Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › ENGINE UNIT
RM3700E _51 Engine / Hybrid System _093330 M15A-FKS ENGINE MECHANICAL _0440540 ENGINE UNIT A

M15A-FKS ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
A478874N01
4.781,3.188 5.75,3.354 0.969,0.167 2.25,0.417 3.313,0.583 1.063,0.167 2.708,1.042 3.708,1.208 1,0.167 3.417,5.208 4.5,5.375 1.083,0.167 2.083,1.25 2.583,1.99 0.5,0.74 5.75,3.281 6.667,3.281 false 3.479,4.802 3.646,4.802 3.646,4.802 3.885,4.5 false 4.5,5.292 5.156,5.292 false 1.823,2 2.083,0.5 2.083,0.5 2.25,0.5 false 2.302,1.938 2.542,1.115 2.542,1.115 2.708,1.115 false 5.573,0.198 5.823,0.198 false 1.74,3.042 1.74,3.625 false 1.792,3.604 2.073,3.958 0.281,0.354 18 false 1 3.281,4.667 3.563,5.021 0.281,0.354 18 false 2 4.104,1 4.385,1.354 0.281,0.354 18 false 3 3.156,5.156 3.438,5.51 0.281,0.354 18 false 3 4.531,3.135 4.813,3.49 0.281,0.354 18 false 3 3.708,0.354 3.99,0.708 0.281,0.354 18 false 3 5.344,0.042 5.625,0.396 0.281,0.354 18 false 2 4.802,3.188 5.802,3.365 1,0.177 8 false 6.5 (66, 58 in.*lbf) 2.281,0.417 3.438,0.583 1.156,0.167 8 false 9.8 (100, 87 in.*lbf) 2.74,1.052 3.823,1.26 1.083,0.208 8 false 4.0 (41, 35 in.*lbf) 3.49,5.219 4.74,5.385 1.25,0.167 8 false 4.0 (41, 35 in.*lbf) 3.083,4.75 3.365,5.104 0.281,0.354 10 false ● 5.177,0.083 5.458,0.438 0.281,0.354 10 false ● 3.906,4.5 4.219,4.698 0.313,0.198 10 false x6 5.917,0.219 6.229,0.417 0.313,0.198 10 false x8 1.792,2.927 2.104,3.125 0.313,0.198 10 false x2 5.24,5.292 5.552,5.49 0.313,0.198 10 false x2 2.094,1.26 2.469,1.5 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STRAIGHT PIN - (Click here) - -
2 RING PIN - (Click here) - -
3 STUD BOLT - (Click here) - -

*A w/ Stud Bolt - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part

A461157N02
2.083,0.125 2.844,0.292 0.76,0.167 5.25,0.333 5.917,0.5 0.667,0.167 1.583,4.667 2.417,4.833 0.833,0.167 2.417,5.531 3.135,5.698 0.719,0.167 1.24,1.771 2,1.938 0.76,0.167 1.5,3.167 2.25,3.333 0.75,0.167 2.417,3.875 3.083,4.042 0.667,0.167 4.833,3 5.542,3.167 0.708,0.167 4.417,5 5.083,5.167 0.667,0.167 1.667,5.146 2.333,5.313 0.667,0.167 6.052,5.021 6.75,5.188 0.698,0.167 0.948,4.167 1.75,4.333 0.802,0.167 1.573,2.75 2.333,2.917 0.76,0.167 1.542,4.625 2.458,4.875 0.917,0.25 0.906,4.125 1.792,4.375 0.885,0.25 2.844,0.208 3.542,0.208 false 4.781,0.417 5.25,0.417 false 2,1.854 2.552,1.854 false 2.958,1.01 3.375,1.01 false 4.958,0.958 5.375,0.958 false 4.979,2.271 5.583,1.917 5.583,1.917 5.75,1.917 false 3.969,4.5 4.385,4.5 false 3.667,3.646 3.781,4 3.781,4 3.948,4 false 5.75,3.417 5.75,3.167 false 3.625,5.448 3.313,5.615 3.313,5.615 3.146,5.615 false 6,4.552 6,4.385 6,4.385 5.885,4.24 false 6.25,4.083 6.667,4.083 false 3.208,5.115 3.625,5.115 false 2.333,2.833 2.917,2.833 false 2.333,5.229 2.5,5.229 2.5,5.229 2.76,4.708 false 3.104,3.542 3.104,3.375 3.104,3.375 3.646,3.219 false 3.083,3.958 3.552,3.958 false 4.5,3.375 4.667,3.083 4.667,3.083 4.833,3.083 false 4,5.083 4.417,5.083 false 5.385,4.708 5.875,5.104 5.875,5.104 6.042,5.104 false 1.063,3.802 1.302,4 1.302,4 1.302,4.167 false 1.917,3.667 1.917,4.667 false 2.25,3.25 2.417,3.25 2.417,3.25 2.698,3.688 false 2.135,0.125 2.938,0.375 0.802,0.25 8 false 29 (296, 21) 5.281,0.333 6,0.583 0.719,0.25 8 false 10 (102, 7) 1.031,1.708 1.313,2.063 0.281,0.354 18 false 4 2.75,0.885 3.031,1.24 0.281,0.354 18 false 5 5.438,0.833 5.719,1.188 0.281,0.354 18 false 6 6.167,1.75 6.448,2.104 0.281,0.354 18 false 7 6.094,4.552 6.375,4.906 0.281,0.354 18 false 8 4.26,3.844 4.542,4.198 0.281,0.354 18 false 9 4.792,4.344 5.125,4.708 0.333,0.365 18 false 10 2.125,5.49 2.646,5.781 0.521,0.292 18 false 11 1.208,4.583 1.708,4.917 0.5,0.333 18 false 12 0.563,4.094 0.938,4.396 0.375,0.302 18 false 13 5.875,3.479 6.313,3.802 0.438,0.323 18 false 14 5.708,3.552 5.969,3.854 0.26,0.302 10 false ● 1.646,4.677 2.625,4.906 0.979,0.229 8 false 29.5 (301, 22) 2.448,5.542 3.198,5.74 0.75,0.198 8 false 40 (408, 30) 6.719,3.969 6.979,4.271 0.26,0.302 10 false ● 3.031,5 3.292,5.302 0.26,0.302 10 false ● 1.271,1.771 1.99,2.021 0.719,0.25 8 false 44 (449, 32) 3.042,3.583 3.302,3.885 0.26,0.302 10 false ● 0.969,4.167 1.802,4.417 0.833,0.25 8 false 17.5 (178, 13) 3.615,0.229 3.875,0.531 0.26,0.302 10 false x4 4.792,0.417 5.052,0.719 0.26,0.302 10 false x5 5.438,4.542 5.698,4.844 0.26,0.302 10 false x2 2.844,4.594 3.104,4.896 0.26,0.302 10 false x2 4.01,5.083 4.271,5.385 0.26,0.302 10 false x9 3.031,2.781 3.292,3.083 0.26,0.302 10 false x4 4.521,3.427 4.781,3.729 0.26,0.302 10 false x3 1.615,2.76 2.333,3.01 0.719,0.25 8 false 43 (438, 32) 1.542,3.167 2.26,3.417 0.719,0.25 8 false 43 (438, 32) 4.854,3 5.573,3.25 0.719,0.25 8 false 43 (438, 32) 6.115,5.021 6.833,5.271 0.719,0.25 8 false 10 (102, 7) 4.448,5 5.167,5.25 0.719,0.25 8 false 10 (102, 7) 1.688,5.146 2.406,5.396 0.719,0.25 8 false 10 (102, 7) 2.448,3.875 3.167,4.125 0.719,0.25 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

4 STRAIGHT SCREW PLUG - (Click here) - -
5 ENGINE BALANCER ASSEMBLY 13620B - - -
6 NO. 1 OIL PAN BAFFLE PLATE 12121 - - -
7 STIFFENING CRANKCASE ASSEMBLY 11420 (Click here) - -
8 ENGINE OIL LEVEL SENSOR 89491 (Click here) - -
9 OIL STRAINER SUB-ASSEMBLY 15104 (Click here) - -
10 OIL PAN SUB-ASSEMBLY 12101 (Click here) - -
11 OIL PAN DRAIN PLUG 12101A - - -
12 OIL FILTER UNION 15600A (Click here) - -
13 OIL FILTER SUB-ASSEMBLY 15601 (Click here) - -
14 REAR ENGINE OIL SEAL 11401L (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

