Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD
RM3700E _51 Engine / Hybrid System _093330 M15A-FKS ENGINE MECHANICAL _0440541 CYLINDER HEAD G

M15A-FKS ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 11101 1.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly, intake manifold and exhaust manifold.

A459093C01
3.823,0.271 4.135,0.427 0.313,0.156 10 false *a 3.833,1.896 4.146,2.052 0.313,0.156 10 false *b 3.833,2.813 4.146,2.969 0.313,0.156 10 false *c
*a Bottom Side *b Intake Manifold Side
*c Exhaust Manifold Side - -


Maximum Warpage:
Item Specified Condition
Bottom side 0.05 mm
0.00197 in.
Intake manifold side 0.10 mm
0.00394 in.
Exhaust manifold side 0.10 mm
0.00394 in.


HINT:

If the warpage is more than the maximum, replace the cylinder head sub-assembly.



b.
A459094

Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.

HINT:

If cracks are found, replace the cylinder head sub-assembly.



Hide 13711M 2.INSPECT INTAKE COMPRESSION SPRING

a.
A400450

Using a vernier caliper, measure the free length of the compression spring.

Standard Free Length:
Specified Condition
61.92 mm
2.438 in.


NOTICE:

Compression springs come in 2 different lengths. Make sure all compression springs are the same length when replacing them.



b.
A400451C01
1.635,0.208 1.948,0.406 0.313,0.198 10 false *a 0.948,1.302 1.26,1.5 0.313,0.198 10 false *b
*a Deviation
*b 37 mm (1.46 in.)


Using a steel square, measure the deviation of the compression spring.

Maximum Deviation (Reference):
Specified Condition
1.0 mm
0.0394 in.


HINT:

If the deviation is more than the maximum, replace the compression spring.



Hide 13715H 3.INSPECT EXHAUST COMPRESSION SPRING

a.
A400450

Using a vernier caliper, measure the free length of the compression spring.

Standard Free Length:
Specified Condition
61.92 mm
2.438 in.


NOTICE:

Compression springs come in 2 different lengths. Make sure all compression springs are the same length when replacing them.



b.
A400451C01
1.635,0.208 1.948,0.406 0.313,0.198 10 false *a 0.948,1.302 1.26,1.5 0.313,0.198 10 false *b
*a Deviation
*b 37 mm (1.46 in.)


Using a steel square, measure the deviation of the compression spring.

Maximum Deviation (Reference):
Specified Condition
1.0 mm
0.0394 in.


HINT:

If the deviation is more than the maximum, replace the compression spring.



Hide 13711 4.INSPECT INTAKE VALVE

a.
A400452

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:
Specified Condition
5.470 to 5.485 mm
0.215 to 0.216 in.


HINT:

If the valve stem diameter is not as specified, check the intake valve guide bush oil clearance.



b.
A400453C01
0.969,1.396 1.281,1.594 0.313,0.198 10 false *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:
Minimum Margin Thickness Specified Condition
0.5 mm
0.0197 in.
1.0 mm
0.0394 in.


HINT:

If the margin thickness is less than the minimum, replace the intake valve.



c.
A400454C01
2.479,1.063 2.792,1.26 0.313,0.198 10 false *a
*a Overall Length


Using a vernier caliper, measure the overall length of the intake valve.

Standard Overall Length:
Minimum Margin Thickness Specified Condition
101.95 mm
4.01 in.
102.45 mm
4.03 in.


HINT:

If the overall length is less than the minimum, replace the intake valve.



Hide 13715 5.INSPECT EXHAUST VALVE

a.
A400455

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:
Specified Condition
5.465 to 5.480 mm
0.215 to 0.216 in.


HINT:

If the valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.



b.
A400456C01
0.969,1.594 1.281,1.792 0.313,0.198 10 false *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:
Minimum Margin Thickness Specified Condition
0.5 mm
0.0197 in.
1.0 mm
0.0394 in.


HINT:

If the margin thickness is less than the minimum, replace the exhaust valve.



c.
A400457C01
2.385,1.125 2.698,1.323 0.313,0.198 10 false *a
*a Overall Length


Using a vernier caliper, measure the overall length of the exhaust valve.

Standard Overall Length:
Minimum Margin Thickness Specified Condition
105.9 mm
4.17 in.
106.4 mm
4.19 in.


HINT:

If the overall length is less than the minimum, replace the exhaust valve.



Hide 6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A459095

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.51 to 5.53 mm (0.217 to 0.218 in.)

Specified Condition
5.51 to 5.53 mm
0.217 to 0.218 in.



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Maximum Oil Clearance Specified Condition
Intake Side 0.080 mm
0.00315 in.
0.025 to 0.060 mm
0.000984 to 0.00236 in.
Exhaust Side 0.10 mm
0.00394 in.
0.030 to 0.065 mm
0.00118 to 0.00256 in.


HINT:
·

Oil clearance = Valve guide bush inside - Valve stem diameter

·

If the oil clearance is more than the maximum, replace the valve and valve guide bush.




Hide 7.INSPECT INTAKE VALVE SEAT

Pre-procedure1

a.

Apply a light coat of Prussian blue to the valve face.


b.
A459096C01
1.5,1.531 1.813,1.688 0.313,0.156 10 false *a
*a Width


Lightly press the valve face against the intake valve seat.

NOTICE:

Do not rotate the valve while pressing it.



Procedure1

a.

Check the valve face and intake valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the intake valve.



ii.

If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the intake valve seat.



iii.

Measure the width of the contact area of the intake valve seat and valve face.

Standard Width:
Specified Condition
1.0 to 1.4 mm
0.0394 to 0.0551 in.




Post-procedure1

a.

None


Hide 8.INSPECT EXHAUST VALVE SEAT

Pre-procedure1

a.

Apply a light coat of Prussian blue to the valve face.


b.
A459097C01
1.406,1.708 1.625,1.917 0.219,0.208 10 true *a
*a Width


Lightly press the valve face against the exhaust valve seat.

NOTICE:

Do not rotate the valve while pressing it.



Procedure1

a.

Check the valve face and exhaust valve seat by using the following procedure:

i.

If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the exhaust valve.



ii.

If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the exhaust valve seat.



iii.

Measure the width of the contact area of the exhaust valve seat and valve face.

Standard Width:
Specified Condition
1.2 to 1.6 mm
0.0472 to 0.0630 in.




Post-procedure1

a.

None


Hide 9.INSPECT CAMSHAFT THRUST CLEARANCE

Pre-procedure1

a.

Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps, No. 4 camshaft bearing cap, camshaft housing sub-assembly and camshaft journals.


b.

Place the intake camshaft sub-assembly and exhaust camshaft sub-assembly on the camshaft housing sub-assembly on the cylinder head sub-assembly.


c.

Install the camshaft bearing caps.

HINT:

Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY



d.

Install the camshaft housing sub-assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY



Procedure1

a.
A459098

Using a dial indicator, measure the thrust clearance while moving the intake camshaft sub-assembly and exhaust camshaft sub-assembly back and forth.

Standard Thrust Clearance:
Item Maximum Thrust Clearance Specified Condition
Intake camshaft sub-assembly 0.22 mm
0.00866 in.
0.04 to 0.17 mm
0.00157 to 0.00669 in.
Exhaust camshaft sub-assembly 0.22 mm
0.00866 in.
0.04 to 0.17 mm
0.00157 to 0.00669 in.


HINT:

If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly. If the thrust surface is damaged, replace the camshaft.



Post-procedure1

a.

None