Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440166 NAME PLATE A

EXTERIOR PANELS / TRIM  NAME PLATE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B591204N02
0.094,0.229 7.073,4.74 6.979,4.51 1.979,4.104 1.979,3.771 false 5.271,4.083 5.271,3.792 false 3.625,4.729 3.583,0.24 false 0.042,0.031 0.417,0.271 0.375,0.24 12 false *A 0.292,0.24 0.667,0.479 0.375,0.24 12 false *B 3.781,0.24 4.156,0.479 0.375,0.24 12 false *C 2.167,4.083 2.448,4.438 0.281,0.354 18 false 1 5.406,4.094 5.688,4.448 0.281,0.354 18 false 1 5.25,4.125 5.625,4.365 0.375,0.24 10 false ● 2,4.125 2.375,4.365 0.375,0.24 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 SIDE PANEL EMBLEM 75374 (Click here) - -

*A for HV Model *B for LH Side
*C for RH Side - -
● Non-reusable part - -

B591215N02
3.865,3.01 5.958,4.396 2.094,1.385 1.688,1.333 1.854,1.333 1.854,1.333 2.792,1.646 true 4.427,1.635 5.094,1.281 5.094,1.281 5.26,1.281 true 2.583,3.938 2.583,3.615 false 5,3.896 5,3.573 false 1.354,1.24 1.813,1.438 0.458,0.198 10 false <A> 5.333,1.177 5.792,1.375 0.458,0.198 10 false <B> 2.323,3.979 2.781,4.177 0.458,0.198 10 false <A> ● 4.833,3.979 5.292,4.177 0.458,0.198 10 false <B> ● 3.896,3.042 4.271,3.281 0.375,0.24 12 false *A 2.781,3.927 3.052,4.24 0.271,0.313 18 false 2 5.271,3.927 5.542,4.24 0.271,0.313 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

2 NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE - (Click here) - -
3 NO. 4 BACK DOOR NAME PLATE 75444A (Click here) - -

*A for HV Model AWD - -
● Non-reusable part - -

B591212N02
4.031,4.24 6.594,5.615 2.563,1.375 2.813,3.583 2.396,3.583 false 3.594,0.885 4.802,0.198 4.802,0.198 4.969,0.198 true 4.313,1.375 4.979,0.875 4.979,0.875 5.146,0.875 true 2.688,1.365 2.104,0.865 2.104,0.865 1.938,0.865 true 1.854,5.073 2.094,4.656 2.094,4.656 2.25,4.656 false 4.792,5.083 5.031,4.656 5.031,4.656 5.177,4.656 false 5.906,4.5 6.188,4.854 0.281,0.354 18 false 5 4.094,4.292 4.469,4.531 0.375,0.24 12 false *A 5.031,0.115 5.531,0.469 0.5,0.354 10 false <A> 5.219,0.792 5.719,1.146 0.5,0.354 10 false <B> 1.615,0.781 2.115,1.135 0.5,0.354 10 false <C> 2.979,4.49 3.26,4.844 0.281,0.354 18 false 4 1.802,3.49 2.583,3.844 0.781,0.354 10 false <A> ● 2.521,4.552 3.021,4.906 0.5,0.354 10 false <C> ● 5.458,4.563 5.958,4.917 0.5,0.354 10 false <B> ● 2.24,3.427 3.021,3.781 0.781,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

4 NO. 2 BACK DOOR NAME PLATE 75442A (Click here) - -
5 NO. 1 BACK DOOR NAME PLATE 75441E (Click here) - -
6 SYMBOL EMBLEM 75741E (Click here) - -

*A for HV Model - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

Z101186

NOTICE:

When installing the new name plates, heat the vehicle body, back door outside garnish and name plates using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60 °C (104 to 140 °F)
·

Back Door Outside Garnish

·

Name Plates


20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat vehicle body, back door outside garnish and name plates or excessively.


PROCEDURE

Hide 75374 1.INSTALL SIDE PANEL EMBLEM (for HV Model)

a.

for LH Side:

B591206C01
5.271,1 4.979,0.51 true 5.198,1.854 5.021,1.573 true 5.938,1.854 6.177,1.531 true 1.229,0.75 1.51,1.104 0.281,0.354 18 false i 3.917,0.656 4.198,1.01 0.281,0.354 18 false ii 5.323,0.938 5.563,1.135 0.24,0.198 10 true *b 5.26,1.792 5.5,1.99 0.24,0.198 10 true *b 4.042,0.146 4.281,0.344 0.24,0.198 10 true *a 5.76,1.771 6,1.969 0.24,0.198 10 true *b 4.26,0.906 4.427,1.135 0.167,0.229 10 true A 4.781,1.781 4.927,2.021 0.146,0.24 10 true B 5.427,2.531 5.615,2.729 0.188,0.198 10 true C
*a Reference Values *b End of R


Standard Measurement:
Area Measurement Area Measurement
A 130.5 mm B 28.8 mm
C 160.8 mm - -


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the side panel emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new side panel emblem.

1. Using a heat light, heat the vehicle body and side panel emblem.

2. Remove the release paper from the side panel emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the side panel emblem as shown in the illustration.

HINT:

Press the side panel emblem firmly to install it.




b.

for RH Side:

B591207C01
5.865,0.771 6.083,0.5 true 5.25,1.708 5.073,1.49 true 5.917,1.719 6.104,1.521 true 1.24,0.75 1.521,1.104 0.281,0.354 18 false i 3.917,0.646 4.198,1 0.281,0.354 18 false ii 4.146,0.219 4.406,0.49 0.26,0.271 10 false *a 5.625,0.708 5.813,0.917 0.188,0.208 10 true *b 5.292,1.635 5.479,1.844 0.188,0.208 10 true *b 5.698,1.635 5.885,1.844 0.188,0.208 10 true *b 5.646,2.417 5.833,2.625 0.188,0.208 10 true A 6.188,1.719 6.313,1.938 0.125,0.219 10 true B 6.646,0.844 6.833,1.063 0.188,0.219 10 true C
*a Reference Values *b End of R


Standard Measurement:
Area Measurement Area Measurement
A 166.8 mm B 34.8 mm
C 146.2 mm - -


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the side panel emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new side panel emblem.

1. Using a heat light, heat the vehicle body and side panel emblem.

2. Remove the release paper from the side panel emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the side panel emblem as shown in the illustration.

HINT:

Press the side panel emblem firmly to install it.




Hide 2.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.
B590014C02
5.135,0.802 4.927,0.594 true 6.323,0.802 6.115,0.594 true 4.573,0.24 4.458,0.5 true 0.365,0.042 0.646,0.396 0.281,0.354 18 false i 3.24,0.063 3.521,0.417 0.281,0.354 18 false ii 3.5,0.063 3.719,0.24 0.219,0.177 10 true *a 3.74,0.573 3.885,0.771 0.146,0.198 10 true A 4.698,1.063 4.844,1.26 0.146,0.198 10 true B 5.198,1.344 5.344,1.542 0.146,0.198 10 true C 5.135,0.833 5.323,1.031 0.188,0.198 10 true *b 6.292,0.833 6.49,1.021 0.198,0.188 10 true *b 6.865,0.667 7.01,0.865 0.146,0.198 10 true D 4.583,0.125 4.771,0.323 0.188,0.198 10 true *b
*a Reference Values *b End of R


Standard Measurement:
Area Measurement Area Measurement
A 10.1 mm (0.398 in.) B 21.9 mm (0.862 in.)
C 90.6 mm (3.567 in.) D 18.1 mm (0.713 in.)


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 2 luggage compartment door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new No. 2 luggage compartment door name plate.

1. Using a heat light, heat the vehicle body and No. 2 luggage compartment door name plate.

2. Remove the release paper from the No. 2 luggage compartment door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the No. 2 luggage compartment door name plate as shown in the illustration.

HINT:

Press the No. 2 luggage compartment door name plate firmly to install it.




Hide 75444A 3.INSTALL NO. 4 BACK DOOR NAME PLATE (for HV Model AWD)

a.
B590010C02
3.896,1.042 4.125,0.875 true 5.479,1.115 5.74,0.823 true 6.135,0.323 6.344,0.51 true 3.5,0.042 3.708,0.219 0.208,0.177 10 true *a 3.656,0.958 3.885,1.125 0.229,0.167 10 true *b 0.365,0.052 0.646,0.406 0.281,0.354 18 false i 3.229,0.052 3.51,0.406 0.281,0.354 18 false ii 5.26,1.146 5.49,1.313 0.229,0.167 10 true *b 5.031,1.573 5.146,1.76 0.115,0.188 10 true B 5.875,1.125 5.99,1.313 0.115,0.188 10 true C 6.698,0.854 6.813,1.042 0.115,0.188 10 true D 5.896,0.219 6.104,0.396 0.208,0.177 10 true *b 4.542,0.958 4.688,1.125 0.146,0.167 10 true A
*a Reference Values *b End of R


Standard Measurement:
Area Measurement Area Measurement
A 22.6 mm (0.890 in.) B 115.7 mm (4.555 in.)
C 21.7 mm (0.854 in.) D 13.8 mm (0.543 in.)


