVT) TUBE 35125E (Click here) - -
56 OVERFLOW PLUG 35125G (Click here) - -
57 REFILL PLUG - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE

C446640N01
0.24,2.802 1.24,2.969 1,0.167 4.99,3.229 5.823,3.396 0.833,0.167 5.448,2.24 6.448,2.406 1,0.167 1.573,2.885 1.24,2.885 false 5.917,1.906 5.917,2.24 false 5.396,2.906 5.396,3.229 false 2.031,2.708 2.031,3.042 false 5.885,1.583 5.552,1.583 false 1.74,1.99 1.906,1.99 1.906,1.99 2.177,2.427 false 5.667,1.167 5.5,1.167 5.5,1.167 5.271,1.563 false 1.927,3.073 2.385,3.396 0.458,0.323 18 false 60 6.167,1.458 6.74,1.865 0.573,0.406 18 false 59 1.563,1.885 1.958,2.073 0.396,0.188 10 false ● 0.292,2.802 1.344,3 1.052,0.198 8 false 5.4 (55, 48 in.*lbf) 5.51,2.26 6.563,2.458 1.052,0.198 8 false 5.4 (55, 48 in.*lbf) 5.063,3.25 5.979,3.479 0.917,0.229 8 false 20.6 (210, 15) 5.729,1.063 6.125,1.25 0.396,0.188 10 false ● 6.156,3.188 6.729,3.594 0.573,0.406 18 false 58

Procedure Part Name Code
Z101186

Z101188

Z101187

58 OIL PRESSURE SENSOR 89637K (Click here) - -
59 TRANSMISSION REVOLUTION SENSOR (NSS) 89413T (Click here) - -
60 TRANSMISSION REVOLUTION SENSOR (NT) 89413N - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE - -

C446641N01
0.167,4.333 0.833,4.5 0.667,0.167 4.833,1 5.833,1.167 1,0.167 1.729,0.667 2.729,0.833 1,0.167 0.854,1.083 1.854,1.25 1,0.167 3.25,0.219 4,0.385 0.75,0.167 4.792,0.958 5.875,1.208 1.083,0.25 0.125,4.292 0.875,4.542 0.75,0.25 3.208,0.177 4.042,0.427 0.833,0.25 0.833,4.417 1,4.417 1,4.417 1.083,4.75 false 1.031,3.833 1.198,3.833 1.198,3.833 1.5,4.24 false 2.781,5.167 2.781,4.646 false 6.094,2.333 6.427,2.333 false 1.75,1.5 2.083,1.5 false 3.198,1.052 3.5,1.052 false 4.5,0.698 4.833,0.698 false 4.448,0.5 4.781,0.5 false 4,0.313 4.333,0.313 false 4.5,1.083 4.833,1.083 false 2.5,4.385 2.5,5.167 2.5,5.167 2.865,5.167 false 3.198,1.365 3.531,1.365 false 1.854,1.167 2.188,1.167 false 2.729,0.75 3.063,0.75 false 4.667,1.438 5,1.438 false 0.729,3.698 1.167,4.125 0.438,0.427 18 false 65 5.302,1.333 5.74,1.719 0.438,0.385 18 false 64 1.438,1.354 1.875,1.698 0.438,0.344 18 false 63 3.802,0.927 4.188,1.271 0.385,0.344 18 false 62 4.833,0.417 5.125,0.635 0.292,0.219 10 false *1 4.865,0.615 5.135,0.802 0.271,0.188 10 false *2 0.198,4.344 0.958,4.563 0.76,0.219 8 false 21 (214, 15) 1.177,4.719 1.469,4.969 0.292,0.25 10 false x3 4.542,1.094 4.833,1.344 0.292,0.25 10 false x2 4.885,1.01 5.885,1.208 1,0.198 8 false 5.4 (55, 48 in.*lbf) 2.906,5.063 3.333,5.333 0.427,0.271 10 false ● 1.781,0.667 2.781,0.865 1,0.198 8 false 5.4 (55, 48 in.*lbf) 0.896,1.094 1.896,1.292 1,0.198 8 false 5.4 (55, 48 in.*lbf) 3.292,0.219 4.083,0.427 0.792,0.208 8 false 12.7 (130, 9) 3.563,1.26 3.99,1.531 0.427,0.271 10 false ● 6.5,2.188 6.844,2.51 0.344,0.323 18 false 61 6.458,1.208 6.75,1.458 0.292,0.25 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

61 AUTOMATIC TRANSMISSION CASE COVER 35151K - - -
62 TRANSMISSION REVOLUTION SENSOR (NOUT) 89413M (Click here) - -
63 SHIFT STROKE SENSOR 89419B (Click here) - -
64 PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 (Click here) - -
65 TRANSMISSION OIL COOLER ASSEMBLY 33493C (Click here) - -

*1 WASHER *2 TRANSMISSION CONTROL SHAFT LEVER
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

Toyota Genuine CVT Fluid FE

CAUTION / NOTICE / HINT

NOTICE:
·

Clean the work area, tools to be used, other equipment, etc., thoroughly before performing this procedure, as there is a possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, paper towels, etc., that may produce lint, dust or foreign matter.

·

When cleaning parts, make sure that dust or foreign matter does not enter the CVT.

·

When replacing any tapered roller bearing (inner race) or tapered roller bearing (outer race), replace both the tapered roller bearing (inner race) and tapered roller bearing (outer race) with new ones.

·

When the tapered roller bearing (inner race) is removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) need to be replaced.

·

When the tapered roller bearing (inner race) is not removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) can be reused.



HINT:

Shift shock may increase after replacing the transmission valve body assembly or forward multiple disc clutch assembly. In this case, shift shock will reduce as the vehicle is driven.


PROCEDURE

Hide 1. BEARING POSITION

a.
C432758N01
2.75,3.354 2.948,3.604 0.198,0.25 10 false A 2.188,7.51 2.385,7.76 0.198,0.25 10 false B 3.604,6.729 3.802,6.979 0.198,0.25 10 false C

i.

