Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Front Door)
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440174 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B591013N02
1.948,1.906 2.396,1.906 false 5.073,2.333 5.406,2.333 false 2.875,2.948 3.042,2.615 3.042,2.615 3.208,2.615 false 5.219,0.927 5.417,0.583 5.417,0.583 5.583,0.583 false 0.375,0.292 0.708,0.292 false 3.417,2.448 3.656,2.76 0.24,0.313 18 false 5 5.458,2.208 5.74,2.563 0.281,0.354 18 false 4 1.729,1.781 1.927,2.073 0.198,0.292 18 false 3 6.083,0.427 6.51,0.76 0.427,0.333 18 false 2 0.771,0.167 1.052,0.521 0.281,0.354 18 false 1 5.885,0.51 6.042,0.708 0.156,0.198 10 false ● 1.552,1.854 1.708,2.052 0.156,0.198 10 false ● 3.25,2.51 3.406,2.708 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REPAIR INSTRUCTION - (Click here) - -
2 NO. 3 BLACK OUT TAPE 75926 (Click here) - -
3 NO. 1 BLACK OUT TAPE 75922M (Click here) - -
4 FRONT DOOR GLASS RUN 68151C - - -
5 FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY 68210C - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. REPAIR INSTRUCTION

a.
B572068C06
4.208,1.583 4.542,1.583 false 5.313,2.063 5.583,2.333 false 1.333,1.167 1.51,0.875 false 2.01,2.24 2.333,2.5 false 3.115,3.333 2.781,3.083 false 1.5,1.865 1.688,1.979 false 4.656,1.927 4.854,2.073 false 0.74,0.219 1.073,0.458 0.333,0.24 12 false *A 3.875,0.219 4.188,0.469 0.313,0.25 12 false *B 4.021,1.5 4.333,1.656 0.313,0.156 10 false *a 5.667,2.26 5.979,2.417 0.313,0.156 10 false *b 1.917,0.583 2.125,0.75 0.208,0.167 10 false *c 4.969,1.458 5.198,1.625 0.229,0.167 10 false *d 4.083,0.708 4.396,0.865 0.313,0.156 10 false *e 5.938,1.135 6.25,1.292 0.313,0.156 10 false *f 3.615,4.229 3.927,4.385 0.313,0.156 10 false *g 4.156,3.427 4.469,3.583 0.313,0.156 10 false *h 3.438,3.094 3.75,3.25 0.313,0.156 10 false *i 2.844,3.458 3.156,3.698 0.313,0.24 10 false *j 2.771,1.417 3.083,1.573 0.313,0.156 10 false *f 0.854,0.583 1.167,0.74 0.313,0.156 10 false *e 1.146,1.073 1.458,1.229 0.313,0.156 10 false *a 2.385,2.417 2.698,2.573 0.313,0.156 10 false *b 2.604,2.99 2.917,3.146 0.313,0.156 10 false *a 0.448,0.135 0.75,0.427 0.302,0.292 18 false iv 2.188,2.865 2.49,3.156 0.302,0.292 18 false v 1.333,1.76 1.531,1.969 0.198,0.208 10 false *1 4.479,1.823 4.688,2.021 0.208,0.198 10 false *1
*A Pressing Forward *B Pulling
*1 Black Out Tape - -
*a Squeegee *b Release Paper
*c 40 to 50° *d 30 to 45°
*e 30 to 70 mm/sec. *f 10 to 20 mm
*g Hem *h First
*i Second *j Third


i.

Clean the vehicle body surface.

1. Using a heat light, heat the vehicle body surface.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


2. Wipe off any tape adhesive residue with cleaner.


ii.

Installation temperature

1. When the ambient temperature is below 15°C(59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape becomes stiff and comes off easily. When the temperature is high, the tape elasticity increases.




iii.

Before installation

1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.



iv.

Key points for handling the tape

1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

NOTICE:

Do not bend the tape or leave it in high temperature places.



v.