MP grease
V100136

Adhesive 1344 - -

A461216N02
1.917,0.583 2.25,0.75 0.333,0.167 1.875,0.542 2.292,0.792 0.417,0.25 3.667,0.583 4,0.75 0.333,0.167 3.625,0.542 4.042,0.792 0.417,0.25 3.938,3.667 4.5,3.667 false 4.49,2.583 5.083,2.583 false 3.469,4.75 4,4.75 false 4.938,1.063 5.625,1.625 5.625,1.625 5.792,1.625 false 5.135,0.927 5.813,0.927 false 5.167,0.667 5.625,0.385 5.625,0.385 5.792,0.385 false 2.25,0.667 2.792,0.667 false 3.25,0.667 3.667,0.667 false 4.042,4.625 4.594,4.979 0.552,0.354 18 false 15 5.031,3.531 5.583,3.885 0.552,0.354 18 false 16 5.448,2.469 6,2.823 0.552,0.354 18 false 17 6.188,0.802 6.74,1.156 0.552,0.354 18 false 18 6.188,1.469 6.74,1.823 0.552,0.354 18 false 19 6.188,0.26 6.74,0.615 0.552,0.354 18 false 20 4.875,3.615 5.427,3.969 0.552,0.354 10 false ● 1.979,0.583 2.438,0.781 0.458,0.198 10 false *T1 3.708,0.583 4.167,0.781 0.458,0.198 10 false *T1 2.833,0.813 3.146,1.01 0.313,0.198 10 false x4 5.271,0.635 5.583,0.833 0.313,0.198 10 false x12 3.271,0.844 3.583,1.042 0.313,0.198 10 false x4 5.177,0.958 5.49,1.156 0.313,0.198 10 false x12 4.854,1.156 5.167,1.354 0.313,0.198 10 false x12

Procedure Part Name Code
Z101186

Z101188

Z101187

15 CYLINDER BLOCK WATER JACKET SPACER 11445 - - -
16 CYLINDER HEAD GASKET 11115 (Click here) - -
17 CYLINDER HEAD SUB-ASSEMBLY 11101 (Click here) - -
18 VALVE STEM CAP 13716 (Click here) - -
19 VALVE LASH ADJUSTER ASSEMBLY 13750 (Click here) - -
20 NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY 13801 (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
*T1 1st: 50 (510, 37)
2nd: Turn 90°
3rd: Turn 90°
- -

A478293N01
3.583,2.917 4.417,3.083 0.833,0.167 5.833,0.083 6.458,0.25 0.625,0.167 3.521,1.896 4.24,2.063 0.719,0.167 0.74,4.479 1.469,4.646 0.729,0.167 3.917,0.031 4.594,0.198 0.677,0.167 5.833,2.583 6.583,2.75 0.75,0.167 0.042,0.573 0.75,0.74 0.708,0.167 0.021,2.833 0.688,3 0.667,0.167 1.865,2.896 2.563,3.063 0.698,0.167 2.531,1.813 3.167,1.979 0.635,0.167 3.25,0.448 3.854,0.615 0.604,0.167 0.104,1.333 0.781,1.5 0.677,0.167 2.583,0.354 3.885,0.74 1.302,0.385 2.635,0.854 3.063,1.521 0.427,0.667 3.917,2.917 3.917,2.75 3.917,2.75 4.583,1.917 false 6.438,0.667 6.604,0.667 6.604,0.667 6.667,0.813 false 3.135,2.083 3.354,1.979 3.354,1.979 3.521,1.979 false 1.094,4.479 1.094,4.313 1.094,4.313 1.99,3.979 false 2.01,4.802 2.01,4.635 2.01,4.635 2.552,4.344 false 6.469,0.156 6.635,0.156 6.635,0.156 6.813,0.438 false 5.083,2.198 5.667,2.667 5.667,2.667 5.833,2.667 false 4.604,0.104 4.771,0.104 4.771,0.104 5.333,0.344 false 5.969,1.979 6.198,1.896 6.198,1.896 6.365,1.896 false 5.625,2.208 6.198,2.333 6.198,2.333 6.365,2.333 false 4.698,1.448 6.115,1.448 false 5.083,1.448 5.083,1 false 5.417,1.448 5.417,1.167 false 5.75,1.448 5.75,1.333 false 6,3.021 6.24,3.021 false 3.26,1.406 3.646,0.854 3.646,0.854 3.813,0.854 false 1.76,0.99 1.833,1.073 1.833,1.073 2,1.073 false 0.75,0.667 0.917,0.667 0.917,0.667 1,0.479 false 0.75,3.833 0.75,3.385 false 2.177,1.917 2.313,1.917 false 1.625,3.604 1.792,3.604 1.792,3.604 2.01,3.313 false 1.177,2.667 1.417,2.667 false 0.25,2.833 0.25,2.333 false 1.854,2.417 2.25,2.729 2.25,2.729 2.25,2.896 false 2.917,0.615 3.073,0.521 3.073,0.521 3.24,0.521 false 0.448,1.323 0.448,0.917 false 3.073,5.063 3.073,4.896 3.073,4.896 3.656,4.031 false 2.802,1.813 2.802,1.125 false 2.813,1.656 2.927,1.656 2.927,1.656 2.927,1.406 false 3.688,5.385 3.688,4.406 false 0.271,0.167 0.688,0.167 false 1.042,1.854 1.042,1.448 false 3.615,2.927 4.479,3.104 0.865,0.177 8 false 28.5 (291, 21) 6.115,0.552 6.667,0.906 0.552,0.354 18 false 25 5.854,0.083 6.583,0.302 0.729,0.219 8 false 10 (102, 7) 3.802,5.469 4.354,5.823 0.552,0.354 18 false 26 3.552,1.896 4.281,2.115 0.729,0.219 8 false 27 (275, 20) 0.781,4.479 1.51,4.698 0.729,0.219 8 false 27 (275, 20) 2.031,4.823 2.583,5.177 0.552,0.354 18 false 28 2.167,3.896 2.781,4.125 0.615,0.229 10 false x12 3.271,2.042 3.885,2.271 0.615,0.229 10 false x8 5.385,0.438 6,0.667 0.615,0.229 10 false x7 3.927,0.031 4.656,0.25 0.729,0.219 8 false 16 (163, 12) 5.854,2.583 6.771,2.771 0.917,0.188 8 false 28.5 (291, 21) 5.052,2.323 5.667,2.552 0.615,0.229 10 false x2 4.646,1.958 5.26,2.188 0.615,0.229 10 false x12 6.729,1.771 7.073,2.135 0.344,0.365 18 false 21 6.74,2.188 7.083,2.552 0.344,0.365 18 false 22 4.385,1.281 4.729,1.646 0.344,0.365 18 false 23 6.625,2.885 6.969,3.25 0.344,0.365 18 false 24 2.323,0.906 2.875,1.26 0.552,0.354 18 false 29 0.063,0.573 0.792,0.792 0.729,0.219 8 false 19 (194, 14) 0.74,0.052 1.292,0.406 0.552,0.354 18 false 30 0.667,3.813 1.219,4.167 0.552,0.354 18 false 31 1.906,1.771 2.458,2.125 0.552,0.354 18 false 32 4.135,0.719 4.688,1.073 0.552,0.354 18 false 33 1.313,3.49 1.865,3.844 0.552,0.354 18 false 34 0.865,2.563 1.417,2.917 0.552,0.354 18 false 35 0.948,1.927 1.5,2.281 0.552,0.354 18 false 36 0.042,2.833 0.927,3.073 0.885,0.24 8 false 24 (245, 18) 0.417,2.25 1.031,2.479 0.615,0.229 10 false x2 1.073,0.354 1.688,0.583 0.615,0.229 10 false x3 1.906,2.896 2.656,3.073 0.75,0.177 8 false 24 (245, 18) 2.542,1.813 3.271,2.031 0.729,0.219 8 false 10 (102, 7) 3.26,0.448 3.99,0.667 0.729,0.219 8 false 10 (102, 7) 0.115,1.333 1,1.552 0.885,0.219 8 false 95 (969, 70) 6.875,0.469 7.125,0.708 0.25,0.24 10 false x2 3.115,5.094 3.667,5.448 0.552,0.354 18 false 27 2.615,0.365 3.229,0.594 0.615,0.229 12 false *B 2.646,0.854 3.26,1.083 0.615,0.229 12 false *A 3.052,0.552 3.667,0.781 0.615,0.229 10 false x2 3.75,4.365 4.365,4.594 0.615,0.229 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