Check the position and installation direction of each bearing.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter
Mark Thrust Bearing Race Diameter Inside / Outside
mm (in.)
Thrust Needle Roller Bearing Diameter Inside / Outside
mm (in.)
A - 47.75 (1.88) / 65.8 (2.59)
B 26.38 (1.04) / 38.9 (1.53) 24.9 (0.98) / 38.9 (1.53)
C - 29.7 (1.17) / 49.1 (1.93)



Hide 2.INSTALL STRAIGHT PIN

a.
C446643N01
0.49,0.156 0.771,0.51 0.281,0.354 18 false i

i.

Install the 2 straight pins to the transaxle case sub-assembly.

Protrusion Height:

7.0 to 8.0 mm (0.276 to 0.315 in.)




Hide 3.INSTALL DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C446644N01
3,1.604 3.333,1.604 false 0.479,0.177 0.76,0.531 0.281,0.354 18 false i 2.615,1.51 2.958,1.688 0.344,0.177 10 true SST

i.

Using SST and a press, install a new differential case rear tapered roller bearing (inner race) to the differential case sub-assembly.

SST
09223-00010  

NOTICE:
·

Do not damage the differential case rear tapered roller bearing (inner race) cage when installing the differential case rear tapered roller bearing (inner race).

·

Be sure to install the differential case rear tapered roller bearing (inner race) so that there is no clearance between the differential case rear tapered roller bearing (inner race) and the differential case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.





Hide 4.INSTALL DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C446645N01
3.031,1.656 3.365,1.656 false 2.625,1.542 2.979,1.74 0.354,0.198 10 true SST 0.479,0.156 0.76,0.51 0.281,0.354 18 false i

i.

Using SST and a press, install a new differential case front tapered roller bearing (inner race) to the differential case sub-assembly.

SST
09309-37010  

NOTICE:
·

Do not damage the differential case front tapered roller bearing (inner race) cage when installing the differential case front tapered roller bearing (inner race).

·

Be sure to install the differential case front tapered roller bearing (inner race) so that there is no clearance between the differential case front tapered roller bearing (inner race) and the differential case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.





Hide 5.INSTALL DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C446646N01
2.938,1.26 2.25,1.021 2.25,1.021 3.042,1.115 true 0.438,0.104 0.719,0.458 0.281,0.354 18 false i 1.948,0.917 2.406,1.115 0.458,0.198 10 false SST

i.

Using SST and a hammer, install a new differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60021  (09951-00680)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the differential case rear tapered roller bearing (outer race) so that there is no clearance between the differential case rear tapered roller bearing (outer race) and the transaxle case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.




Hide 6.INSTALL DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C446647N01
0.448,0.177 0.729,0.531 0.281,0.354 18 false i 3.76,0.219 4.042,0.573 0.281,0.354 18 false ii

i.

Install the shim to the transaxle housing.


ii.

Using SST and a hammer, install a new differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60011  (09951-00650)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the differential case front tapered roller bearing (outer race) so that there is no clearance between the differential case front tapered roller bearing (outer race), shim and the transaxle housing. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.




Hide 7.ADJUST DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD

a.
C446648N01
0.677,4.156 1.594,4.156 true 4.323,4.167 5.24,4.167 true 0.427,0.115 1.313,0.396 0.885,0.281 18 false i, ii, vii 3.583,0.104 4.271,0.385 0.688,0.281 18 false iii, vi 0.656,2.927 0.969,3.219 0.313,0.292 18 false iv 4.083,2.969 4.396,3.26 0.313,0.292 18 false v 0.344,4.063 0.802,4.26 0.458,0.198 10 false SST 4.01,4.083 4.469,4.281 0.458,0.198 10 false SST

i.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.

NOTICE:

Make sure that there is no Toyota Genuine CVT fluid FE on the contact surfaces.



ii.

Install the differential case sub-assembly to the transaxle case sub-assembly.


iii.

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


iv.

Using SST, turn the differential case sub-assembly right and left 2 or 3 times to settle the bearings.

SST
09564-32011  


v.

Using SST and a torque wrench, measure the turning torque of the differential case tapered roller bearing while rotating SST at 10 rpm.

SST
09564-32011  

Standard Turning Torque:

1.61 to 2.57 N*m (17 to 26 kgf*cm, 15 to 22 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness:
Part Number Thickness
mm (in.)
90564-58002 1.76 (0.0693)
90564-58003 1.79 (0.0705)
90564-58004 1.82 (0.0717)
90564-58005 1.85 (0.0728)
90564-58006 1.88 (0.0740)
90564-58007 1.91 (0.0752)
90564-58008 1.94 (0.0764)
90564-58009 1.97 (0.0776)
90564-58010 2.00 (0.0787)
90564-58011 2.03 (0.0799)
90564-58012 2.06 (0.0811)
90564-58013 2.09 (0.0823)
90564-58014 2.12 (0.0835)
90564-58015 2.15 (0.0846)
90564-58016 2.18 (0.0858)
90564-58017 2.21 (0.0870)
90564-58018 2.24 (0.0882)
90564-58019 2.27 (0.0894)
90564-58020 2.30 (0.0906)
90564-58021 2.33 (0.0917)



vi.

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


vii.

Remove the differential case sub-assembly from the transaxle case sub-assembly.



Hide 8.INSTALL REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C446649N01
3.198,1.573 3.448,1.573 false 0.479,0.146 0.76,0.5 0.281,0.354 18 false i 2.885,1.49 3.344,1.688 0.458,0.198 10 false SST

i.

Using SST and a press, install a new reduction driven gear rear tapered roller bearing (inner race) to the reduction driven gear.

SST
09325-40010  

NOTICE:
·

Do not damage the reduction driven gear rear tapered roller bearing (inner race) cage when installing the reduction driven gear rear tapered roller bearing (inner race).

·

Be sure to install the reduction driven gear rear tapered roller bearing (inner race) so that there is no clearance between the reduction driven gear rear tapered roller bearing (inner race) and the reduction driven gear. If there is any clearance, the turning torque of the reduction driven gear cannot be measured correctly.





Hide 9.INSTALL REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C446650N01
3.417,1.969 3.125,1.313 3.125,1.313 3.427,1.583 false 3.563,2.542 4.563,2.542 true 0.479,0.156 0.76,0.51 0.281,0.354 18 false i 2.833,1.198 3.292,1.396 0.458,0.198 10 false SST 4.667,2.448 5.125,2.646 0.458,0.198 10 false SST

i.

Using SST and a press, install a new reduction driven gear front tapered roller bearing (inner race) to the reduction driven gear.

SST
09950-60011  (09951-00300, 09951-00320)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the reduction driven gear front tapered roller bearing (inner race) cage when installing the reduction driven gear front tapered roller bearing (inner race).

·

Be sure to install the reduction driven gear front tapered roller bearing (inner race) so that there is no clearance between the reduction driven gear front tapered roller bearing (inner race) and the reduction driven gear. If there is any clearance, the turning torque of the reduction driven gear cannot be measured correctly.





Hide 10.INSTALL REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C446651N01
3,1.281 2.49,1.031 2.49,1.031 3.094,1.073 true 0.375,0.042 0.656,0.396 0.281,0.354 18 false i 2.198,0.948 2.656,1.146 0.458,0.198 10 false SST

i.

Using SST and a hammer, install a new reduction driven gear rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60011  (09951-00560)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the reduction driven gear rear tapered roller bearing (outer race) so that there is no clearance between the reduction driven gear rear tapered roller bearing (outer race) and the transaxle case sub-assembly. If there is any clearance, the turning torque of the reduction driven gear cannot be measured correctly.




Hide 11.INSTALL REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C446652N01
5.198,1.271 4.042,0.771 4.042,0.771 5.25,1.052 true 0.365,0.042 0.646,0.396 0.281,0.354 18 false i 3.906,0.052 4.188,0.406 0.281,0.354 18 false ii 3.75,0.677 4.208,0.875 0.458,0.198 10 false SST

i.

Install the shim to the transaxle housing.


ii.

Using SST and a hammer, install a new reduction driven gear front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60011  (09951-00500)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the reduction driven gear front tapered roller bearing (outer race) so that there is no clearance between the reduction driven gear front tapered roller bearing (outer race), shim and the transaxle housing. If there is any clearance, the turning torque of the reduction driven gear cannot be measured correctly.




Hide 12.ADJUST REDUCTION DRIVEN GEAR TAPERED ROLLER BEARING PRELOAD

a.
C446653N01
0.427,0.094 0.708,0.448 0.281,0.354 18 false i

i.

Turn the reduction drive gear assembly right and left 2 or 3 times to settle the bearings.



b.
C446654C01
3.917,2.042 5.865,1.135 5.865,1.135 4.479,1.135 true 3.302,0.51 3.656,0.51 false 5.958,1.052 6.417,1.25 0.458,0.198 10 false SST 3.125,0.396 3.438,0.667 0.313,0.271 10 false *a 0.458,0.167 1.833,0.521 1.375,0.354 18 false i, ii
*a SST (Center Bolt) - -


i.

Set SST to the parking lock gear as shown in the illustration.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
09950-60011  (09951-00360, 09951-00250, 09952-06010)

NOTICE:

Do not tighten SST (center bolt) more than is necessary to hold SST in place or the parking lock gear or bearing may unseat.



ii.

Tighten SST (center bolt).

HINT:

Torque: 0.5 N*m (5 kgf*cm, 4 in.*lbf)




c.
C446655N01
0.49,0.167 0.969,0.479 0.479,0.313 18 false i, ii

i.

Using a torque wrench, measure and note the turning torque (T1) of the reduction drive gear assembly while rotating SST at 10 rpm.

HINT:

No specified range is provided for T1 as it is only used for calculating the total preload of the differential case sub-assembly and reduction driven gear.



ii.

Remove SST from the parking lock gear.



d.
C446656N01
0.5,0.219 0.781,0.573 0.281,0.354 18 false i 4.125,0.26 4.406,0.615 0.281,0.354 18 false ii 1.885,2.167 2.167,2.521 0.281,0.354 18 false iii

i.

Install the differential case sub-assembly to the transaxle case sub-assembly.


ii.

Install the reduction driven gear to the transaxle case sub-assembly.


iii.

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)



e.
C446657N01
0.646,1.26 1.896,1.26 true 3.958,1.271 5.208,1.271 true 0.823,0.042 1.104,0.396 0.281,0.354 18 false i 4.177,0.052 4.75,0.354 0.573,0.302 18 false ii, iii 0.323,1.167 0.781,1.365 0.458,0.198 10 false SST 3.604,1.167 4.063,1.365 0.458,0.198 10 false SST

i.

Using SST, turn the differential case sub-assembly right and left 2 or 3 times to settle the bearings.

SST
09564-32011  


ii.

Using a torque wrench, measure and note the turning torque (T2) of the differential case tapered roller bearing while rotating SST at 10 rpm.

SST
09564-32011  


iii.

Subtract T1 from T2 to calculate the total preload of the differential case sub-assembly and reduction driven gear.

