Home › Vehicle Interior › METER / GAUGE / DISPLAY › COMBINATION METER › 2020.08–2021.07
RM3700E _58 Vehicle Interior _093087 METER / GAUGE / DISPLAY _0438736 COMBINATION METER A

METER / GAUGE / DISPLAY  COMBINATION METER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B596188N02
0.375,0.271 0.729,0.271 false 0.427,0.729 0.781,0.729 false 1.583,1.396 1.583,1.719 false 3.104,1.031 3.104,1.354 false 4.625,0.5 4.979,0.5 false 5.844,1.885 6.281,1.885 false 1.24,3.083 1.594,3.083 false 4.198,2.802 3.885,2.802 false 5.344,3.885 5.698,3.885 false 6.156,4.969 6.375,4.729 6.375,4.729 6.542,4.729 false 3.729,1.719 4.125,1.719 false 3.01,3.865 2.646,3.865 false 0.813,0.125 1.094,0.479 0.281,0.354 18 false 1 0.844,0.573 1.125,0.927 0.281,0.354 18 false 2 1.521,1.719 1.802,2.073 0.281,0.354 18 false 6 3.031,1.385 3.313,1.74 0.281,0.354 18 false 4 5.031,0.344 5.313,0.698 0.281,0.354 18 false 5 4.417,1.604 4.74,1.927 0.323,0.323 18 false 7 6.583,1.76 7.042,2.094 0.458,0.333 18 false 12 1.646,2.938 2.01,3.313 0.365,0.375 18 false 3 4.26,2.635 4.823,3.135 0.563,0.5 18 false 9 5.74,3.729 6.198,4.052 0.458,0.323 18 false 11 6.583,4.563 7.042,4.906 0.458,0.344 18 false 10 3.333,3.719 3.76,4.073 0.427,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 NO. 2 INSTRUMENT SIDE PANEL 55318F - - -
4 CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH 55475B - - -
5 INSTRUMENT PANEL FINISH PANEL 55431A - - -
6 LOWER INSTRUMENT PANEL FINISH PANEL 55432B - - -
7 SWITCH HOLE BASE SUB-ASSEMBLY 55407B (Click here) - -
8 SHIFT LEVER CAP 33554 (Click here) - -
9 CONSOLE BOX ASSEMBLY 58810J - - -
10 FRONT DOOR SCUFF PLATE RH 67913B - - -
11 COWL SIDE TRIM BOARD RH 62111C - - -
12 NO. 1 INSTRUMENT SIDE PANEL 55317E - - -

B594090N01
4.906,2.219 5.292,2.219 false 1.281,3.26 1.615,3.26 false 5.729,3.083 5.396,3.083 false 3.854,0.25 4.021,0.25 4.021,0.25 4.208,0.552 false 2.375,0.406 2.542,0.406 2.542,0.406 2.719,0.844 false 0.938,3.094 1.49,3.448 0.552,0.354 18 false 13 5.781,2.948 6.333,3.302 0.552,0.354 18 false 14 5.719,2.073 6.083,2.375 0.365,0.302 18 false 15 2.042,0.24 2.594,0.594 0.552,0.354 18 false 17 3.51,0.104 4.063,0.458 0.552,0.354 18 false 16 4.51,1.323 4.823,1.521 0.313,0.198 10 false x2 2.802,1.417 3.115,1.615 0.313,0.198 10 false x2 3.302,3.469 3.615,3.667 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

13 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
14 HOOD LOCK CONTROL LEVER SUB-ASSEMBLY 53601 - - -
15 LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY 55480D (Click here)
16 INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY 55410C - - -
17 COMBINATION METER ASSEMBLY 83100 - - -

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55318F 3.REMOVE NO. 2 INSTRUMENT SIDE PANEL

a.

Use the same procdure as for the NO. 1 side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55475B 4.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55431A 5.REMOVE INSTRUMENT PANEL FINISH PANEL

Hide 55432B 6.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55407B 7.REMOVE SWITCH HOLE BASE SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 33554 8.REMOVE SHIFT LEVER CAP

Z101186

Click here(Click here)

Hide 58810J 9.REMOVE CONSOLE BOX ASSEMBLY

Hide 67913B 10.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62111C 11.REMOVE COWL SIDE TRIM BOARD RH

Hide 55317E 12.REMOVE NO. 1 INSTRUMENT SIDE PANEL

Z101186

Click here(Click here)

Hide 55606 13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 53601 14.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55480D 15.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Z101186

Click here(Click here)

Hide 55410C 16.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 83100 17.REMOVE COMBINATION METER ASSEMBLY

a.
E435947