21 EXHAUST CAMSHAFT SUB-ASSEMBLY 13502B (Click here) - -
22 INTAKE CAMSHAFT SUB-ASSEMBLY 13501A (Click here) - -
23 CAMSHAFT BEARING CAP - (Click here) - -
24 CAMSHAFT HOUSING SUB-ASSEMBLY 11103 (Click here) - -
25 FUEL PUMP LIFTER GUIDE 23477 (Click here) - -
26 CRANKSHAFT TIMING GEAR KEY 13471A (Click here) - -
27 BALANCESHAFT DRIVE GEAR 13631 (Click here) - -
28 TIMING CHAIN COVER ASSEMBLY 11310 (Click here) - -
29 CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY 13070A (Click here) - -
30 SET NO. 1 CYLINDER TO TDC (COMPRESSION) - (Click here) - -
31 NO. 1 CHAIN VIBRATION DAMPER 13561 - - -
32 CHAIN TENSIONER SLIPPER 13559 - - -
33 NO. 1 CHAIN TENSIONER ASSEMBLY 13540 (Click here) - -
34 CRANKSHAFT TIMING GEAR OR SPROCKET 13521 - - -
35 CHAIN SUB-ASSEMBLY 13506 - - -
36 CAMSHAFT TIMING GEAR ASSEMBLY 13050 (Click here) - -

*A w/ Stud Bolt *B w/o Stud Bolt
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

A461213N02
6.51,4.417 7.125,4.583 0.615,0.167 2.833,0.917 3.833,1.083 1,0.167 1.083,0.5 1.833,0.667 0.75,0.167 6.083,0.583 7.083,0.75 1,0.167 0.052,1.833 0.75,2 0.698,0.167 0.052,3.021 0.927,3.188 0.875,0.167 6.042,0.542 7.125,0.792 1.083,0.25 4,0.063 5,0.229 1,0.167 3.958,0.021 5.042,0.271 1.083,0.25 3.5,0.333 4.5,0.5 1,0.167 6.458,5.333 7.073,5.5 0.615,0.167 1.042,0.458 1.875,0.708 0.833,0.25 0.01,2.979 0.969,3.229 0.958,0.25 4.333,0.688 4.594,0.688 false 6.167,5.063 6.167,4.729 false 2.479,1.635 2.75,1.25 2.75,1.25 2.917,1.25 false 1.333,4.083 1.333,3.917 1.333,3.917 1.531,3.052 false 1.229,1.375 1.75,1 1.75,1 1.917,1 false 0.583,1 0.917,0.583 0.917,0.583 1.083,0.583 false 5.979,4 6.167,3.667 6.167,3.667 6.333,3.667 false 5.604,1.802 5.854,1.458 5.854,1.458 6.021,1.458 false 6.417,4.333 6.417,4.5 6.417,4.5 6.5,4.5 false 6.75,5.333 6.75,5.167 6.75,5.167 6.563,4.771 false 3.833,1 4.104,1 false 4.5,0.417 4.667,0.417 4.667,0.417 4.938,0.813 false 5,0.135 5.229,0.135 false 5.583,0.667 5.75,0.667 false 0.75,1.917 0.917,1.917 0.917,1.917 1.417,2.167 false 0.5,3.021 0.5,2.396 false 5.021,2.208 5.333,2.5 5.333,2.5 5.5,2.5 false 5.51,2.792 5.865,2.792 false 4.083,1.833 4.25,1.833 4.25,1.833 4.563,2.083 false 5.635,3.885 5.865,3.448 5.865,3.448 6.031,3.448 false 5.854,4.75 5.854,4.5 false 2.719,4.51 2.719,4.26 false 3.229,4.458 3.229,4.208 false 2.073,4.531 2.073,4.365 2.073,4.365 3.073,3.896 false 5.573,1 5.875,1 false 5.177,0.615 5.615,0.375 5.615,0.375 5.781,0.375 false 6.594,0.188 6.844,0.188 false 1.083,3.354 1.083,2.938 false 6.281,0.073 6.896,0.448 0.615,0.375 18 false 37 3.281,1.135 3.813,1.469 0.531,0.333 18 false 39 1.5,4.094 2.021,4.406 0.521,0.313 18 false 40 2.292,0.844 2.802,1.177 0.51,0.333 18 false 41 4.01,0.542 4.458,0.875 0.448,0.333 18 false 42 6.375,1.333 6.844,1.729 0.469,0.396 18 false 44 6.677,3.552 7.125,3.927 0.448,0.375 18 false 45 6.208,5.042 6.698,5.396 0.49,0.354 18 false 46 0.948,3.406 1.604,3.719 0.656,0.313 18 false 47 0.802,0.99 1.115,1.188 0.313,0.198 10 false x3 6.521,4.417 7.156,4.583 0.635,0.167 8 false 10 (102, 7) 1.125,0.5 2.031,0.719 0.906,0.219 8 false 43 (438, 32) 6.104,0.594 7.094,0.76 0.99,0.167 8 false 7.5 (76, 66 in.*lbf) 0.083,1.833 1.083,2 1,0.167 8 false 24 (245, 18) 0.073,3.021 1.073,3.167 1,0.146 8 false 260 (2651, 192) 4.75,1 5.063,1.198 0.313,0.198 10 false x2 4.24,0.938 4.552,1.135 0.313,0.198 10 false x11 5.094,2.115 5.406,2.313 0.313,0.198 10 false x4 3.833,0.615 4.115,0.969 0.281,0.354 10 false ● 5.583,2.427 5.917,2.844 0.333,0.417 10 false ● 3.917,1.771 4.198,2.125 0.281,0.354 10 false ● 5.938,2.74 6.219,3.094 0.281,0.354 10 false ● 2.667,4.563 2.948,4.917 0.281,0.354 10 false ● 3.177,4.521 3.458,4.875 0.281,0.354 10 false ● 6.146,3.385 6.427,3.74 0.281,0.354 10 false ● 5.802,4.792 6.083,5.146 0.281,0.354 10 false ● 1.333,4.156 1.615,4.51 0.281,0.354 10 false ● 6.656,4.656 6.969,4.854 0.313,0.198 10 false x2 6.531,4.188 6.844,4.385 0.313,0.198 10 false x2 1.604,2.156 1.917,2.354 0.313,0.198 10 false x17 1.948,4.563 2.51,4.906 0.563,0.344 18 false 38 5.854,0.26 6.396,0.594 0.542,0.333 18 false 43 5.917,0.885 6.552,1.146 0.635,0.26 18 false 43 4.646,0.781 4.958,0.979 0.313,0.198 10 false x3 5.802,0.583 6.177,0.833 0.375,0.25 10 false ●★ 3.688,0.042 4.042,0.281 0.354,0.24 10 false ●★ 4.031,0.063 5.083,0.25 1.052,0.188 8 false 7.5 (76, 66 in.*lbf) 3.531,0.333 4.521,0.5 0.99,0.167 8 false 7.5 (76, 66 in.*lbf) 6.469,5.333 7.156,5.5 0.688,0.167 8 false 10 (102, 7) 2.865,0.917 3.917,1.167 1.052,0.25 8 false 7.5 (76, 66 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

37 SET NO. 1 CYLINDER TO TDC (COMPRESSION) - (Click here) - -
38 OIL PUMP DRIVE GEAR 13519 - - -
39 NO. 2 TIMING CHAIN COVER ASSEMBLY 11320B (Click here) - -
40 TIMING CHAIN COVER OIL SEAL 11301C (Click here) - -
41 ENGINE MOUNTING BRACKET RH 12315A (Click here) - -
42 SPARK PLUG TUBE GASKET 11193 (Click here) - -
43 CAMSHAFT POSITION SENSOR 11102A - - -
44 CYLINDER HEAD COVER SUB-ASSEMBLY 11201 (Click here) - -
45 OUTLET WATER BY-PASS SUB-ASSEMBLY 16305E (Click here) - -
46 OUTLET WATER SUB-ASSEMBLY 16304 (Click here) - -
47 CRANKSHAFT PULLEY ASSEMBLY 13470 (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part ★ Precoated part

