Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT PILLAR UPPER COVER
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440172 FRONT PILLAR UPPER COVER A

EXTERIOR PANELS / TRIM  FRONT PILLAR UPPER COVER  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B591176N02
6.25,3.396 6.25,3.063 false 5.563,2.865 5.563,3.135 5.563,3.135 5.448,3.135 false 6.188,3.385 6.469,3.74 0.281,0.354 18 false 1 5.292,3 5.573,3.354 0.281,0.354 18 false 2 5.094,3.094 5.375,3.448 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT DOOR FRONT LOWER FRAME UPPER COVER 67496C - - -
2 FRONT PILLAR UPPER COVER SUB-ASSEMBLY 60118 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 67496C 1.INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER

Hide 60118 2.INSTALL FRONT PILLAR UPPER COVER SUB-ASSEMBLY

Z101186

NOTICE:

When installing the front pillar upper cover sub-assembly, heat the vehicle body using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.
B591177C04
2.865,3.896 3.229,4.031 true 1.979,1.729 2.417,1.833 false 5.792,2.271 5.844,2.51 false 1.542,2.594 1.802,2.615 false 2.24,2.615 2.344,2.802 false 5.229,2.51 5.333,2.698 false 0.896,0.125 1.177,0.479 0.281,0.354 18 false i 3.583,0.063 3.865,0.417 0.281,0.354 18 false ii 1.979,3.083 2.26,3.438 0.281,0.354 18 false iii 2.833,3.823 3.052,4.01 0.219,0.188 10 true *a 3.906,4.094 4.125,4.385 0.219,0.292 18 true iv 4.969,0.635 5.115,0.813 0.146,0.177 10 true A 5.344,0.625 5.5,0.802 0.156,0.177 10 true A 4.823,1.125 4.969,1.302 0.146,0.177 10 true B 4.813,1.49 4.958,1.667 0.146,0.177 10 true B 1.271,1.448 1.646,1.594 0.375,0.146 10 true A-A 4.375,1.844 4.75,1.99 0.375,0.146 10 true B-B 2.469,1.75 2.615,1.927 0.146,0.177 10 true *1 5.792,2.552 5.938,2.729 0.146,0.177 10 true *1 1.354,2.521 1.5,2.698 0.146,0.177 10 true *2 2.302,2.833 2.448,3.01 0.146,0.177 10 true *3 5.292,2.719 5.438,2.896 0.146,0.177 10 true *4
*1 Front pillar upper cover sub-assembly *2 Windshield glass
*3 Windshield outside moulding *4 Front fender to cowl side seal
*a Double-sided Tape - -


i.

Clean the vehicle body.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front pillar upper cover sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Temporarily install the front pillar upper cover sub-assembly.

1. Using a heat light, heat the vehicle body.

2. Remove the release paper from the front pillar upper cover sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Temporarily install the front pillar upper cover sub-assembly as shown in the illustration.


iii.

Engage the clips to install the front pillar upper cover sub-assembly.

HINT:

Press the front pillar upper cover sub-assembly firmly to install it.



iv.

Remove the protective tape.