Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Halogen Headlight) › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0440207 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
E460599N02
1.573,3.115 1.823,3.115 false 5,4.594 5.188,4.594 5.188,4.594 5.25,4.844 false 3.052,5.083 2.885,5.083 2.885,5.083 2.833,4.958 false 5.76,2.052 5.594,2.052 5.594,2.052 5.458,1.604 false 4.115,4.052 4.333,4.219 0.219,0.167 10 false x7 4.823,4.427 5.031,4.698 0.208,0.271 18 false 1 1.219,2.948 1.396,3.125 0.177,0.177 10 false ● 1.375,2.906 1.583,3.177 0.208,0.271 18 false 2 5.813,1.927 6.021,2.198 0.208,0.271 10 false *1 3.354,4.854 3.563,5.125 0.208,0.271 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 HEADLIGHT UNIT 81171A (Click here) - -
2 HEADLIGHT LENS GASKET 81132B (Click here) - -
3 HEADLIGHT LENS SUB-ASSEMBLY 8110B (Click here) - -

*1 HEADLIGHT HOUSING SUB-ASSEMBLY - -
● Non-reusable part - -

E452420N02
5.74,0.563 6.073,0.563 false 6.354,1.615 6.688,1.615 false 5.344,1.958 5.448,2.229 5.448,2.229 5.615,2.229 false 4.781,0.781 4.885,1.063 4.885,1.063 5.052,1.063 false 2.396,1.094 2.729,1.094 false 2.813,0.917 3.156,1.271 0.344,0.354 18 false 8 5.927,2.063 6.313,2.448 0.385,0.385 18 false 7 6.771,1.448 7.135,1.823 0.365,0.375 18 false 6 6.396,0.406 6.823,0.792 0.427,0.385 18 false 5 5.281,0.885 5.563,1.24 0.281,0.354 18 false 4 5.125,0.938 5.406,1.292 0.281,0.354 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

4 HEADLIGHT LEVELING MOTOR BASE PACKING 85669 - - -
5 HEADLIGHT LEVELING MOTOR 85662 (Click here) - -
6 HEADLIGHT BACK COVER - - - -
7 NO. 1 HEADLIGHT BULB 81110B (Click here) - -
8 CLEARANCE LIGHT LED 81161 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 81171A 1.INSTALL HEADLIGHT UNIT

Z101186

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit assembly or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit assembly with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E447997C01
0.385,0.083 0.667,0.438 0.281,0.354 18 false i 4.042,0.073 4.323,0.427 0.281,0.354 18 false ii 3.958,1.865 4.24,2.219 0.281,0.354 18 false iv 0.323,1.917 0.604,2.271 0.281,0.354 18 false iii
V100135

Turn
V113147

Install in this Direction


i.

Temporarily install the headlight unit as shown in the illustration.


ii.

While holding the headlight unit by hand, turn the aiming screws as shown in the illustration to install the headlight unit.

NOTICE:

Turn the aiming screws the same number of times as they were turned during removal.



iii.

Engage the clamp and claws.


iv.

Engage the claws.



Hide 81132B 2.INSTALL HEADLIGHT LENS GASKET

Z101186

NOTICE:
·

The headlight lens gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




a.
E460511C01
4.385,0.99 4.729,0.875 false 5,1.135 5.344,1.021 false 1.031,0.083 1.313,0.438 0.281,0.354 18 false i 4.302,0.094 5.146,0.417 0.844,0.323 18 false ii, iii 4.417,0.625 4.698,0.979 0.281,0.354 10 false 2 5.542,0.5 5.823,0.854 0.281,0.354 10 false 1 6.521,0.958 6.854,1.292 0.333,0.333 18 false iv 4.135,0.885 4.448,1.083 0.313,0.198 10 false *b 4.802,1.021 5.115,1.219 0.313,0.198 10 false *a 1.99,1.948 2.271,2.302 0.281,0.354 18 false vii 2.5,4.292 2.729,4.479 0.229,0.188 10 false *c 3.146,4.146 3.427,4.5 0.281,0.354 18 false v 5.094,3.479 5.448,3.844 0.354,0.365 18 false vi
*a Release Paper *b Tape
*c 20mm - -


i.

Clean the installation groove of the headlight lens sub-assembly.


ii.

Partially remove the release paper from a new headlight lens gasket, and cut off a piece of it.


iii.

Fold the release paper over the tip of a screwdriver and secure it in place with tape as indicated by the arrows, in the order shown in the illustration.


iv.

Using scissors, cut the end of the headlight lens gasket at a 45° angle.


v.

Install a new headlight lens gasket as shown in the illustration.

NOTICE:

Gently install the headlight lens gasket without pulling it.



vi.

Using a screwdriver with their tips wrapped with release paper, completely press the headlight lens gasket into the groove to install it.

NOTICE:
·

Gently install the headlight lens gasket without pulling it.

·

If the headlight lens gasket is pulled while it is installed, it will not be installed properly.




vii.

Check the installation condition of the headlight lens gasket.

NOTICE:
·

Make sure the headlight lens gasket is not protruding and is installed properly.

·

Make sure there is no gap between the ends of the headlight lens gasket.





Hide 8110B 3.INSTALL HEADLIGHT LENS SUB-ASSEMBLY

a.
E460587C01
3.563,0.125 3.844,0.479 0.281,0.354 18 false ii 1.031,0.115 1.313,0.469 0.281,0.354 18 false i 4.896,2.396 5.177,2.75 0.281,0.354 18 false iv 5.021,2.708 5.333,2.906 0.313,0.198 10 false *a 1.844,2.313 2.396,2.667 0.552,0.354 18 false iii
*a "TORX" Screw - -


i.

Clean the sealing surface of the headlight lens sub-assembly.

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens sub-assembly, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.




ii.

Engage the claws to install the headlight lens sub-assembly to the headlight housing sub-assembly.


iii.

Install the 7 screws.


iv.

Using a T20H "TORX" driver, install the "TORX" screw.



Hide 85669 4.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

Hide 85662 5.INSTALL HEADLIGHT LEVELING MOTOR

a.
E448000C02
0.385,0.021 0.667,0.375 0.281,0.354 18 false i 4.031,0.021 4.313,0.375 0.281,0.354 18 false ii
V100135

Turn
V113147

Install in this Direction


i.

Install the headlight leveling motor as shown in the illustration.


ii.

Turn the aiming screw as shown in the illustration.

NOTICE:

Turn the aiming screw the same number of times as they were turned during removal.




Hide 6.INSTALL HEADLIGHT BACK COVER

Hide 81110B 7.INSTALL NO. 1 HEADLIGHT BULB

Z101186

NOTICE:

Do not touch the No. 1 headlight bulb glass with your fingers.



Hide 81161 8.INSTALL CLEARANCE LIGHT LED