Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Rear)
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440184 WHEEL OPENING MOULDING(for Rear) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Rear)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B590987N04
3.865,3.135 4.042,3.135 false 5.417,2.573 5.583,2.573 5.583,2.573 5.729,2.01 false 3.542,3.083 3.698,3.281 0.156,0.198 10 false ● 3.708,2.99 3.927,3.313 0.219,0.323 18 false 1 5.073,2.51 5.229,2.708 0.156,0.198 10 false ● 5.24,2.438 5.458,2.76 0.219,0.323 18 false 2 5.854,3.24 6.125,3.417 0.271,0.177 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 QUARTER PANEL WHEEL OPENING MOULDING 75874 (Click here) - -
2 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY 75606B (Click here) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75874 1.INSTALL QUARTER PANEL WHEEL OPENING MOULDING

Z101186

NOTICE:

When installing a new quarter panel wheel opening moulding, heat the vehicle body using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.
B591201C03
4.979,0.938 5.26,1.167 true 0.563,0.073 0.844,0.427 0.281,0.354 18 false i 4.052,0.073 4.333,0.427 0.281,0.354 18 false ii 5.271,1.104 5.469,1.271 0.198,0.167 10 true *a 4.448,1.198 4.635,1.5 0.188,0.302 18 true iii 1.813,1.969 2.094,2.323 0.281,0.354 18 false iv
*a Double-sided Tape - -
V113147

Install in this Direction - -


i.

Clean the vehicle body.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the quarter panel wheel opening moulding with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new quarter panel wheel opening moulding.

1. Using a heat light, heat the vehicle body.

2. Remove the release paper from the quarter panel wheel opening moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Engage the clip to install the quarter panel wheel opening moulding.

HINT:

Press the quarter panel wheel opening moulding firmly to install it.



iii.

Remove the protective tape.


iv.

Install the screw.



Hide 75606B 2.INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY

Z101186

NOTICE:

When installing a new quarter outside moulding sub-assembly , heat the vehicle body using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.
B591202C04
5.49,0.729 5.542,1.083 true 0.563,0.115 0.844,0.469 0.281,0.354 18 false i 4.021,0.104 4.302,0.458 0.281,0.354 18 false ii 5.5,1.063 5.688,1.24 0.188,0.177 10 true *a 6.625,0.75 6.896,1.083 0.271,0.333 18 true iii 1.885,2 2.156,2.333 0.271,0.333 18 true iv
*a Double-sided Tape - -
V113147

Install in this Direction - -


i.

Clean the vehicle body.

1. Using a heat light, heat the vehicle body surface.

2. Remove any remaining double-sided tape from the vehicle body.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the quarter outside moulding sub-assembly with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new quarter outside moulding sub-assembly.

1. Using a heat light, heat the vehicle body.

2. Remove the release paper from the quarter outside moulding sub-assembly.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Engage the clips and claws to install the quarter outside moulding sub-assembly.

HINT:

Press the quarter outside moulding sub-assembly firmly to install it.



iii.

Remove the protective tape.


iv.

Install the screw and 2 clips.