Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Headlight) › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0440190 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
E460601N02
3.292,1.479 3.615,1.479 false 1.469,2.365 1.635,2.365 1.635,2.365 1.885,2.281 false 4.833,2.771 5,2.771 5,2.771 5.167,2.688 false 2.375,3.938 2.552,4.104 2.552,4.104 2.719,4.104 false 5.698,1.531 5.875,1.698 5.875,1.698 6.042,1.698 false 3.083,1.323 3.365,1.677 0.281,0.354 18 false 2 1.25,2.208 1.531,2.563 0.281,0.354 18 false 3 4.635,2.594 4.917,2.948 0.281,0.354 18 false 1 3.021,3.917 3.302,4.271 0.281,0.354 18 false 4 6.135,1.583 6.448,1.781 0.313,0.198 10 false *1 3.427,3.323 3.74,3.521 0.313,0.198 10 false x7 1.115,2.25 1.271,2.448 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HEADLIGHT UNIT 81171A (Click here) - -
2 LIGHT CONTROL LED ECU 85967D (Click here) - -
3 HEADLIGHT LENS GASKET 81132B (Click here) - -
4 HEADLIGHT LENS SUB-ASSEMBLY 8110B (Click here) - -

*1 HEADLIGHT HOUSING SUB-ASSEMBLY - -
● Non-reusable part - -

E453823N01
4.844,1.146 5.01,1.146 5.01,1.146 5.135,0.813 false 2.854,0.365 3.188,0.365 false 5.948,1.115 5.948,0.938 5.948,0.938 6,0.667 false 4.469,1.021 4.75,1.375 0.281,0.354 10 false ● 6.01,1.125 6.292,1.479 0.281,0.354 18 false 7 4.635,0.969 4.917,1.323 0.281,0.354 18 false 6 3.271,0.208 3.552,0.563 0.281,0.354 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 1 HEADLIGHT COVER 81144 - - -
6 HEADLIGHT LEVELING MOTOR BASE PACKING 85669 - - -
7 HEADLIGHT LEVELING MOTOR 85662 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81171A 1.INSTALL HEADLIGHT UNIT

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit assembly or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit assembly with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E448023C01
0.365,0.104 0.646,0.458 0.281,0.354 18 false i 4.031,0.063 4.208,0.344 0.177,0.281 18 false ii 1.635,1.969 2.198,2.26 0.563,0.292 18 false iii, iv
V100135

Turn
V113147

Install in this Direction


i.

Temporarily install the headlight unit to the headlight housing sub-assembly.


ii.

While holding the headlight unit by hand, turn the aiming screw.

NOTICE:

Turn the aiming screw the same number of times as they were turned during removal.



iii.

Engage the claws and clamp.


iv.

Connect the connector.



Hide 85967D 2.INSTALL LIGHT CONTROL LED ECU

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit assembly or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit assembly with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




a.
E448027


Hide 81132B 3.INSTALL HEADLIGHT LENS GASKET

Z101186

NOTICE:
·

The headlight lens gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




a.
E460583C01
4.479,1 4.729,0.885 false 5.083,1.135 5.333,1.021 false 1.021,0.125 1.229,0.479 0.208,0.354 18 false i 4.313,0.073 5.104,0.448 0.792,0.375 18 false ii, iii 4.417,0.604 4.625,0.958 0.208,0.354 10 false 2 5.51,0.5 5.719,0.854 0.208,0.354 10 false 1 4.281,0.896 4.5,1.063 0.219,0.167 10 false *b 4.875,1.042 5.094,1.208 0.219,0.167 10 false *a 6.521,0.979 6.854,1.313 0.333,0.333 18 false iv 1.99,1.948 2.281,2.24 0.292,0.292 18 false vii 2.469,4.323 2.688,4.49 0.219,0.167 10 false *c 3.146,4.156 3.438,4.448 0.292,0.292 18 false v 5.104,3.531 5.479,3.854 0.375,0.323 18 false vi
*a Release Paper *b Tape
*c 20mm - -


i.

Clean the installation groove of the headlight lens sub-assembly.


ii.

Partially remove the release paper from a new headlight lens gasket, and cut off a piece of it.


iii.

Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.


iv.

Using scissors, cut the end of the headlight lens gasket at a 45° angle.


v.

Install a new headlight lens gasket as shown in the illustration.

NOTICE:

Gently install the headlight lens gasket without pulling it.



vi.

Using a screwdriver with their tips wrapped with release paper, completely press the headlight lens gasket into the groove to install it.

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly.




vii.

Check the installation condition of the headlight lens gasket.

NOTICE:
·

Make sure the headlight lens gasket is not protruding and is installed properly.

·

Make sure there is no gap between the ends of the headlight lens gasket.





Hide 8110B 4.INSTALL HEADLIGHT LENS SUB-ASSEMBLY

a.
E460590C01
1.177,0.083 1.458,0.438 0.281,0.354 18 false i 0.49,1.927 0.771,2.281 0.281,0.354 18 false iii 4.135,0.083 4.417,0.438 0.281,0.354 18 false ii 2.979,1.927 3.26,2.281 0.281,0.354 18 false iv 3.167,2.281 3.479,2.479 0.313,0.198 10 false *a 4.021,1.958 4.302,2.313 0.281,0.354 18 false v
*a "TORX" Screw - -


i.

Clean the sealing surface of the headlight lens sub-assembly.

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens sub-assembly.

·

Do not touch the headlight lens sub-assembly with bare hands.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens sub-assembly, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




ii.

Engage the claws to install the headlight lens sub-assembly to the headlight housing sub-assembly.


iii.

Install the 7 screws.


iv.

Using a T20H "TORX" driver, install the "TORX" screw.


v.

Connect the connector.

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Make sure to wear clean rubber gloves when performing this procedure.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)



Hide 81144 5.INSTALL NO. 1 HEADLIGHT COVER

Hide 85669 6.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

Hide 85662 7.INSTALL HEADLIGHT LEVELING MOTOR

a.
E448031C02
0.365,0.01 0.646,0.365 0.281,0.354 18 false i 4.052,0.031 4.333,0.385 0.281,0.354 18 false ii
V100135

Turn
V113147

Install in this Direction


i.

Install the headlight leveling motor as shown in the illustration.


ii.

Turn the aiming screw as shown in the illustration.

NOTICE:

Turn the aiming screw the same number of times as they were turned during removal.