A478873N01
2.073,2.635 2.833,2.802 0.76,0.167 2.75,0.417 3.417,0.583 0.667,0.167 5.333,0.583 6.083,0.75 0.75,0.167 5.083,2.063 5.75,2.229 0.667,0.167 0.365,0.771 1.031,0.938 0.667,0.167 1.115,2.292 1.781,2.458 0.667,0.167 0.25,4.531 0.917,4.698 0.667,0.167 6.385,4.646 7.052,4.813 0.667,0.167 6.344,4.604 7.094,4.854 0.75,0.25 1.583,5.083 2.25,5.25 0.667,0.167 1.542,5.042 2.292,5.292 0.75,0.25 6.698,4.646 6.698,4.479 6.698,4.479 6.448,3.99 false 1.667,2.854 1.896,2.708 1.896,2.708 2.063,2.708 false 0.698,3.385 0.865,3.385 0.865,3.385 1.521,3.25 false 6.031,4.302 6.031,3.938 false 2.469,2.51 2.802,2.51 false 2.688,5.115 2.688,4.771 false 1.917,5.083 1.917,4.917 1.917,4.917 2.333,4.604 false 3.479,2.052 3.719,2.052 false 3.51,1.74 3.75,1.74 false 0.792,2.729 0.948,2.375 0.948,2.375 1.115,2.375 false 0.698,3.094 0.938,3.094 false 1.958,1.417 2.167,0.5 2.167,0.5 2.333,0.5 false 1.031,0.854 1.198,0.854 1.198,0.854 1.521,1.396 false 2.604,1.635 3.042,0.927 3.042,0.927 3.208,0.927 false 1.719,1.771 1.99,1.771 false 5.75,2.146 5.917,2.146 5.917,2.146 6,3.188 false 1.625,4.552 1.625,4.385 1.625,4.385 1.99,4.167 false 5.073,4.125 5.073,3.958 5.073,3.958 5.448,3.573 false 0.573,4.531 0.573,4.365 0.573,4.365 1.344,4.135 false 4.313,0.667 5.333,0.667 false 1.594,3.604 1.854,3.604 false 2.646,3.802 2.813,3.802 2.813,3.802 2.938,3.51 false 6.073,4.333 6.406,4.656 0.333,0.323 18 false 48 2.104,2.302 2.438,2.625 0.333,0.323 18 false 49 2.792,5.156 3.125,5.479 0.333,0.323 18 false 50 3.198,1.927 3.531,2.25 0.333,0.323 18 false 51 3.198,1.594 3.531,1.917 0.333,0.323 18 false 52 1.25,3.49 1.583,3.813 0.333,0.323 18 false 53 0.417,2.979 0.75,3.302 0.333,0.323 18 false 54 3.573,0.823 3.906,1.146 0.333,0.323 18 false 55 1.396,1.667 1.729,1.99 0.333,0.323 18 false 56 4.74,2.01 5.073,2.333 0.333,0.323 18 false 57 2.135,2.646 3.052,2.844 0.917,0.198 8 false 43 (438, 32) 1.771,2.917 2.094,3.094 0.323,0.177 10 false x4 0.917,2.688 1.24,2.865 0.323,0.177 10 false x2 0.51,3.323 0.667,3.521 0.156,0.198 10 false ● 2.781,0.417 3.51,0.667 0.729,0.25 8 false 10 (102, 7) 4.573,2.063 4.729,2.26 0.156,0.198 10 false ★ 1.635,4.573 1.969,4.896 0.333,0.323 18 false 58 5.021,4.156 5.177,4.354 0.156,0.198 10 false ● 5.385,0.594 6.208,0.802 0.823,0.208 8 false 20 (204, 15) 6.5,0.51 6.833,0.833 0.333,0.323 18 false 59 1.656,1.344 1.979,1.521 0.323,0.177 10 false x2 2.083,1.365 2.406,1.542 0.323,0.177 10 false x2 4.323,0.719 4.646,0.896 0.323,0.177 10 false x3 6.542,3.896 6.865,4.073 0.323,0.177 10 false x3 2.448,3.75 2.604,3.948 0.156,0.198 10 false ● 0.042,0.76 0.708,0.917 0.667,0.156 10 false ● ★ 2.385,0.427 3.052,0.583 0.667,0.156 10 false ● ★ 5.104,2.063 5.833,2.313 0.729,0.25 8 false 10 (102, 7) 0.396,0.771 1.125,1.021 0.729,0.25 8 false 10 (102, 7) 1.146,2.292 1.875,2.542 0.729,0.25 8 false 10 (102, 7) 0.292,4.531 1.021,4.781 0.729,0.25 8 false 10 (102, 7) 6.427,4.646 7.156,4.896 0.729,0.25 8 false 10 (102, 7) 1.625,5.083 2.354,5.333 0.729,0.25 8 false 10 (102, 7)

Procedure Part Name Code
Z101186

Z101188

Z101187

48 VACUUM PUMP ASSEMBLY 29300 (Click here) - -
49 PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY) 12204C - - -
50 CRANKSHAFT POSITION SENSOR 11401G (Click here) - -
51 OIL FILLER CAP GASKET 12108A - - -
52 OIL FILLER CAP ASSEMBLY 12180E - - -
53 ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING) 16032 (Click here) - -
54 WATER INLET WITH THERMOSTAT SUB-ASSEMBLY 16031 (Click here) - -
55 CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side) 15370 (Click here) - -
56 CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side) 15370 (Click here) - -
57 OIL PRESSURE AND TEMPERATURE SENSOR 89448D (Click here) - -
58 KNOCK SENSOR 89615 (Click here) - -
59 SPARK PLUG 19100P (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

Adhesive 1344
★ Precoated part - -

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN

Z101186

NOTICE:

If the straight pin is deformed or damaged, replace it.



a.
A461045C01
5.427,0.75 5.74,0.948 0.313,0.198 10 false *a 0.479,0.083 0.938,0.49 0.458,0.406 18 false i
*a Protrusion Height - -


i.

Using a plastic hammer, tap in 2 new straight pins to the No. 2 timing chain cover assembly.

Standard Protrusion Height:

5.0 to 7.0 mm (0.197 to 0.276 in.)




Hide 2.INSTALL RING PIN

Z101186

NOTICE:

If the ring pin is deformed or damaged, replace it.



a.
A460995C01
5.563,0.74 5.875,0.938 0.313,0.198 10 false *a 5.49,2.74 5.802,2.938 0.313,0.198 10 false *a 1.583,0.083 2,0.438 0.417,0.354 18 false i 1.594,2.094 2.01,2.448 0.417,0.354 18 false ii
*a Protrusion Height - -


i.

Using a plastic hammer, tap in 6 new ring pins to the stiffening crankcase assembly.

Standard Protrusion Height:

3.5 to 4.5 mm (0.138 to 0.177 in.)



ii.

Using a plastic hammer, tap in 8 new ring pins to the camshaft housing sub-assembly.

Standard Protrusion Height:

3.2 to 4.3 mm (0.126 to 0.169 in.)




Hide 3.INSTALL STUD BOLT

Z101186

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.



a.
A460992C01
0.833,4.635 1.146,4.833 0.313,0.198 10 false *a 0.833,4.906 1.146,5.104 0.313,0.198 10 false *b 1.458,4.729 1.771,4.927 0.313,0.198 10 false *c 2.594,4.583 2.906,4.781 0.313,0.198 10 false *d 2.646,4.938 2.958,5.135 0.313,0.198 10 false *e 3.458,4.771 3.771,4.969 0.313,0.198 10 false *f 4.406,4.635 4.719,4.833 0.313,0.198 10 false *e 4.417,4.896 4.729,5.094 0.313,0.198 10 false *e 4.938,4.771 5.25,4.969 0.313,0.198 10 false *g 0.604,0.146 1.01,0.469 0.406,0.323 18 false i 4.083,0.198 4.49,0.521 0.406,0.323 18 false ii 0.625,2.031 1.031,2.354 0.406,0.323 18 false iii 4.094,2.063 4.5,2.385 0.406,0.323 18 false iv 2.031,0.927 2.188,1.125 0.156,0.198 10 true A 5.083,0.771 5.24,0.969 0.156,0.198 10 true B 1.583,3.417 1.74,3.615 0.156,0.198 10 true C 2.74,3.5 2.896,3.698 0.156,0.198 10 true C 6.302,3.146 6.458,3.344 0.156,0.198 10 true D 0.469,4.125 0.625,4.323 0.156,0.198 10 true A 2.156,4.094 2.313,4.292 0.156,0.198 10 true B 3.948,4.083 4.104,4.281 0.156,0.198 9 true C 5.5,3.813 5.656,4.01 0.156,0.198 10 true D 6.208,4.281 6.521,4.479 0.313,0.198 10 false *h 6.208,5.146 6.521,5.344 0.313,0.198 10 false *i 6.656,4.688 6.969,4.885 0.313,0.198 10 false *j 4.708,0.271 5.083,0.51 0.375,0.24 12 false *A
*A w/ Stud Bolt - -
*a 14 mm (0.551 in.) *b 13 mm (0.512 in.)
*c 29 mm (1.142 in.) *d 21 mm (0.827 in.)
*e 9 mm (0.354 in.) *f 34 mm (1.339 in.)
*g 19 mm (0.748 in.) *h 33.1 mm (1.303 in.)
*i 15 mm (0.591 in.) *j 95 mm (3.740 in.)


i.

Using an E8 "TORX" socket wrench, install the stud bolt to the cylinder head sub-assembly.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


ii.

Using an E6 "TORX" socket wrench, install the stud bolt to the timing chain cover assembly.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


iii.

Using an E6 "TORX" socket wrench, install the 2 stud bolts to the stiffening crankcase assembly

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


iv.

Using an E8 "TORX" socket wrench, install the stud bolt to the timing chain cover assembly.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 4.INSTALL STRAIGHT SCREW PLUG

a.
A459774N01
0.479,0.104 0.76,0.458 0.281,0.354 18 false i

i.