Key points for installation of the tape (How to use a squeegee and installation procedure for flat surfaces)

NOTICE:
·

Position the tape accurately to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms after removal.



1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body prematurely. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 30 to 70 mm (1.18 to 2.76 in.) per second.

NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.


HINT:
·

Either angle of the squeegee (pressing forward or pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.




vi.

Key points for installation of the tape (How to use a squeegee and installation procedure for hemmed surfaces)

1. If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.



vii.

Key points for installation of the tape (How to use a squeegee and installation procedure for corners)

1. Remove the release paper and apply the tape carefully with your fingers.

2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.


viii.

Check after installation

1. After completing the installation, check if the tape is installed neatly. If the tape is not installed neatly, install a new tape.

NOTICE:

Do not reuse the tape.




Hide 75926 2.INSTALL NO.3 BLACK OUT TAPE

a.
B591224N01
4.615,0.219 4.771,0.417 0.156,0.198 10 false a 0.615,0.052 1.073,0.375 0.458,0.323 18 false i, ii 3.271,0.646 3.427,0.844 0.156,0.198 10 false a 1.979,1.167 2.135,1.365 0.156,0.198 10 false c 2.177,1.563 2.333,1.76 0.156,0.198 10 false c 1.26,1.594 1.396,1.771 0.135,0.177 10 true b 1.438,1.938 1.573,2.115 0.135,0.177 10 true b 4,1.188 4.313,1.385 0.313,0.198 10 false b-b 5.438,1.156 5.75,1.354 0.313,0.198 10 false c-c 5.833,1.552 5.99,1.75 0.156,0.198 10 false C 4.406,1.792 4.563,1.99 0.156,0.198 10 false B

Standard Measurement:
Area Measurement Area Measurement
A -0.5 to 0.5mm B 2.0 to 3.0 mm
C 2.0 to 3.0 mm - -


i.

Refer to the illustration to position a new No. 3 black out tape.


ii.

Remove the release paper and install the No. 3 black out tape.



Hide 75922M 3.INSTALL NO.1 BLACK OUT TAPE

a.
B591225C01
4.969,1.021 4.781,0.813 true 6.625,0.719 6.354,0.74 true 4.99,1.01 5.302,1.167 0.313,0.156 10 false *a 6.656,0.625 6.969,0.781 0.313,0.156 10 false *a 0.594,0.042 1.021,0.385 0.427,0.344 18 false i, ii 2.677,0.417 2.802,0.625 0.125,0.208 10 true b 2.677,0.917 2.792,1.115 0.115,0.198 10 true b 3.281,1.677 3.396,1.906 0.115,0.229 10 true c 2.396,1.479 2.521,1.667 0.125,0.188 10 true c 2.427,1.698 2.552,1.885 0.125,0.188 10 true a 2.438,2.021 2.573,2.208 0.135,0.188 10 true a 4,0.083 4.354,0.302 0.354,0.219 10 false a-a 4.333,0.521 4.51,0.719 0.177,0.198 10 false A 5.75,0.083 6.104,0.302 0.354,0.219 10 false b-b 6.031,0.458 6.208,0.656 0.177,0.198 10 false B 4.021,1.417 4.375,1.635 0.354,0.219 10 false c-c 4.344,1.417 4.521,1.615 0.177,0.198 10 false D 6.646,2.49 6.823,2.646 0.177,0.156 10 false C
*a End of R - -


Standard Measurement:
Area Measurement Area Measurement
A 2.0 mm B -1.0 to 1.0 mm
C 2.0 to 6.0 mm D 4.0 mm


i.

Refer to the illustration to position a new No. 1 black out tape.


ii.

Remove the release paper and install the No. 1 black out tape.



Hide 68151C 4.INSTALL FRONT DOOR GLASS RUN

a.

Use the same procedure as for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>REASSEMBLY


Hide 68210C 5.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY