Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Halogen Headlight) › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0440207 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
E447970N03
2.406,1.167 2.74,1.167 false 5.771,0.542 6.104,0.542 false 4.802,0.781 4.917,1.021 4.917,1.021 5.083,1.021 false 5.354,1.969 5.438,2.208 5.438,2.208 5.604,2.208 false 6.344,1.542 6.677,1.542 false 2.823,0.958 3.104,1.313 0.281,0.354 18 false 1 5.917,2.052 6.198,2.406 0.281,0.354 18 false 2 6.771,1.344 7.052,1.698 0.281,0.354 18 false 3 6.385,0.365 6.667,0.719 0.281,0.354 18 false 4 5.5,0.854 5.781,1.208 0.281,0.354 18 false 5 5.354,0.906 5.708,1.125 0.354,0.219 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CLEARANCE LIGHT LED 81161 - - -
2 NO. 1 HEADLIGHT BULB 81110B (Click here) - -
3 HEADLIGHT BACK COVER - - - -
4 HEADLIGHT LEVELING MOTOR 85662 (Click here) - -
5 HEADLIGHT LEVELING MOTOR BASE PACKING 85669 (Click here) - -

● Non-reusable part - -

E460599N01
3.063,5.083 2.896,5.083 2.896,5.083 2.844,4.979 false 5.021,4.625 5.188,4.625 5.188,4.625 5.292,4.865 false 1.583,3.104 1.844,3.104 false 5.49,1.583 5.656,2.083 5.656,2.083 5.823,2.083 false 3.365,4.854 3.646,5.208 0.281,0.354 18 false 6 1.375,2.927 1.656,3.188 0.281,0.26 18 false 7 1.208,2.979 1.396,3.156 0.188,0.177 10 false ● 4.844,4.458 5.125,4.719 0.281,0.26 18 false 8 4.146,4.01 4.365,4.229 0.219,0.219 10 false x7 5.885,1.938 6.167,2.198 0.281,0.26 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

6 HEADLIGHT LENS SUB-ASSEMBLY 8110B (Click here) - -
7 HEADLIGHT LENS GASKET 81132B (Click here) - -
8 HEADLIGHT UNIT 81171A (Click here) - -

*1 HEADLIGHT HOUSING SUB-ASSEMBLY - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>PRECAUTION

·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81161 1.REMOVE CLEARANCE LIGHT LED

a.
E449966


Hide 81110B 2.REMOVE NO. 1 HEADLIGHT BULB

Z101186

NOTICE:

Do not touch the No. 1 headlight bulb glass with your fingers.



a.
E447988


Hide 3.REMOVE HEADLIGHT BACK COVER

a.
E447989


Hide 85662 4.REMOVE HEADLIGHT LEVELING MOTOR

a.
E447990C02
0.365,0.01 0.656,0.365 0.292,0.354 18 false i 3.667,0.021 3.958,0.375 0.292,0.354 18 false ii
V100135

Turn
V113147

Remove in this Direction


i.

Turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit.

NOTICE:

Make sure to remember the number of aiming screw rotations.



ii.

Remove the headlight leveling motor as shown in the illustration.



Hide 85669 5.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

Z101186

NOTICE:

The headlight leveling motor base packing must not be reused.



a.
E447991


Hide 8110B 6.REMOVE HEADLIGHT LENS SUB-ASSEMBLY

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




a.
E460586C01
3.01,0.521 3.292,0.875 0.281,0.354 18 false i 0.188,0.24 0.469,0.594 0.281,0.354 18 false ii 4.052,0.365 4.333,0.719 0.281,0.354 18 false iii 3.156,0.813 3.469,1.01 0.313,0.198 10 false *a 1.875,2.969 2.427,3.323 0.552,0.354 18 false iv
*a "TORX" Screw - -


i.

Using a T20H "TORX" driver, remove the "TORX" screw.


ii.

Remove the 7 screws.


iii.

Using a dryer, heat the backside of the headlight assembly.

NOTICE:
·

Do not heat the backside of the headlight lens sub-assembly above 120 °C (248 °F).

·

If the headlight assembly is heated unevenly, it will deform or melt.




iv.

Disengage the claws to remove the headlight lens sub-assembly.

NOTICE:

If the headlight lens sub-assembly cannot be removed even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens sub-assembly. Be careful not to damage the headlight lens sub-assembly and headlight housing sub-assembly.




Hide 81132B 7.REMOVE HEADLIGHT LENS GASKET

Z101186

NOTICE:

Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.



a.
E447993


Hide 81171A 8.REMOVE HEADLIGHT UNIT

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit assembly or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit assembly with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E447995C01
0.396,0.042 0.677,0.396 0.281,0.354 18 false i 4.042,0.042 4.323,0.396 0.281,0.354 18 false ii 3.958,1.885 4.24,2.24 0.281,0.354 18 false iv 0.365,1.979 0.646,2.333 0.281,0.354 18 false iii
V100135

Turn
V113147

Remove in this Direction


i.

Disengage the claws.


ii.

Disengage the clamp and claws.


iii.

While holding the headlight unit by hand, turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit.

NOTICE:

Make sure to remember the number of aiming screw rotations.



iv.

Remove the headlight unit from the headlight housing sub-assembly as shown in the illustration.