Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL MAIN VALVE › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093308 M15A-FKS FUEL _0440420 FUEL MAIN VALVE A

M15A-FKS FUEL  FUEL MAIN VALVE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A458687N02
1.75,1.021 2.083,1.021 false 4.729,1.615 4.729,1.948 false 5.365,1.458 5.365,1.792 false 5.948,1.375 5.948,1.708 false 4.667,2.021 4.823,2.219 0.156,0.198 10 false ● 5.292,1.802 5.573,2.156 0.281,0.354 18 false 3 5.875,1.719 6.156,2.073 0.281,0.354 18 false 2 1.521,0.885 1.802,1.24 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 77020A - - -
2 NO. 2 FUEL SUCTION SUPPORT - - - -
3 FUEL MAIN VALVE ASSEMBLY 23070 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel main valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 2.REMOVE NO. 2 FUEL SUCTION SUPPORT

a.
A459585


Hide 23070 3.REMOVE FUEL MAIN VALVE ASSEMBLY

a.
A459668