Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3700E _58 Vehicle Interior _093087 METER / GAUGE / DISPLAY _0438738 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150013  Fuel Sender Circuit Open  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B150013 Fuel Sender Circuit Open Diagnosis Condition:
·

The ignition switch is ON

·

IG power source voltage is 9.5 V or more


Malfunction Status:
·

Voltage signal from fuel sender gauge assembly is 0.2 V or less

·

Voltage signal from fuel sender gauge assembly is 4.7 V or more


Malfunction Time:

10 seconds or more


·

Wire harness or connector

·

Fuel sender gauge assembly

·

Fuel suction tube with pump and gauge assembly

·

Combination meter assembly


Combination Meter A

WIRING DIAGRAM

E436630E02
5.031,3.052 6.865,3.406 1.833,0.354 10 false Combination Meter Assembly 0.115,2.844 3.302,3.25 3.188,0.406 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.354,2.021 2.323,2.469 1.969,0.448 10 false Fuel Sender Gauge Assembly 0.365,1.844 1.292,2.052 0.927,0.208 10 false A 0.115,2.656 1.042,2.865 0.927,0.208 10 false O22 2.052,1.5 2.979,1.708 0.927,0.208 10 false FE 2.042,0.656 2.969,0.865 0.927,0.208 10 false FS 2.042,1.073 2.969,1.281 0.927,0.208 10 false FV 5,1.073 5.927,1.281 0.927,0.208 10 false FV 4.979,1.479 5.906,1.688 0.927,0.208 10 false FE&B 4.99,0.656 5.917,0.865 0.927,0.208 10 false FR 6.229,0.458 6.656,0.813 0.427,0.354 10 false 5 V 2.333,1.073 3.26,1.281 0.927,0.208 10 false 1 2.344,0.667 3.271,0.875 0.927,0.208 10 false 3 2.344,1.49 3.271,1.698 0.927,0.208 10 false 2 1.583,1.5 2.51,1.708 0.927,0.208 10 false 2 0.938,0.917 1.865,1.125 0.927,0.208 10 false 1 1.583,1.073 2.51,1.281 0.927,0.208 10 false 3 4.719,1.073 5.115,1.396 0.396,0.323 10 false 14 4.74,0.646 5.135,0.969 0.396,0.323 10 false 31 4.719,1.479 5.115,1.802 0.396,0.323 10 false 24 5.042,2.885 6.396,3.323 1.354,0.438 10 false H6

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0.00 L, Max.: 655.35 L or Unset Fuel sender input value -
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 409 20

Result:
Result Proceed to
Fuel level data can be displayed on the GTS. A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

Pre-procedure1

a.

Disconnect the O22 fuel suction tube with pump and gauge assembly connector.


b.

Disconnect the H6 combination meter assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O22,H6)Location & Routing

Click Connector(O22)Body>Floor Wire>Fuel Suction Tube with Pump & Gage Assembly

Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

O22-1 (FV) - H6-14 (FV) Always Below 1 Ω
O22-3 (FS) - H6-31 (FR) Always Below 1 Ω
O22-2 (FE) - H6-24 (FE&B) Always Below 1 Ω
O22-1 (FV) or H6-14 (FV) - Body ground Always 10 kΩ or higher
O22-3 (FS) or H6-31 (FR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for M15A-FKS A
for M15A-FXE B



A

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

5.INSPECT FUEL SENDER GAUGE ASSEMBLY
4.INSPECT FUEL SENDER GAUGE ASSEMBLY

OK

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

OK

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.

Measure the resistance according to the value(s) in the table below.

E437279C05
1.667,0.333 2.083,0.583 0.417,0.25 5,0.333 5.417,0.583 0.417,0.25 1.042,1.521 1.542,1.521 true 2.219,1.521 2.719,1.521 true 1.24,0.948 1.813,1.417 true 1.75,0.406 2.208,0.604 0.458,0.198 10 false O22 5.177,0.385 5.333,0.583 0.156,0.198 10 false A 0.854,1.458 1.167,1.656 0.313,0.198 10 false FS 1.01,0.865 1.323,1.063 0.313,0.198 10 false FE 2.76,1.448 3.073,1.646 0.313,0.198 10 false FV 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O22)Location & Routing

Click Connector(O22)Body>Floor Wire>Fuel Suction Tube with Pump & Gage Assembly

O22-1 (FV) - A-3 Always Below 1 Ω
O22-2 (FE) - A-2 Always Below 1 Ω
O22-3 (FS) - A-1 Always Below 1 Ω
O22-1 (FV) - O22-3 (FS) or A-3 - A-1 Always 10 kΩ or higher
O22-1 (FV) - O22-2 (FE) or A-3 - A-2 Always 10 kΩ or higher
O22-2 (FE) - O22-3 (FS) or A-2 - A-1 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY