Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Rear)
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440184 WHEEL OPENING MOULDING(for Rear) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B590987N03
3.865,3.156 4.021,3.156 false 5.125,2.26 5.125,2.469 false 3.708,2.99 3.99,3.344 0.281,0.354 18 false 2 5.229,2.448 5.51,2.802 0.281,0.354 18 false 1 5.594,3.208 5.875,3.563 0.281,0.354 10 false x2 5.083,2.531 5.26,2.771 0.177,0.24 10 false ● 3.531,3.083 3.708,3.323 0.177,0.24 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY 75606B (Click here) - -
2 QUARTER PANEL WHEEL OPENING MOULDING 75874 (Click here)

● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75606B 1.REMOVE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY

Z101186

NOTICE:

When removing the quarter outside moulding sub-assembly, if the double-sided tape is difficult to remove, heat the adhesive of the quarter outside moulding sub-assembly using a heat light.



Standard:
Item Temperature
Quarter Outside Moulding sub-assembly 20 to 30°C (68 to 86°F)


CAUTION:
E306500C28
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the quarter outside moulding sub-assembly excessively.


a.
B590989C02
4.729,3.156 5.042,2.802 true 0.625,0 0.906,0.354 0.281,0.354 18 false i 4.01,0.135 4.292,0.49 0.281,0.354 18 true ii 0.49,1.969 0.708,2.229 0.219,0.26 18 true iii 3.813,1.948 4.073,2.26 0.26,0.313 18 false iv 4.531,3.094 4.729,3.271 0.198,0.177 10 true *a
*a Double-sided Tape - -
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2) - -


i.

Remove the screw and 2 clips.


ii.

Apply protective tape around the quarter outside moulding sub-assembly.


iii.

Disengage the claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:

To avoid damaging the claws, do not forcibly pull the quarter outside moulding sub-assembly.



iv.

Disengage the clips and separate the double-sided tape to remove the quarter outside moulding sub-assembly as shown in the illustration.



Hide 75874 2.REMOVE QUARTER PANEL WHEEL OPENING MOULDING

Z101186

NOTICE:

When removing the quarter panel wheel opening moulding, if the double-sided tape is difficult to remove, heat the adhesive of the quarter panel wheel opening moulding using a heat light.



Standard:
Item Temperature
Quarter Wheel Opening Moulding 20 to 30°C (68 to 86°F)


CAUTION:
E306500C28
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the quarter panel wheel opening moulding excessively.


a.
B590990C02
3.115,3.677 2.99,3.427 true 0.281,0.052 0.563,0.406 0.281,0.354 18 false i 3.813,0.167 4.094,0.521 0.281,0.354 18 true ii 2.021,2.094 2.24,2.354 0.219,0.26 18 true iii 3.031,3.688 3.219,3.865 0.188,0.177 10 true *a
*a Double-sided Tape - -
V113146

Place Hand Here
V113147

Remove in this Direction


i.

Remove the screw.


ii.

Apply protective tape around the quarter panel wheel opening moulding.


iii.

Disengage the clips and separate the double-sided tape to remove the quarter panel wheel opening moulding as shown in the illustration.