Using a 10 mm hexagon socket wrench, install the straight screw plug to the stiffening crankcase assembly.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 13620B 5.INSTALL ENGINE BALANCER ASSEMBLY

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

Hide 12121 6.INSTALL NO. 1 OIL PAN BAFFLE PLATE

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 11420 7.INSTALL STIFFENING CRANKCASE ASSEMBLY

Z101186

NOTICE:

Remove any oil from the contact surfaces.



a.
A459992C01
2.667,1.385 3.083,1.385 false 0.729,0.104 1.01,0.458 0.281,0.354 18 false i 2.573,1.99 2.854,2.344 0.281,0.354 18 false iii 4.135,0.125 4.417,0.479 0.281,0.354 18 false ii 3.125,1.313 3.406,1.667 0.281,0.354 10 false *a 4.688,1.656 4.865,1.844 0.177,0.188 10 true A 5.115,1.688 5.292,1.896 0.177,0.208 10 false B 4.688,0.031 4.969,0.385 0.281,0.354 10 false C 5.771,0.146 5.948,0.354 0.177,0.208 10 false B 5.792,1.667 5.969,1.875 0.177,0.208 10 false B 5.073,0.063 5.354,0.417 0.281,0.354 10 false C 5.438,0.073 5.719,0.427 0.281,0.354 10 false C 5.427,1.698 5.708,2.052 0.281,0.354 10 false C 3.385,1.99 3.563,2.177 0.177,0.188 10 true 1 3.729,3.615 3.906,3.802 0.177,0.188 10 false 2 3.76,2.01 3.938,2.198 0.177,0.188 10 false 3 3.448,3.615 3.625,3.802 0.177,0.188 10 false 4 4.104,2.094 4.281,2.281 0.177,0.188 10 false 5 4.125,3.573 4.302,3.76 0.177,0.188 10 false 6 3.021,1.979 3.198,2.167 0.177,0.188 10 false 7 3.01,3.573 3.188,3.76 0.177,0.188 10 true 8 6.146,0.052 6.427,0.406 0.281,0.354 10 false *b 4.448,2.083 4.729,2.438 0.281,0.354 10 false *c
*a Seal Packing *b Bolt Type
*c Tightening Order - -


i.

Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after the installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).

·

After installation, if the seal packing has seeped out, wipe it off.

·

Do not start the engine for at least 2 hours after installation.




ii.

Temporarily install the stiffening crankcase assembly with the 8 bolts.

Bolt Length :
Item Length
Bolt (A) 170 mm (6.69 in.)
Bolt (B) 120 mm (4.72 in.)
Bolt (C) 40 mm (1.57 in.)



iii.

Tighten the 8 bolts in the order shown in the illustration to install the stiffening crankcase assembly.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 89491 8.INSTALL ENGINE OIL LEVEL SENSOR

Z101186

Click here(Click here)

Hide 15104 9.INSTALL OIL STRAINER SUB-ASSEMBLY

a.
A461031N01
0.979,0.094 1.26,0.448 0.281,0.354 18 false i 6.365,0.938 6.646,1.292 0.281,0.354 18 false ii 3.958,0.063 4.24,0.417 0.281,0.354 18 false iii

i.

Apply a light coat of engine oil to a new oil strainer gasket.


ii.

Install the oil strainer gasket to the oil strainer sub-assembly.


iii.

Using an 8 mm socket wrench, install the oil strainer sub-assembly to the stiffening crankcase assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 12101 10.INSTALL OIL PAN SUB-ASSEMBLY

Z101186

NOTICE:

Remove any oil from the contact surfaces.



a.
A461042C01
2.927,1.083 3.344,1.083 false 3.948,3.323 3.625,2.979 true 3.26,3.208 3.615,2.969 true 2.24,0.5 2.396,0.698 0.156,0.198 10 true A 2.229,0.813 2.385,1.01 0.156,0.198 10 true A 5.042,0.167 5.479,0.365 0.438,0.198 10 false A - A 4.667,0.479 4.875,0.698 0.208,0.219 10 false *b 4.667,0.719 4.875,0.938 0.208,0.219 10 false *c 0.677,0.208 0.99,0.563 0.313,0.354 18 false i 2.417,2.021 2.729,2.375 0.313,0.354 18 false ii 3.521,2.74 3.729,2.958 0.208,0.219 10 true *d 3.406,1 3.615,1.219 0.208,0.219 10 false *a 3.875,3.583 4.177,3.781 0.302,0.198 10 false 1, 7 3.323,1.969 3.719,2.167 0.396,0.198 10 false 2, 13 3.896,1.979 4.198,2.177 0.302,0.198 10 false 3 4.354,2.135 4.656,2.333 0.302,0.198 10 false 4 4.375,2.844 4.677,3.042 0.302,0.198 10 true 5 4.375,3.094 4.677,3.292 0.302,0.198 10 true 6 3.646,3.49 3.813,3.677 0.167,0.188 10 true 8 3.219,3.479 3.385,3.667 0.167,0.188 10 true 9 2.656,3.281 2.823,3.469 0.167,0.188 10 true 10 2.708,2.333 2.875,2.521 0.167,0.188 10 true 11 3.083,2.26 3.25,2.448 0.167,0.188 10 true 12
*a Seal Packing *b 4.5 mm (0.177 in.)
*c 2.5 to 3.5 mm (0.0984 to 0.138 in.) *d Nut


i.

Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after the installation.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/0.0787 in.).




ii.

Install the oil pan sub-assembly with the 9 bolts and 2 nuts in several steps in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 12101A 11.INSTALL OIL PAN DRAIN PLUG

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

Hide 15600A 12.INSTALL OIL FILTER UNION

a.
A459978N01
0.458,0.083 0.74,0.438 0.281,0.354 18 false i

i.

Using a 12 mm hexagon socket wrench, install the oil filter union to the stiffening crankcase assembly.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)



Hide 15601 13.INSTALL OIL FILTER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 11401L 14.INSTALL REAR ENGINE OIL SEAL

Z101186

Click here(Click here)

Hide 11445 15.INSTALL CYLINDER BLOCK WATER JACKET SPACER

Hide 11115 16.INSTALL CYLINDER HEAD GASKET

Z101186

Click here(Click here)

Hide 11101 17.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

The cylinder head set bolts are tightened in 3 progressive steps.

·

Perform inspection after repair after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



a.
A461569C01
5.292,4.698 4.771,5.177 4.771,5.177 4.698,4.698 true 0.573,0.406 0.854,0.76 0.281,0.354 18 false i 3.563,0.104 3.844,0.458 0.281,0.354 18 false ii 3.573,1.302 3.854,1.656 0.281,0.354 18 false iii 0.573,2.854 0.854,3.208 0.281,0.354 18 false iv 4.375,4.979 4.656,5.333 0.281,0.354 18 false v 4.417,3.729 4.698,4.083 0.281,0.354 18 false vi 5.74,4.917 6.021,5.271 0.281,0.354 18 false vii 3.948,3.083 4.083,3.26 0.135,0.177 10 false A 3.948,2.094 4.083,2.271 0.135,0.177 10 false A 5.708,3.073 5.844,3.25 0.135,0.177 10 true A 5.719,2.104 5.854,2.281 0.135,0.177 10 true A 4.615,3.167 4.75,3.344 0.135,0.177 10 true B 4.583,1.948 4.719,2.125 0.135,0.177 10 true B 4.99,1.948 5.125,2.125 0.135,0.177 10 true B 5.01,3.135 5.146,3.313 0.135,0.177 10 true B 1.552,4.792 1.688,4.969 0.135,0.177 10 true 1 1.958,3.563 2.094,3.74 0.135,0.177 10 true 2 1.958,4.781 2.094,4.958 0.135,0.177 10 true 3 1.531,3.552 1.667,3.729 0.135,0.177 10 true 4 2.594,4.677 2.729,4.854 0.135,0.177 10 true 5 0.906,3.698 1.042,3.875 0.135,0.177 10 false 6 0.927,4.688 1.063,4.865 0.135,0.177 10 false 7 2.625,3.688 2.76,3.865 0.135,0.177 10 true 8 4.302,4.094 4.625,4.25 0.323,0.156 10 false 90° 5.49,4.052 5.885,4.292 0.396,0.24 10 false 90° 4.698,5.219 4.979,5.385 0.281,0.167 10 false *a
*a Paint Mark - -
V100136

Front of Engine - -


i.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Ensure that the contact surface of the cylinder head sub-assembly is free of oil.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.




ii.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


iii.

Install the 8 plate washers to the 8 cylinder head set bolts.

NOTICE:

Be careful not to drop the plate washers into the cylinder head sub-assembly.


HINT:
Item Length
Bolt (A) 129.1 to 130.9 mm (5.08 to 5.15 in.)
Bolt (B) 139.1 to 140.9 mm (5.48 to 5.55 in.)



iv.

Step 1:

1. Using a 12 mm socket wrench, install and uniformly tighten the 8 cylinder head set bolts in several steps in the order shown in the illustration.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


v.

Mark each cylinder head set bolt head with paint as shown in the illustration.


vi.

Step 2:

1. Tighten the cylinder head set bolts 90° in the order shown in step 1.


vii.

Step 3:

1. Tighten the cylinder head set bolts another 90° in the order shown in step 1.

2. Check that the paint marks are now facing rearward.



Hide 13716 18.INSTALL VALVE STEM CAP

a.
A461012N01
0.5,0.073 1.302,0.375 0.802,0.302 18 false i 3.854,0.063 4.656,0.365 0.802,0.302 18 false ii

i.

Apply a light coat of engine oil to the valve stem cap ends.


ii.

Install the 12 valve stem caps to the cylinder head sub-assembly.

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Do not drop the valve stem caps into the cylinder head sub-assembly.





Hide 13750 19.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.
A461011N01
0.5,0.229 1.875,0.583 1.375,0.354 18 false i 2.354,3.094 3.729,3.448 1.375,0.354 18 false ii

i.

Inspect the 12 valve lash adjuster assemblies before installing them.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


ii.

Install the 12 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.




Hide 13801 20.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A461007C01
4.25,0.708 4.75,0.708 false 2.521,0.625 3.021,0.625 false 3.75,0.354 3.99,0.167 3.99,0.167 4.167,0.167 false 4.208,0.083 4.521,0.281 0.313,0.198 10 false *1 4.813,0.656 5.125,0.854 0.313,0.198 10 false *2 2.333,0.552 2.646,0.75 0.313,0.198 10 false *3 0.458,0.021 0.813,0.354 0.354,0.333 18 false i
*1 No. 1 Valve Rocker Arm Sub-assembly *2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap - -


i.

Install the 12 No. 1 valve rocker arm sub-assemblies as shown in the illustration.

NOTICE:
·

Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.

·

Install the same parts in the same combination to their original locations.





Hide 13502B 21.INSTALL EXHAUST CAMSHAFT SUB-ASSEMBLY

Z101186

HINT:

Perform inspection after repair after replacing the exhaust camshaft sub-assembly.

Click here(Click here)



a.
A461013N01
0.5,0.094 1.875,0.448 1.375,0.354 18 false i 4.531,0.052 5.906,0.406 1.375,0.354 18 false ii

i.

Clean the camshaft journals and camshaft housing sub-assembly.


ii.

Install the exhaust camshaft sub-assembly to the camshaft housing sub-assembly.

NOTICE:

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.




Hide 13501A 22.INSTALL INTAKE CAMSHAFT SUB-ASSEMBLY

Z101186

HINT:

Perform inspection after repair after replacing the intake camshaft sub-assembly.

Click here(Click here)



a.
A461014N01
0.479,0.063 1.854,0.417 1.375,0.354 18 false i 4.719,0.073 6.094,0.427 1.375,0.354 18 false ii

i.

Clean the camshaft journals and camshaft housing sub-assembly.


ii.

Install the intake camshaft sub-assembly to the camshaft housing sub-assembly.

NOTICE:

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.




Hide 23.INSTALL CAMSHAFT BEARING CAP

a.
A459985C01
1.667,1.448 1.625,1.208 true 2.125,1.458 2.083,1.219 true 1.604,1.479 1.823,1.677 0.219,0.198 10 true *a 2.01,1.49 2.229,1.688 0.219,0.198 10 true *b 5.188,1.135 5.323,1.333 0.135,0.198 10 true 1 5.146,0.375 5.281,0.573 0.135,0.198 10 true 2 4.75,1.125 4.885,1.323 0.135,0.198 10 true 3 5.521,0.583 5.656,0.781 0.135,0.198 10 true 5 4.646,0.469 4.781,0.667 0.135,0.198 10 true 4 5.563,1.396 5.698,1.594 0.135,0.198 10 true 6 4.323,1.125 4.458,1.323 0.135,0.198 10 true 7 0.438,0.146 0.708,0.417 0.271,0.271 18 false i 3.948,0.156 4.219,0.427 0.271,0.271 18 false ii
*a 2 *b 3 to 4


i.

Place the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and No. 3 camshaft bearing caps and No. 4 camshaft bearing cap in their correct locations.


ii.

Uniformly tighten the 7 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)



Hide 11103 24.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Z101186

NOTICE:

Remove any oil from the contact surfaces.



a.
A461054C01
1.438,0.313 1.75,0.167 1.75,0.167 1.917,0.167 false 1.688,0.667 2.021,0.667 false 0.5,0.75 0.667,0.75 0.667,0.75 0.958,0.5 true 1.448,1.75 1.75,1.583 1.75,1.583 1.917,1.583 false 1.729,2.083 2.063,2.083 false 0.542,2.167 0.708,2.167 0.708,2.167 1,1.917 true 3.135,1.104 3.417,0.75 3.417,0.75 3.583,0.75 false 1.958,1.5 2.333,1.667 0.375,0.167 10 false *1 0.302,0.667 0.677,0.833 0.375,0.167 10 false *2 0.552,0.146 0.969,0.396 0.417,0.25 18 false i 2.042,0.583 2.417,0.75 0.375,0.167 10 false *3 1.958,0.083 2.333,0.25 0.375,0.167 10 false *1 2.104,2 2.479,2.167 0.375,0.167 10 false *3 0.333,2.083 0.708,2.25 0.375,0.167 10 false *2 0.875,0.167 1.25,0.333 0.375,0.167 10 false *a 0.917,1.583 1.292,1.75 0.375,0.167 10 false *b 3.667,0.667 4.042,0.833 0.375,0.167 10 false *c 5.313,1.052 5.688,1.219 0.375,0.167 10 false *d 5.74,1.208 5.917,1.365 0.177,0.156 10 true *e 2.26,4.573 2.406,4.729 0.146,0.156 10 true B 1.396,4.573 1.542,4.729 0.146,0.156 10 true A 1.813,4.573 1.958,4.729 0.146,0.156 10 true A 2.99,4.323 3.135,4.479 0.146,0.156 10 true B 2.958,3.698 3.104,3.854 0.146,0.156 10 false B 2.313,3.656 2.458,3.813 0.146,0.156 10 true B 2.125,3.625 2.271,3.781 0.146,0.156 10 true B 1.729,3.583 1.875,3.74 0.146,0.156 10 true B 1.073,3.594 1.219,3.75 0.146,0.156 10 false B 0.958,4.281 1.104,4.438 0.146,0.156 10 true B 1.104,5.021 1.25,5.177 0.146,0.156 10 true B 1.698,5.052 1.844,5.208 0.146,0.156 10 true B 2.125,5.031 2.271,5.188 0.146,0.156 10 true B 2.802,4.979 2.948,5.135 0.146,0.156 10 true B 4.615,4.583 4.76,4.74 0.146,0.156 10 true 1 4.906,5.042 5.052,5.198 0.146,0.156 10 true 2 4.917,3.573 5.063,3.729 0.146,0.156 10 true 3 5.042,4.594 5.188,4.75 0.146,0.156 10 true 4 5.302,5.031 5.448,5.188 0.146,0.156 10 true 5 5.302,3.594 5.448,3.75 0.146,0.156 10 true 6 5.49,4.542 5.635,4.698 0.146,0.156 10 true 7 6,4.948 6.146,5.104 0.146,0.156 10 true 8 5.51,3.604 5.656,3.76 0.146,0.156 10 true 9 6.177,4.302 6.375,4.458 0.198,0.156 10 true 10 6.125,3.635 6.302,3.792 0.177,0.156 10 true 11 4.125,4.271 4.302,4.427 0.177,0.156 10 true 12 2.719,0.333 3.135,0.583 0.417,0.25 18 false ii 5.24,0.698 5.656,0.948 0.417,0.25 18 false iii 1.271,3.156 1.688,3.406 0.417,0.25 18 false iv 4.51,3.135 4.927,3.385 0.417,0.25 18 false v 4.25,4.99 4.427,5.146 0.177,0.156 10 true 13 4.219,3.563 4.396,3.719 0.177,0.156 10 true 14
*1 No. 1 Valve Rocker Arm Sub-assembly *2 Valve Stem Cap
*3 Valve Lash Adjuster Assembly - -
*a Incorrect *b Correct
*c Seal Packing *d 12° to 42°
*e 83° to 113° - -


i.

Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


ii.

Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




iii.

Position the knock pins of the intake camshaft sub-assembly and exhaust camshaft sub-assembly as shown in the illustration.


iv.

Temporarily install the camshaft housing sub-assembly with the 14 bolts.

HINT:
Item Length
Bolt (A) 40 mm (1.57 in.)
Bolt (B) 65 mm (2.56 in.)



v.

Install the camshaft housing sub-assembly, and then tighten the 14 bolts in several steps in the order shown in the illustration.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)

NOTICE:
·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.





Hide 23477 25.INSTALL FUEL PUMP LIFTER GUIDE

a.
A459969N01
0.469,0.083 0.75,0.438 0.281,0.354 18 false i

i.

Using an 8 mm socket wrench, install the fuel pump lifter guide to the No. 4 camshaft bearing cap with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 13471A 26.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A459967N01
0.51,0.063 0.792,0.417 0.281,0.354 18 false i

i.

Using a plastic hammer, tap in the 2 crankshaft timing gear keys.

HINT:

Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.




Hide 13631 27.INSTALL BALANCESHAFT DRIVE GEAR

a.
A461009C01
2.167,2.25 3.563,2.115 true 2.167,2.25 3.531,2.385 true 5.125,1.813 5.406,2.167 0.281,0.354 18 false ii 2.052,0.063 2.333,0.417 0.281,0.354 18 false i 1.969,2.208 2.281,2.406 0.313,0.198 10 false *a
*a Timing Mark - -


i.

Install the balanceshaft drive gear with the crankshaft.


ii.

Check that the timing mark are as shown in the illustration.



Hide 11310 28.INSTALL TIMING CHAIN COVER ASSEMBLY

a.
A458996C01
0.854,0.385 1.167,0.583 0.313,0.198 10 false *a 4.104,0.385 4.417,0.583 0.313,0.198 10 false *b 0.531,0.125 0.927,0.521 0.396,0.396 18 false i
*a Timing Chain Cover Assembly Side *b Engine Assembly Side


i.

Clean the contact surfaces of the timing chain cover assembly, cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.



b.
A458997C01
4.833,1.917 4.396,1.448 true 4.833,1.917 4.25,2.219 true 3.25,1.75 2.583,2 true 3.688,1.885 2.583,2 true 4.906,1.865 5.219,2.063 0.313,0.198 10 false *a 2.375,1.938 2.688,2.135 0.313,0.198 10 false *b 1.802,0.406 2.115,0.604 0.313,0.198 10 false *c 5.531,0.427 5.844,0.625 0.313,0.198 10 false *c 4.302,0.083 4.615,0.281 0.313,0.198 10 false *d 2.229,2.74 2.542,2.938 0.313,0.198 10 false *e 5.104,2.75 5.417,2.948 0.313,0.198 10 false *e 6.469,2.01 6.781,2.208 0.313,0.198 10 false *f 0.531,1.979 0.844,2.177 0.313,0.198 10 false *f 2.188,4.146 2.5,4.344 0.313,0.198 10 false *g 1.177,4.958 1.49,5.156 0.313,0.198 10 false *h 1.438,3.833 2.135,4.063 0.698,0.229 10 false A - A (★) 3.031,0.646 3.344,0.844 0.313,0.198 10 false ★ 4.563,0.281 4.875,0.479 0.313,0.198 10 false ★ 4.5,0.927 4.677,1.104 0.177,0.177 10 true ★ 4.135,2.896 4.302,3.073 0.167,0.177 10 true ★ 3.198,2.865 3.365,3.021 0.167,0.156 10 true ★ 2.948,3.281 3.104,3.479 0.156,0.198 10 true A 3.25,3.281 3.406,3.479 0.156,0.198 10 true A 0.479,0.094 0.719,0.427 0.24,0.333 18 true i
*a 2.5 to 3.5 mm (0.0984 to 0.138 in.) *b 2.0 to 6.0 mm (0.0787 to 0.236 in.)
*c 10 mm (0.394 in.) *d 30 mm (1.181 in.)
*e 20 mm (0.787 in.) *f 344.2 mm (1.13 ft.)
*g 4.0 to 6.0 mm (0.157 to 0.236 in.) *h 3.0 to 4.0 mm (0.118 to 0.157 in.)
V100155

Seal Packing - -


i.

Apply seal packing in a continuous line to the timing chain cover assembly as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Clean the surfaces with non-residue solvent before applying seal packing.

·

Install the timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not add oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).





c.
A461015N02
1.833,1 1.99,1.198 0.156,0.198 10 true A 2.385,0.729 2.542,0.927 0.156,0.198 10 false B 6.156,1.521 6.313,1.719 0.156,0.198 10 true 1 4.844,1.813 5,2.01 0.156,0.198 10 false 2 4.844,1.813 5,2.01 0.156,0.198 10 false 2 4.844,1.5 5,1.698 0.156,0.198 10 false 3 6.177,1.781 6.333,1.979 0.156,0.198 10 false 4 6.063,1.917 6.219,2.115 0.156,0.198 10 true 5 6.156,2.115 6.313,2.313 0.156,0.198 10 true 6 5.646,2.594 5.802,2.792 0.156,0.198 10 true 7 5.323,2.583 5.458,2.771 0.135,0.188 10 true 8 4.698,2.146 4.854,2.344 0.156,0.198 10 false 9 4.844,1.188 5.104,1.365 0.26,0.177 10 false 10 5.594,1.01 5.813,1.167 0.219,0.156 10 true 11 6.052,1.219 6.365,1.375 0.313,0.156 10 true 12 5.302,0.417 5.521,0.563 0.219,0.146 10 true 14 5.698,0.344 5.927,0.5 0.229,0.156 10 true 13 4.792,0.771 5.167,0.927 0.375,0.156 10 false 15 4.802,0.583 5.063,0.74 0.26,0.156 10 false 16 4.76,0.417 5.052,0.583 0.292,0.167 10 false 17 6.188,0.75 6.438,0.948 0.25,0.198 10 false 18 6.271,0.438 6.51,0.604 0.24,0.167 10 false 19 5.938,0.042 6.219,0.26 0.281,0.219 10 false 20 0.698,0.073 0.979,0.427 0.281,0.354 18 false i 4.625,0.073 4.906,0.427 0.281,0.354 18 false ii 2.479,0.427 2.635,0.625 0.156,0.198 10 false B 2.167,0.021 2.323,0.219 0.156,0.198 10 false B 2,0.375 2.156,0.573 0.156,0.198 10 true B 1.531,0.417 1.688,0.615 0.156,0.198 10 true B 1.063,0.75 1.219,0.948 0.156,0.198 10 false B 1.094,0.583 1.25,0.781 0.156,0.198 10 false B 1.01,0.406 1.167,0.604 0.156,0.198 10 false B 2.25,1.198 2.406,1.396 0.156,0.198 10 true A 2.385,1.479 2.542,1.677 0.156,0.198 10 true A 2.365,1.729 2.521,1.927 0.156,0.198 10 true A 2.26,1.896 2.417,2.094 0.156,0.198 10 true A 2.365,2.104 2.521,2.302 0.156,0.198 10 true A 1.844,2.573 2,2.771 0.156,0.198 10 true A 1.51,2.542 1.667,2.74 0.156,0.198 10 true A 0.885,2.135 1.042,2.333 0.156,0.198 10 false A 1.052,1.802 1.208,2 0.156,0.198 10 false A 1.021,1.5 1.177,1.698 0.156,0.198 10 false A 1.094,1.177 1.25,1.375 0.156,0.198 10 false A

i.

Temporarily install the timing chain cover assembly with the 20 bolts.

NOTICE:

Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.


HINT:
Bolt Length
Bolt (A) 30 mm (1.18 in.)
Bolt (B) 45 mm (1.77 in.)



ii.

Tighten the 20 bolts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)



Hide 13070A 29.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:

Perform inspection after repair after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A461008C01
0.438,0.865 1.146,0.479 true 2.01,0.76 2.01,0.427 2.01,0.427 2.26,0.427 true 0.5,0.094 0.781,0.448 0.281,0.354 18 false i 4.063,0.083 4.5,0.427 0.438,0.344 18 false ii 0.26,0.792 0.542,1.146 0.281,0.354 10 false *a 2.333,0.354 2.615,0.708 0.281,0.354 10 false *b 4.177,1.052 4.615,1.396 0.438,0.344 18 false iii
*a Knock Pin Hole *b Knock Pin


i.

Align and fit the knock pin of the exhaust camshaft sub-assembly to the knock pin hole of the camshaft timing exhaust gear assembly.


ii.

Using a wrench, hold the hexagonal portion of the exhaust camshaft sub-assembly.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear assembly.




iii.