Standard Turning Torque:

Differential case tapered roller bearing preload + 2.96 to 5.49 N*m (30 to 56 kgf*cm, 2 to 3 ft.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness:
Part Number Thickness
mm (in.)
Mark
90564-44074 1.71 (0.0673) E
90564-44075 1.74 (0.0685) F
90564-44076 1.77 (0.0697) G
90564-44077 1.80 (0.0709) H
90564-44078 1.83 (0.0720) J
90564-44079 1.86 (0.0732) K
90564-44080 1.89 (0.0744) L
90564-44081 1.92 (0.0756) M
90564-44082 1.95 (0.0768) N
90564-44083 1.98 (0.0780) P
90564-44084 2.01 (0.0791) Q
90564-44085 2.04 (0.0803) R
90564-44086 2.07 (0.0815) S
90564-44087 2.10 (0.0827) T
90564-44088 2.13 (0.0839) U
90564-44089 2.16 (0.0850) V
90564-44090 2.19 (0.0862) W
90564-44091 2.22 (0.0874) X
90564-44092 2.25 (0.0886) Y
90564-44093 2.28 (0.0898) -
90564-44094 2.31 (0.0909) -
90564-44095 2.34 (0.0921) -
90564-44096 2.37 (0.0933) -




f.
C446656N02
1.906,2.208 2.188,2.563 0.281,0.354 18 false i 4.125,0.26 4.406,0.615 0.281,0.354 18 false ii 0.479,0.26 0.76,0.615 0.281,0.354 18 false iii

i.

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


ii.

Remove the reduction driven gear from the transaxle case sub-assembly.


iii.

Remove the differential case sub-assembly from the transaxle case sub-assembly.



Hide 43420H 13.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C446658N01
4.531,2.281 4,1.885 true 0.49,0.167 0.771,0.521 0.281,0.354 18 false i 4.563,2.313 5.021,2.51 0.458,0.198 10 false SST

i.

Using SST and a hammer, install a new front drive shaft oil seal LH to the transaxle case sub-assembly.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.





Hide 35623L 14.INSTALL REVERSE BRAKE PISTON

a.
C446659N01
0.531,0.042 0.813,0.396 0.281,0.354 18 false i 3.563,0.083 3.844,0.438 0.281,0.354 18 false ii

i.

Coat 2 new O-rings with Toyota Genuine CVT fluid FE and install them to the reverse brake piston.

NOTICE:

Ensure that the O-rings is not twisted.



ii.

Install the reverse brake piston to the transaxle case sub-assembly.



Hide 15.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C446660N01
1.813,0.115 2.094,0.469 0.281,0.354 18 false i 0.344,2.083 0.625,2.438 0.281,0.354 18 false ii 3.979,2.073 4.26,2.427 0.281,0.354 18 false iii

i.

Install the 1st and reverse brake return spring sub-assembly to the transaxle case sub-assembly.


ii.

Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.

SST
09223-56010  

NOTICE:

Do not compress the 1st and reverse brake return spring sub-assembly excessively.



iii.

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the transaxle case sub-assembly.

NOTICE:

Be careful not to damage the transaxle case sub-assembly.




Hide 35681B 16.INSTALL NO. 1 BRAKE DISC

a.
C446661C01
3.771,0.542 4.104,0.542 false 4.844,0.979 5.26,0.979 5.26,0.979 5.26,2.313 false 3.771,0.823 3.771,1.573 3.771,1.573 4.104,1.573 false 4.833,1.385 5.25,1.385 false 4.833,1.792 5.25,1.792 false 3.76,1.99 4.094,1.99 false 3.604,0.823 4.104,0.823 false 3.771,1.198 4.104,1.198 false 3.594,0.448 3.906,0.604 0.313,0.156 10 false *1 3.417,0.74 3.729,0.896 0.313,0.156 10 false *2 5.198,2.365 5.51,2.521 0.313,0.156 10 false *3 3.573,1.896 3.885,2.052 0.313,0.156 10 false *4 0.479,0.167 0.76,0.521 0.281,0.354 18 false i
*1 Brake Flange *2 No. 1 Brake Disc
*3 No. 1 Brake Plate *4 Brake Cushion Plate


i.

Install the brake flange, 3 No. 1 brake discs, 3 No. 1 brake plates and brake cushion plate to the transaxle case sub-assembly.



b.
C446662C01
5.49,0.063 5.802,0.26 0.313,0.198 10 false *a 0.438,0.104 0.604,0.406 0.167,0.302 18 false i
*a Snap ring opening within this area. - -


i.

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the transaxle case sub-assembly.

NOTICE:

Be careful not to damage the transaxle case sub-assembly.




Hide 35726A 17.INSTALL PLANETARY RING GEAR THRUST WASHER

a.
C446516


Hide 35075D 18.INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY

a.
C446663N01
0.531,0.094 0.813,0.448 0.281,0.354 18 false i 3.813,0.063 4.094,0.417 0.281,0.354 18 false ii

i.

Install the front planetary ring gear sub-assembly to the transaxle case sub-assembly.


ii.

Coat the thrust needle roller bearing with Toyota Genuine CVT fluid FE and install it to the front planetary ring gear sub-assembly.



Hide 35720M 19.INSTALL PLANETARY GEAR ASSEMBLY

a.
C446664N01
0.375,0.052 0.656,0.406 0.281,0.354 18 false i 3.969,0.073 4.25,0.427 0.281,0.354 18 false ii

i.

Coat the thrust needle roller bearing with Toyota Genuine CVT fluid FE and install it to the planetary gear assembly.


ii.

Install the planetary gear assembly to the front planetary ring gear sub-assembly.



Hide 35612D 20.INSTALL FORWARD CLUTCH PISTON

a.
C446665C01
1.063,0.052 1.344,0.406 0.281,0.354 18 false i 4.604,0.094 4.885,0.448 0.281,0.354 18 false ii 1.698,0.25 2.01,0.448 0.313,0.198 10 false *1 3,1.583 3.313,1.781 0.313,0.198 10 false *2
*1 O-Ring *2 D-Ring


i.

Coat a new O-ring and a new D-ring with Toyota Genuine CVT fluid FE and install them to the forward clutch piston.

NOTICE:

Ensure that the O-ring and D-ring are not twisted.



ii.

Install the forward clutch piston to the forward clutch drum sub-assembly.



