| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | HEADLIGHT LEVELING MOTOR | 85662 | ( )
|
- | - |
| 2 | HEADLIGHT LEVELING MOTOR BASE PACKING | 85669 | ( )
|
- | - |
| 3 | NO. 1 HEADLIGHT COVER | 81144 | - | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 4 | HEADLIGHT LENS SUB-ASSEMBLY | 8110B | ( )
|
- | - |
| 5 | HEADLIGHT LENS GASKET | 81132B | ( )
|
- | - |
| 6 | LIGHT CONTROL LED ECU | 85967D | ( )
|
- | - |
| 7 | HEADLIGHT UNIT | 81171A | ( )
|
- | - |
| *1 | HEADLIGHT HOUSING SUB-ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>PRECAUTION
Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.
Do not reuse parts which have reduced fastening ability due to thread damage.
Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
When installing components, make sure that the wire harness is not pinched or pulled.
Do not use solvent to clean components. Only clean them with a dry cloth.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
85662
1.REMOVE HEADLIGHT LEVELING MOTOR
|
Turn |
|
Remove in this Direction |
Turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight unit.
Make sure to remember the number of aiming screw rotations.
Remove the headlight leveling motor as shown in the illustration.
85669
2.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING
|
|
81144
3.REMOVE NO. 1 HEADLIGHT COVER
|
Remove in this Direction | - | - |
8110B
4.REMOVE HEADLIGHT LENS SUB-ASSEMBLY
| *a | "TORX" Screw | - | - |
Disconnect the connector.
Make sure to wear clean rubber gloves when performing this procedure.
Prevention of static electricity is required during this procedure.
Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
Using a T20H "TORX" driver, remove the "TORX" screw.
Remove the 7 screws.
Using a hair dryer, heat the backside of the headlight assembly.
Do not heat the backside of the headlight lens sub-assembly above 120 °C (248 °F).
If the headlight assembly is heated unevenly, it will deform or melt.
Disengage the claws to remove the headlight lens sub-assembly.
If the headlight lens sub-assembly cannot be separated even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens sub-assembly. Be careful not to damage the headlight lens sub-assembly and headlight housing sub-assembly.
81132B
5.REMOVE HEADLIGHT LENS GASKET
|
|
85967D
6.REMOVE LIGHT CONTROL LED ECU
|
|
81171A
7.REMOVE HEADLIGHT UNIT
|
|
|
Turn |
|
Remove in this Direction |
Disconnect the connector.
Disengage the claws and clamp.
While holding the headlight unit by hand, turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit.
Make sure to remember the number of aiming screw rotations.
Remove the headlight unit from the headlight housing sub-assembly as shown in the illustration.