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 4 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new No. 4 back door name plate.

1. Using a heat light, heat the vehicle body and No. 4 back door name plate.

2. Remove the release paper from the No. 4 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the No. 4 back door name plate as shown in the illustration.

HINT:

Press the No. 4 back door name plate firmly to install it.




Hide 75442A 4.INSTALL NO. 2 BACK DOOR NAME PLATE

a.
B590012C02
6.104,0.823 6.323,0.594 true 5.073,0.792 4.844,0.594 true 4.417,0.333 4.198,0.479 true 3.49,0.063 3.719,0.271 0.229,0.208 10 true *a 5.094,0.802 5.302,0.99 0.208,0.188 10 true *b 5.896,0.833 6.104,1.021 0.208,0.188 10 true *b 0.375,0.042 0.656,0.396 0.281,0.354 18 false i 3.229,0.063 3.51,0.417 0.281,0.354 18 false ii 3.729,0.802 3.865,1 0.135,0.198 10 true A 4.479,1.365 4.604,1.531 0.125,0.167 10 true B 5.25,1.604 5.375,1.771 0.125,0.167 10 true C 6.896,0.885 7.021,1.052 0.125,0.167 10 true D 4.448,0.229 4.656,0.417 0.208,0.188 10 true *b
*a Reference Values *b End of R


Standard Measurement:
Area Measurement Area Measurement
A 36.5 mm (1.437 in.) B 35.8 mm (1.409 in.)
C 118.5 mm (4.665 in.) D 46.2 mm (1.819 in.)


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 2 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new No. 2 back door name plate.

1. Using a heat light, heat the vehicle body and No. 2 back door name plate.

2. Remove the release paper from the No. 2 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the No. 2 back door name plate as shown in the illustration.

HINT:

Press the No. 2 back door name plate firmly to install it.




Hide 75441E 5.INSTALL NO. 1 BACK DOOR NAME PLATE (for HV Model)

a.
B591214C01
4.208,0.844 4.427,0.677 true 5.271,0.885 5.49,0.708 true 0.521,0.073 0.802,0.427 0.281,0.354 18 false i 3.385,0.073 3.667,0.427 0.281,0.354 18 false ii 3.979,0.792 4.167,1.021 0.188,0.229 10 true *b 5.021,0.802 5.208,1.031 0.188,0.229 10 true *b 4.667,0.813 4.823,1.01 0.156,0.198 10 true A 4.979,1.49 5.135,1.688 0.156,0.198 10 true B 5.521,1.208 5.646,1.375 0.125,0.167 10 true C 6.219,0.719 6.365,0.885 0.146,0.167 10 true D 3.698,0.083 3.885,0.313 0.188,0.229 10 true *a
*a Reference Values *b End of R


Standard Measurement:
Area Measurement Area Measurement
A 47.6 mm (1.874 in.) B 146 mm (5.748 in.)
C 17.7 mm (0.697 in.) D 25.1 mm (0.988 in.)


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 1 back door name plate with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new No. 1 back door name plate.

1. Using a heat light, heat the vehicle body and No. 1 back door name plate.

2. Remove the release paper from the No. 1 back door name plate.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the No. 1 back door name plate as shown in the illustration.

HINT:

Press the No. 1 back door name plate firmly to install it.




Hide 75741E 6.INSTALL SYMBOL EMBLEM

a.
B590017C03
4.948,1.313 5.219,0.948 true 6.333,1.313 6.042,1.042 true 0.365,0.052 0.646,0.406 0.281,0.354 18 false i 4.052,0.073 4.333,0.427 0.281,0.354 18 false ii 4.844,1.344 5.063,1.552 0.219,0.208 10 true *a 6.365,1.344 6.583,1.552 0.219,0.208 10 true *a
*a Location Pin - -


i.

Clean the back door outside garnish.

1. Using a heat light, heat the back door outside garnish.

2. Remove any remaining double-sided tape from the back door outside garnish.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the symbol emblem with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new symbol emblem.

1. Using a heat light, heat the back door outside garnish and symbol emblem.

2. Remove the release paper from the symbol emblem.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Engage the location pins to install the symbol emblem as shown in the illustration.

HINT:

Press the symbol emblem firmly to install it.