Hide 35603E 21.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C446511


Hide 22.INSTALL NO. 1 CLUTCH BALANCER

a.
C446666N01
1.833,2.5 2.167,2.5 false 0.594,0.156 0.875,0.51 0.281,0.354 18 false i 4.688,0.073 4.969,0.427 0.281,0.354 18 false ii 0.594,2.021 0.875,2.375 0.281,0.354 18 false iii 4.146,2.01 4.427,2.365 0.281,0.354 18 false iv 2.208,2.417 2.667,2.615 0.458,0.198 10 false SST

i.

Coat a new D-ring with Toyota Genuine CVT fluid FE and install it to the No. 1 clutch balancer.

NOTICE:

Ensure that the D-ring is not twisted.



ii.

Install the No. 1 clutch balancer to the forward clutch drum sub-assembly.


iii.

Place SST on the No. 1 clutch balancer and compress the forward clutch return spring sub-assembly with a press.

SST
09387-00020  

NOTICE:

Do not compress the forward clutch return spring sub-assembly excessively.



iv.

Using a snap ring expander, install the snap ring to the forward clutch drum sub-assembly.



Hide 35633H 23.INSTALL FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

a.
C446667C01
2.823,1.083 3.073,1.083 3.073,1.083 3.073,2.417 false 1.583,0.5 1.917,0.5 false 2.823,1.583 3.073,1.583 false 2.833,2.083 3.083,2.083 false 1.719,1.333 1.896,1.333 false 1.5,0.833 1.885,0.833 false 1.729,0.833 1.729,1.833 1.729,1.833 1.896,1.833 false 0.49,0.167 0.771,0.521 0.281,0.354 18 false i 3.906,0.49 4.188,0.844 0.281,0.354 18 false ii 3,2.479 3.313,2.677 0.313,0.198 10 false *3 1.323,0.74 1.635,0.938 0.313,0.198 10 false *2 1.396,0.385 1.708,0.583 0.313,0.198 10 false *1
*1 Forward Clutch Flange *2 Forward Multiple Disc Clutch Clutch Disc
*3 Forward Multiple Disc Clutch Clutch Plate - -


i.

Install the forward clutch flange, 3 forward multiple disc clutch clutch discs and 3 forward multiple disc clutch clutch plates to the forward clutch drum sub-assembly.


ii.

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the forward clutch drum sub-assembly.

NOTICE:

Be careful not to damage the forward clutch drum sub-assembly.




Hide 35610A 24.INSTALL FORWARD MULTIPLE DISC CLUTCH ASSEMBLY

a.
C446668N01
0.656,0.052 0.938,0.406 0.281,0.354 18 false i 3.948,0.094 4.229,0.448 0.281,0.354 18 false ii

i.

Install the thrust bearing race to the forward multiple disc clutch assembly.


ii.

Install the forward multiple disc clutch assembly to the planetary gear assembly.



Hide 25.INSTALL STAY

a.
C446669C01
2.135,1.583 2.302,1.271 false 0.375,0.052 0.885,0.354 0.51,0.302 18 false i, ii 4.375,0.083 4.885,0.385 0.51,0.302 18 false iii 2.042,1.583 2.354,1.74 0.313,0.156 10 false *a
*a Adhesive - -


i.

Clean and degrease the bolt and installation hole in the No. 1 gear shift fork assembly.


ii.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.



iii.

Install the stay to the No. 1 gear shift fork assembly with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)



Hide 33210A 26.INSTALL NO. 1 GEAR SHIFT FORK ASSEMBLY

a.
C446670N01
1.969,0.104 2.25,0.458 0.281,0.354 18 false i 0.781,1.979 1.063,2.333 0.281,0.354 18 false ii

i.

Install the No. 1 gear shift fork assembly to the 1st gear sub-assembly.


ii.

Move the No. 1 gear shift fork assembly as shown in the illustration.



Hide 33032 27.INSTALL 1ST GEAR SUB-ASSEMBLY

a.
C446671C01
5.417,1.688 5.531,1.385 false 5.333,1.719 5.646,1.875 0.313,0.156 10 false *a 3.885,0.094 4.208,0.406 0.323,0.313 18 false iii 0.073,0.063 0.396,0.375 0.323,0.313 18 false i, ii 1.927,1.979 2.25,2.292 0.323,0.313 18 false iv
*a Adhesive - -


i.

Clean and degrease the bolt and installation hole in the No. 1 gear shift fork shaft.


ii.

Install the 1st gear sub-assembly with the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft.


iii.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.



iv.

Install the bolt to connect the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)



Hide 28.INSTALL CLUTCH DRUM OIL SEAL RING

Z101186

NOTICE:

Do not expand the gap of the clutch drum oil seal ring excessively.



a.
C446513N02
1.885,0.063 2.167,0.417 0.281,0.354 18 false i

i.

Install 2 new clutch drum oil seal rings to the stator (CVT) shaft assembly.



Hide 35370E 29.INSTALL STATOR (CVT) SHAFT ASSEMBLY

a.
C446672N02
0.448,0.104 0.729,0.458 0.281,0.354 18 false i 2.573,0.052 2.719,0.229 0.146,0.177 10 true A 2.406,0.479 2.552,0.656 0.146,0.177 10 true B 2.458,0.792 2.604,0.969 0.146,0.177 10 true A 2.542,1.198 2.688,1.375 0.146,0.177 10 true A 4.417,0.146 4.563,0.323 0.146,0.177 10 true A 4.604,0.583 4.75,0.76 0.146,0.177 10 true A 4.667,0.979 4.813,1.156 0.146,0.177 10 true B

i.

Install the stator (CVT) shaft assembly to the transaxle case sub-assembly with the 7 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
30 mm (1.18 in.) 40 mm (1.57 in.)




