Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0438353 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B590417N01
0.677,2.781 1.677,2.948 1,0.167 5.417,1.458 5.75,1.458 false 3.417,2.948 3.75,2.948 false 1.677,2.865 2.01,2.865 false 6.01,1.344 6.292,1.698 0.281,0.354 18 false 1 4.333,0.625 4.646,0.823 0.313,0.198 10 false x2 2.104,2.823 2.417,3.021 0.313,0.198 10 false x2 3.792,2.854 4.104,3.052 0.313,0.198 10 false *1 0.729,2.792 3.177,2.948 2.448,0.156 8 false 7.5 (76, 66 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 WINDSHIELD WIPER MOTOR ASSEMBLY 85110 (Click here) - -

*1 WINDSHIELD WIPER LINK ASSEMBLY - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

MP grease

B586306N02
1,0.427 1.74,0.583 0.74,0.156 1.729,1.885 2.479,2.052 0.75,0.167 1.479,4.458 2.49,4.625 1.01,0.167 3.115,0.969 3.292,0.479 3.292,0.479 3.458,0.479 false 2.49,1.646 2.771,1.646 false 1.74,0.51 2.073,0.51 false 0.573,2.063 0.906,2.063 false 2.479,1.958 2.813,1.958 false 2.49,4.542 2.823,4.542 false 1.927,5.021 2.198,5.021 false 6.156,4.677 6.25,4.406 6.25,4.406 6.417,4.406 false 4.604,2.677 4.906,1.958 4.906,1.958 5.073,1.958 false 1.458,3.333 1.844,3.333 false 6.469,0.271 6.802,0.271 false 1.677,0.229 2.01,0.229 false 2.969,4.51 3.281,4.708 0.313,0.198 10 false x2 4.323,3.552 4.635,3.75 0.313,0.198 10 false x2 3.792,0.344 4.073,0.698 0.281,0.354 18 false 7 5.375,1.823 5.656,2.177 0.281,0.354 18 false 6 6.49,4.25 6.771,4.604 0.281,0.354 18 false 4 1.708,4.844 1.99,5.198 0.281,0.354 18 false 2 1.229,3.208 1.51,3.563 0.281,0.354 18 false 3 0.354,1.885 0.635,2.24 0.281,0.354 18 false 5 2.271,1.49 2.688,1.823 0.417,0.333 18 false 9 1.5,0.063 1.917,0.396 0.417,0.333 18 false 9 1.083,0.438 1.927,0.646 0.844,0.208 8 false 26 (265, 19) 1.813,1.906 2.698,2.177 0.885,0.271 8 false 26 (265, 19) 1.542,4.479 2.792,4.656 1.25,0.177 8 false 5.5 (56, 49 in.*lbf) 6.25,0.104 6.667,0.438 0.417,0.333 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

2 WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY - (Click here) - -
3 COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY 55708 (Click here) - -
4 FRONT FENDER TO COWL SIDE SEAL LH 53867 - - -
5 FRONT FENDER TO COWL SIDE SEAL RH 53866 - - -
6 FRONT WIPER ARM AND BLADE ASSEMBLY LH - (Click here) - -
7 FRONT WIPER ARM AND BLADE ASSEMBLY RH - (Click here) - -
8 FRONT WIPER ARM AND BLADE ASSEMBLY - (Click here) - -
9 FRONT WIPER ARM HEAD CAP 85292B - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
B586307C01
5.448,0.771 5.865,0.344 true 4.969,0.625 5.344,0.26 true 1.563,0.271 2.104,0.344 true 5.927,0.229 6.24,0.427 0.313,0.198 10 false *a 5.417,0.146 5.729,0.344 0.313,0.198 10 false *1 1.375,0.167 1.688,0.365 0.313,0.198 10 false *a 1.188,1.271 1.521,1.542 0.333,0.271 18 false ii 2.635,1.125 2.969,1.396 0.333,0.271 18 false ii 2.927,0.021 3.26,0.292 0.333,0.271 18 false iii 3.635,0.052 3.969,0.323 0.333,0.271 18 false iv 0.406,0 0.563,0.281 0.156,0.281 18 false i
*1 No. 1 Windshield Wiper Link Rod - -
*a Pivot of Windshield Wiper Motor Assembly - -
V100136

MP grease - -


i.