Hide 35165B 30.INSTALL NO. 1 TRANSMISSION CASE PLATE

a.
C446503

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35330J 31.INSTALL OIL STRAINER ASSEMBLY

a.
C446673N01
0.385,0.052 0.667,0.406 0.281,0.354 18 false i 4,0.083 4.281,0.438 0.281,0.354 18 false ii

i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the oil strainer assembly to the front oil pump assembly with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 35310A 32.INSTALL FRONT OIL PUMP ASSEMBLY

a.
C446674N01
0.375,0.063 0.656,0.417 0.281,0.354 18 false i 3.938,0.063 4.219,0.417 0.281,0.354 18 false ii 5.042,0.063 5.198,0.26 0.156,0.198 10 true A 6.49,0.583 6.646,0.781 0.156,0.198 10 true B 6.24,1.281 6.396,1.479 0.156,0.198 10 true A 5.271,1.479 5.427,1.677 0.156,0.198 10 true B

i.

Coat a new front oil pump cover gasket with Toyota Genuine CVT fluid FE and install it to the transaxle case sub-assembly.


ii.

Install the front oil pump assembly to the transaxle case sub-assembly with the 4 bolts.

Torque:
22.1 N*m (225 kgf*cm, 16 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
30 mm (1.18 in.) 40 mm (1.57 in.)




Hide 35316A 33.INSTALL NO. 1 TRANSMISSION OIL PUMP SEPARATE PLATE

a.
C446500

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35783N 34.INSTALL DRIVEN SPROCKET

a.
C446499N03
0.396,0.063 0.677,0.417 0.281,0.354 18 false ii 3.833,0.063 4.115,0.417 0.281,0.354 18 false i

i.

Install the snap ring to the front oil pump assembly.


ii.

Using a snap ring expander, install the driven sprocket to the front oil pump assembly.



Hide 35782P 35.INSTALL DRIVE SPROCKET

a.
C446675C01
1.448,0.24 1.948,0.24 true 2.198,0.479 2.698,0.479 false 1.26,0.146 1.573,0.302 0.313,0.156 10 false *1 2.75,0.406 3.063,0.563 0.313,0.156 10 false *2 0.896,0.042 1.177,0.396 0.281,0.354 18 false i 3.854,0.063 4.135,0.417 0.281,0.354 18 false ii
*1 Drive Sprocket *2 Transmission Drive Chain


i.

Install the drive sprocket and transmission drive chain.


ii.

Install the thrust needle roller bearing to the drive sprocket.



Hide 35317A 36.INSTALL NO. 2 TRANSMISSION OIL PUMP SEPARATE PLATE

a.
C446497


Hide 37.INSTALL DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 35759A 38.INSTALL REDUCTION DRIVEN GEAR

Hide 39.INSTALL CVT TYPE T OIL SEAL

a.
C446676N02
2.115,0.927 2.854,1.031 true 0.458,0.104 0.979,0.427 0.521,0.323 18 false i, ii 1.781,0.844 2.24,1.042 0.458,0.198 10 false SST

i.

Coat the lip of a new transaxle housing type T oil seal with a small amount of MP grease.


ii.

Using SST and a hammer, install the transaxle housing type T oil seal to the transaxle housing.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Make sure that the transaxle housing type T oil seal is installed in the correct direction.




Hide 43410M 40.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C446677N01
2.156,0.927 2.917,1.167 true 0.417,0.083 0.698,0.438 0.281,0.354 18 false i 1.844,0.813 2.302,1.01 0.458,0.198 10 false SST

i.

Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.





Hide 35598B 41.INSTALL PARKING LOCK SLEEVE

a.
C446490


Hide 35557C 42.INSTALL PARKING LOCK PAWL

a.
C446489


Hide 35556N 43.INSTALL PARKING LOCK PAWL SHAFT

a.
C446678C01
3.115,0.542 3.323,0.375 3.323,0.375 3.49,0.375 false 2.563,0.167 2.896,0.167 false 2.385,0.063 2.698,0.219 0.313,0.156 10 false *1 3.552,0.292 3.865,0.448 0.313,0.156 10 false *2 0.427,0.094 0.583,0.385 0.156,0.292 18 false i
*1 Parking Lock Pawl Shaft *2 Torsion Spring


i.

Install the parking lock pawl shaft and torsion spring to the transaxle housing.



Hide 35593A 44.INSTALL CAM GUIDE SLEEVE

a.
C446487

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35809 45.INSTALL C-2 CLUTCH PRESSURE APPLY TUBE SUB-ASSEMBLY

a.
C446806N01
0.396,0.063 0.677,0.417 0.281,0.354 18 false i 3.74,0.042 4.021,0.396 0.281,0.354 18 false ii

i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the C-2 clutch pressure apply tube sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the C-2 clutch pressure apply tube sub-assembly to the transaxle housing.



Hide 35896A 46.INSTALL SECONDARY SHAFT LUBE APPLY TUBE

a.
C446807C01
4.083,3.052 3.708,2.75 true 5.552,2.948 5.26,3.292 true 4.104,3.063 4.417,3.219 0.313,0.156 10 false *a 5.146,3.302 5.344,3.552 0.198,0.25 10 false *b 2.479,0.24 2.76,0.594 0.281,0.354 18 false i 0.5,1.656 0.781,2.01 0.281,0.354 18 false ii 1.521,3.948 1.802,4.302 0.281,0.354 18 false iii
*a Protrusion *b Cutout


i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the secondary shaft lube apply tube.

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the secondary shaft lube apply tube to the transaxle housing.

NOTICE:

Align the cutout of the transaxle housing with the protrusion of the secondary shaft lube apply tube.



iii.

Using a snap ring plier, install the snap ring to the transaxle housing.



Hide 35882E 47.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C446484

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35394D 48.INSTALL OIL CLEANER(CVT) MAGNET

a.
C446483


Hide 35174B 49.INSTALL OIL RESERVOIR LOCK PLATE

a.
C446482

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35111C 50.INSTALL TRANSAXLE HOUSING

a.
C446808C02
4.135,0.26 5.031,0.573 0.896,0.313 18 false iii 4.208,2.104 4.49,2.427 0.281,0.323 18 false iv 0.302,3.031 0.583,3.354 0.281,0.323 18 false v 0.479,0.271 1.375,0.583 0.896,0.313 18 false i, ii
V100145

Area to be Cleaned
V100155

Seal Packing Start and End Point Range


i.

Clean and degrease the contact surfaces of the transaxle housing and transaxle case sub-assembly.

NOTICE:

Make sure that there is no Toyota Genuine CVT fluid FE on the contact surfaces.



ii.

Clean and degrease the 20 bolts and installation holes of the transaxle case sub-assembly.


iii.

Coat 5 new O-rings with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.

NOTICE:

Ensure that the O-rings is not twisted.



iv.

Apply seal packing to the transaxle case sub-assembly.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Standard Seal Diameter:

1.5 mm (0.0591 in.)


NOTICE:
·

Make sure to overlap the start and end points of the seal packing.

·

Make sure that the start and end points of the seal packing are within the shaded area shown in the illustration.

·

Apply seal packing in a continuous line (width 1.5 mm (0.0591 in.)) along the sealing surface.

·

After applying seal packing, install the transaxle housing to the transaxle case sub-assembly within 3 minutes and tighten the bolts within 10 minutes.




v.

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)



Hide 89413S 51.INSTALL TRANSMISSION REVOLUTION SENSOR (NC1)

a.
C446480

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 82125M 52.INSTALL TRANSMISSION WIRE

a.
C446809N01
0.51,0.135 0.792,0.49 0.281,0.354 18 false i 4.417,0.125 4.698,0.479 0.281,0.354 18 false ii 0.156,1.75 0.438,2.104 0.281,0.354 18 false iii 3.833,1.823 4.115,2.177 0.281,0.354 18 false iv

i.

Coat the O-ring of the transmission wire with Toyota Genuine CVT fluid FE.

NOTICE:

If reusing the transmission wire, check that the O-ring is not damaged.



ii.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the temperature sensor.

NOTICE:

Ensure that the O-ring is not twisted.



iii.

Install the transmission wire to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


iv.

Connect the transmission revolution sensor (NC1) connector.

NOTICE:
C467180

Securely align the wire harness with the cutout of the transaxle case sub-assembly.




Hide 35410J 53.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C467182N01
0.458,0.073 3.208,0.427 2.75,0.354 18 false i, ii, iii

i.

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


ii.

Turn the transmission control shaft lever clockwise until it stops.


iii.

Remove the transmission control shaft lever from the manual valve lever shaft.



b.
C446810C01
6.167,2.781 5.938,2.938 false 6.51,3.406 6.385,3.573 false 0.385,0.094 0.667,0.448 0.281,0.354 18 false i 3.917,0.104 4.198,0.458 0.281,0.354 18 false ii 0.729,2.094 1.01,2.448 0.281,0.354 18 false iii 6.24,2.677 6.552,2.875 0.313,0.198 10 false *1 6.25,3.573 6.563,3.771 0.313,0.198 10 false *2
*1 Manual Valve *2 Manual Valve Link Lever Sub-assembly


i.

Coat 3 new transaxle case gaskets with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.


ii.

Coat a new front oil pump cover gasket with Toyota Genuine CVT fluid FE and install it to the transaxle case sub-assembly.


iii.

Align the slit portion of the manual valve and the manual valve link lever sub-assembly as shown in the illustration, and temporarily install the transmission valve body assembly to the transaxle case sub-assembly with the 2 bolts.

Bolt Length:

40 mm (1.57 in.)




c.
C446811N01
0.365,0.052 0.646,0.406 0.281,0.354 18 false i 3.854,0.052 4.135,0.406 0.281,0.354 18 false ii 1.26,1.552 1.417,1.75 0.156,0.198 10 true A 1.563,1.552 1.719,1.75 0.156,0.198 10 true A 2.083,1.542 2.24,1.74 0.156,0.198 10 true A 1.188,0.979 1.344,1.177 0.156,0.198 10 true B 0.667,0.667 0.823,0.865 0.156,0.198 10 false B 0.969,0.052 1.125,0.25 0.156,0.198 10 true B 1.677,0.052 1.833,0.25 0.156,0.198 10 true B 2.26,0.052 2.417,0.25 0.156,0.198 10 true A 3.01,1.063 3.167,1.26 0.156,0.198 10 true B

i.

Temporarily install the 9 bolts.

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 55 mm (2.17 in.)



ii.

Connect the temperature sensor to the transmission valve body assembly.

NOTICE:

To prevent it from being pinched between the transmission valve body assembly and the transaxle side cover sub-assembly, do not let the transmission wire ride up over the area shown in the illustration.

C432793C01
0,0 0,0 false
V100145

Do not let transmission wire protrude into this area. - -





d.
C446812N01
0.365,0.115 0.646,0.469 0.281,0.354 18 false i 4.063,0.115 4.344,0.469 0.281,0.354 18 false ii 1.917,2.01 2.573,2.323 0.656,0.313 18 false iii, iv

i.

Temporarily install the temperature sensor clamp to the transmission valve body assembly with the bolt.

Bolt Length:

55 mm (2.17 in.)



ii.

Fully tighten the 12 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


iii.

Connect the 6 solenoid valve connectors.


iv.

Engage the clamp to connect the transmission wire to the solenoid lock plate.