Engage the guides to install the windshield wiper motor assembly.


ii.

Using a T30 "TORX" socket wrench, install the 2 screws.

Torque:
7.5 N*m (76 kgf*cm, 6 ft.*lbf)


iii.

Apply MP grease to the pivot of the windshield wiper motor assembly.


iv.

Connect the No. 1 windshield wiper link rod to the pivot of the windshield wiper motor assembly.



Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Z101186

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.



Torque:
5.5 N*m (56 kgf*cm, 4 ft.*lbf)

Hide 55708 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Z101186

NOTICE:

When installing the cowl top ventilator louver sub-assembly, it may contact the brake master cylinder reservoir filler cap assembly and cause it to fall off. Check the installation condition of the brake master cylinder reservoir filler cap assembly after installing the cowl top ventilator louver sub-assembly.



Hide 53867 4.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866 5.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
B586311C02
2.292,1.302 2.656,0.99 true 2.323,2.281 2.76,2.219 true 5.26,2.323 5.573,2.573 true 2.698,0.865 3.01,1.063 0.313,0.198 10 false *a 2.802,2.125 3.115,2.323 0.313,0.198 10 false *a 0.51,0.146 1.073,0.531 0.563,0.385 18 false i, ii 3.979,0.167 4.615,0.531 0.635,0.365 18 false iii, iv 1.771,3.875 2.052,4.25 0.281,0.375 18 false v 5.021,2.24 5.219,2.396 0.198,0.156 10 true *b 5.698,2.281 5.813,2.469 0.115,0.188 10 true A 5.781,2.563 5.917,2.708 0.135,0.146 10 true A
*a Serration *b Alignment Mark


i.

When reusing the front wiper arm and blade assembly LH:

1. Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.



ii.

When reusing the windshield wiper motor and link assembly:

1. Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper pivot serrations.



iii.

Set the automatic stop position by the below procedure.

1. Turn the ignition switch on.

2. Operate the windshield wiper motor assembly and stop the windshield wiper motor and link assembly at the automatic stop position.

3. Turn the ignition switch off.


iv.

Install the front wiper arm and blade assembly LH to the position shown in the illustration.

Reference Measurement:
Area Measurement
A 10 mm (0.394 in.)



v.

Hold the wiper arm by hand to install the nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)



Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
B586310C02
2.135,1.115 2.552,0.729 true 2.188,1.938 2.667,1.958 true 5.552,2.625 5.385,2.313 true 2.594,0.635 2.906,0.833 0.313,0.198 10 false *a 2.729,1.865 3.042,2.063 0.313,0.198 10 false *a 5.729,2.427 5.854,2.594 0.125,0.167 10 true A 5.74,2.698 5.854,2.854 0.115,0.156 10 true A 5.177,2.219 5.354,2.396 0.177,0.177 10 true *b 0.5,0.125 1.073,0.469 0.573,0.344 18 false i, ii 3.979,0.135 4.646,0.458 0.667,0.323 18 false iii 1.792,3.854 2.104,4.177 0.313,0.323 18 false iv
*a Serration *b Alignment Mark


i.

When reusing the front wiper arm and blade assembly RH:

1. Clean the front wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.



ii.

When reusing the windshield wiper motor and link assembly:

1. Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper pivot serrations.



iii.

Install the front wiper arm and blade assembly RH to the position as shown in the illustration.

Reference Measurement:
Area Measurement
A 10 mm (0.394 in.)



iv.

Hold the wiper arm by hand to install the nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)



Hide 8.INSPECT FRONT WIPER ARM AND BLADE ASSEMBLY

Hide 85292B 9.INSTALL FRONT WIPER ARM HEAD CAP