Hide 35015Y 54.INSTALL TRANSAXLE SIDE COVER SUB-ASSEMBLY

a.
C446813C01
0.365,0.063 0.646,0.417 0.281,0.354 18 false i 3.875,0.052 4.156,0.406 0.281,0.354 18 false ii 1.667,1.938 2.323,2.292 0.656,0.354 18 false iii, iv 2.521,2.073 2.677,2.271 0.156,0.198 10 false 8 2.417,2.781 2.573,2.979 0.156,0.198 10 false 7 2.531,3.531 2.688,3.729 0.156,0.198 10 false 1 3.188,3.573 3.344,3.771 0.156,0.198 10 false 6 3.635,3.573 3.792,3.771 0.156,0.198 10 false 5 4.333,3.542 4.49,3.74 0.156,0.198 10 false 4 4.51,2.844 4.667,3.042 0.156,0.198 10 false 3 4.49,2.302 4.646,2.5 0.156,0.198 10 false 2 4.021,2.208 4.219,2.406 0.198,0.198 10 true 11 3.813,1.979 4.01,2.177 0.198,0.198 10 true 10 3.375,1.979 3.573,2.177 0.198,0.198 10 true 9
V100145

Area to be cleaned - -


i.

Clean the transaxle side cover sub-assembly installation surface of the transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surface of the transaxle case sub-assembly.



ii.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transaxle side cover sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



iii.

Temporarily install a new transaxle side cover sub-assembly to the transaxle case sub-assembly with the 11 bolts.


iv.

Fully tighten the 11 bolts in the order shown in the illustration.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)



Hide 35125E 55.INSTALL OVERFLOW (CVT) TUBE

a.
C446474N02
2.198,0.01 2.479,0.365 0.281,0.354 18 false i

i.

Using a 6 mm hexagon socket wrench, install the overflow (CVT) tube to the transaxle case sub-assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)



Hide 35125G 56.INSTALL OVERFLOW PLUG

a.
C446473N02
2.052,0.021 2.802,0.396 0.75,0.375 18 false i, ii

i.

Coat a new gasket with Toyota Genuine CVT fluid FE and install it to the overflow plug.


ii.

Using a 10 mm hexagon socket wrench, install the overflow plug to the transaxle case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)



Hide 57.INSTALL REFILL PLUG

a.
C446814N01
0.438,0.115 0.875,0.448 0.438,0.333 18 false i, ii

i.

Coat a new gasket with Toyota Genuine CVT fluid FE and install it to the refill plug.


ii.

Install the refill plug to the rear transaxle case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)



Hide 89637K 58.INSTALL OIL PRESSURE SENSOR

a.
C446815N01
0.833,0.042 1.115,0.396 0.281,0.354 18 false i 3.792,0.042 4.073,0.396 0.281,0.354 18 false ii

i.

Coat the O-ring of the oil pressure sensor with Toyota Genuine CVT fluid FE.

NOTICE:

If reusing the oil pressure sensor, check that the O-ring is not damaged.



ii.

Using a 27 mm deep socket wrench, install the oil pressure sensor to the rear transaxle case sub-assembly.

Torque:
20.6 N*m (210 kgf*cm, 15 ft.*lbf)

NOTICE:

Be careful not to damage the O-ring.




Hide 89413T 59.INSTALL TRANSMISSION REVOLUTION SENSOR (NSS)

a.
C446816N01
0.385,0.063 0.667,0.417 0.281,0.354 18 false i 3.781,0.063 4.063,0.417 0.281,0.354 18 false ii

i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NSS).

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the transmission revolution sensor (NSS) to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.




Hide 89413N 60.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)

a.
C446817N01
0.417,0.052 0.698,0.406 0.281,0.354 18 false i 3.854,0.042 4.135,0.396 0.281,0.354 18 false ii

i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NT).

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the transmission revolution sensor (NT) to the rear transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.




Hide 35151K 61.INSTALL AUTOMATIC TRANSMISSION CASE COVER

a.
C446470


Hide 89413M 62.INSTALL TRANSMISSION REVOLUTION SENSOR (NOUT)

a.
C446818N01
0.365,0.042 0.646,0.396 0.281,0.354 18 false i 3.844,0.042 4.125,0.396 0.281,0.354 18 false ii

i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NOUT).

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the transmission revolution sensor (NOUT) to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.




Hide 89419B 63.INSTALL SHIFT STROKE SENSOR

a.
C446819N01
0.385,0.042 0.667,0.396 0.281,0.354 18 false i 3.771,0.031 4.052,0.385 0.281,0.354 18 false ii

i.

Coat the O-ring of the shift stroke sensor with Toyota Genuine CVT fluid FE.

NOTICE:

If reusing the shift stroke sensor, check that the O-ring is not damaged.



ii.

Install the shift stroke sensor to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.




Hide 84540 64.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C446820C01
6.167,2.438 6.385,2.417 6.385,2.417 6.177,2.594 true 0.75,3.417 0.948,3.604 0.198,0.188 10 true *a 6.427,2.333 6.74,2.49 0.313,0.156 10 false *b 0.083,0.042 0.365,0.396 0.281,0.354 18 false i 3.667,0.094 4.271,0.406 0.604,0.313 18 false ii, iv 0.083,1.927 0.688,2.24 0.604,0.313 18 false iii 3.875,2.135 4.479,2.448 0.604,0.313 18 false v 0.094,3.927 0.698,4.24 0.604,0.313 18 false vi 3.896,4.052 4.5,4.365 0.604,0.313 18 false vii
*a N *b Protrusion


i.

Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.


ii.

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


iii.

Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



iv.

Remove the transmission control shaft lever from the manual valve lever shaft.


v.

Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


vi.

Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


vii.

Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:

Be careful of the direction of the transmission control shaft lever.




Hide 33493C 65.INSTALL TRANSMISSION OIL COOLER ASSEMBLY

a.
C446821N01
0.385,0.052 0.667,0.406 0.281,0.354 18 false i 4.031,0.083 4.313,0.438 0.281,0.354 18 false ii

i.

Coat 2 new O-rings with Toyota Genuine CVT fluid FE and install them to the transaxle housing.

NOTICE:

Ensure that the O-rings are not twisted.



ii.

Install the transmission oil cooler to the transaxle housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)