Using a 5 mm hexagon socket wrench, install the camshaft timing exhaust gear assembly with the 3 bolts and install the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 30.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.
A461568C01
2.219,2.729 2.75,2.354 true 4.885,0.688 5.427,0.354 true 4.875,0.927 5.438,0.344 true 6.125,0.76 5.448,0.365 true 6.135,0.958 5.427,0.375 true 0.469,0.073 0.75,0.427 0.281,0.354 18 false i 0.479,1.594 0.76,1.948 0.281,0.354 18 false ii 4.031,0.052 4.313,0.406 0.281,0.354 18 false iii 2.802,2.229 3,2.427 0.198,0.198 10 true *b 2.323,3.24 2.521,3.438 0.198,0.198 10 true *a 5.375,0.135 5.573,0.333 0.198,0.198 10 true *b
*a 95° *b Timing Mark


i.

Temporarily install the crankshaft pulley bolt.


ii.

Rotate the crankshaft 95° counterclockwise to position the timing mark as shown in the illustration.


iii.

Check that the timing marks of the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.



Hide 13561 31.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Hide 13559 32.INSTALL CHAIN TENSIONER SLIPPER

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Hide 13540 33.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Z101186

HINT:

After replacing or removing and installing the No. 1 chain tensioner assembly, an abnormal noise may occur at start up until the oil in the line has had time to replenish.



Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Hide 13521 34.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

Hide 13506 35.INSTALL CHAIN SUB-ASSEMBLY

a.
A461570C01
2.302,4.031 2.771,4.031 true 1.865,3.719 2.115,3.719 2.115,3.719 2.115,3.969 true 4.115,4.344 4.583,4.781 true 4.115,5.302 4.667,4.958 true 1.323,0.854 1.604,1.208 0.281,0.354 18 false i 4.219,0.802 4.5,1.156 0.281,0.354 18 false ii 0.479,2.688 0.76,3.042 0.281,0.354 18 false iii 4.281,2.667 4.563,3.021 0.281,0.354 18 false iv 2.823,3.948 3.031,4.146 0.208,0.198 10 true *a 1.604,3.625 1.833,3.813 0.229,0.188 10 true *b 3.948,4.177 4.177,4.375 0.229,0.198 10 true *c 3.885,5.281 4.177,5.469 0.292,0.188 10 true *b
*a Paint Mark (Yellow) *b Timing Mark
*c Paint Mark (Orange) - -
V113147

Turn - -


i.

Remove the crankshaft pulley bolt.


ii.

Install the crankshaft timing sprocket and chain sub-assembly.


iii.

Align the paint mark (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.


iv.

Using the hexagonal portion of the exhaust camshaft sub-assembly, rotate the exhaust camshaft sub-assembly counterclockwise with a wrench, align the timing mark of the camshaft timing exhaust gear assembly with the paint mark (orange) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing exhaust gear assembly.



Hide 13050 36.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform inspection after repair after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A461010C01
0.781,3.969 1.365,3.969 true 4.25,1.833 4.417,1.833 4.417,1.833 4.615,1.479 true 4.76,1.708 5.167,2 5.167,2 5.333,2 true 2.063,4.521 2.063,4.104 2.063,4.104 2.313,4.104 true 2.656,0.198 2.969,0.396 0.313,0.198 10 false *a 0.771,0.24 1.219,0.615 0.448,0.375 18 false i 3.969,1.74 4.219,1.927 0.25,0.188 10 true *b 5.385,1.927 5.635,2.115 0.25,0.188 10 true *c 0.5,3.885 0.75,4.073 0.25,0.188 10 true *d 5.583,3.396 5.833,3.583 0.25,0.188 10 true *f 2.354,4.021 2.604,4.208 0.25,0.188 10 true *e 3.677,0.229 4.125,0.604 0.448,0.375 18 false ii 0.865,3.333 1.313,3.708 0.448,0.375 18 false iii 5.115,3.021 5.563,3.396 0.448,0.375 18 false iv 3.813,3.76 4.26,4.135 0.448,0.375 18 false v
*a Loosen *b Paint Mark (Orange)
*c Timing Mark *d Knock Pin Hole
*e Knock Pin *f Hold
V113147

Turn - -


i.

Hold the hexagonal portion of the exhaust camshaft sub-assembly with a wrench and turn the camshaft timing exhaust gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and crankshaft timing sprocket as shown in the illustration.


ii.

Align the paint mark (orange) of the chain sub-assembly with the timing mark of the camshaft timing gear assembly and install the chain sub-assembly to the camshaft timing gear assembly.


iii.

Align and fit the knock pin of the intake camshaft sub-assembly to the knock pin hole of the camshaft timing gear assembly.


iv.

Using a wrench, hold the hexagonal portion of the intake camshaft sub-assembly.

NOTICE:
·

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.




v.

Using a 10 mm bi-hexagonal wrench, install the camshaft timing gear assembly with the bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)



b.

Remove the hexagon wrench with the No. 1 chain tensioner assembly.


Hide 37.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Z101186

Click here(Click here)

Hide 13519 38.INSTALL OIL PUMP DRIVE GEAR

Hide 11320B 39.INSTALL NO. 2 TIMING CHAIN COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 11301C 40.INSTALL TIMING CHAIN COVER OIL SEAL

Z101186

Click here(Click here)

Hide 12315A 41.INSTALL ENGINE MOUNTING BRACKET RH

Hide 11193 42.INSTALL SPARK PLUG TUBE GASKET

a.
A461017N01
0.458,0.063 0.74,0.417 0.281,0.354 18 false i

i.

Install 3 new spark plug tube gaskets to the cylinder head cover sub-assembly.



Hide 11102A 43.INSTALL CAMSHAFT POSITION SENSOR

a.
A461575


Hide 11201 44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A461043C01
0.75,3.917 1.156,3.49 true 0.74,3.927 1.156,3.635 true 2.833,3.5 3.167,3.917 true 2.844,3.625 3.167,3.917 true 1.083,4.25 1.427,3.938 true 1.083,4.25 1.448,4.542 true 3,4.167 2.625,3.802 true 3,4.167 2.521,4.594 true 1.917,5 1.406,4.604 true 1.917,5 1.531,4.531 true 1.917,5 2.573,4.615 true 1.917,5 2.438,4.552 true 0.448,0.115 0.917,0.458 0.469,0.344 18 false i, ii 4.031,0.135 4.5,0.479 0.469,0.344 18 false iii 0.615,2.281 1.083,2.625 0.469,0.344 18 false iv 0.563,3.844 0.875,4.042 0.313,0.198 10 false *a 3.208,3.896 3.521,4.094 0.313,0.198 10 false *a 3.052,4.094 3.365,4.292 0.313,0.198 10 false *a 0.906,4.156 1.219,4.354 0.313,0.198 10 false *a 1.833,5.052 2.031,5.24 0.198,0.188 10 true *b 5.667,3.031 5.792,3.208 0.125,0.177 10 true B 5.448,2.844 5.573,3.021 0.125,0.177 10 true B 5.104,2.844 5.229,3.021 0.125,0.177 10 true B 5.552,2.135 5.677,2.313 0.125,0.177 10 true B 4.542,3.302 4.667,3.479 0.125,0.177 10 true A 5.115,3.354 5.24,3.531 0.125,0.177 10 true A 5.51,3.354 5.635,3.531 0.125,0.177 10 true A 5.854,3.354 5.979,3.531 0.125,0.177 10 true A 6.344,3.146 6.469,3.323 0.125,0.177 10 true A 6.458,2.656 6.583,2.833 0.125,0.177 10 true A 6.167,1.896 6.292,2.073 0.125,0.177 10 false A 5.729,1.896 5.854,2.073 0.125,0.177 10 false A 5.198,1.906 5.323,2.083 0.125,0.177 10 false A 4.719,1.885 4.844,2.063 0.125,0.177 10 false A 4.396,2.625 4.521,2.802 0.125,0.177 10 false A 4.406,4.531 4.542,4.708 0.135,0.177 10 false 9 5.521,4.031 5.656,4.208 0.135,0.177 10 true 1 5.677,4.927 5.813,5.104 0.135,0.177 10 true 2 5.115,4.708 5.25,4.885 0.135,0.177 10 true 3 5.479,4.708 5.615,4.885 0.135,0.177 10 true 4 5.125,3.76 5.448,3.979 0.323,0.219 10 false 5, 11 5.427,5.229 5.75,5.448 0.323,0.219 10 true 6, 17 5.104,5.25 5.24,5.427 0.135,0.177 10 true 7 4.531,5.188 4.667,5.365 0.135,0.177 10 true 8 4.688,3.76 4.854,3.927 0.167,0.167 10 false 10 5.698,3.76 5.865,3.927 0.167,0.167 10 false 12 6.125,3.771 6.292,3.938 0.167,0.167 10 false 13 6.458,4.531 6.656,4.698 0.198,0.167 10 false 14 6.354,5.01 6.552,5.188 0.198,0.177 10 false 15 5.813,5.26 6.01,5.438 0.198,0.177 10 true 16 3.823,2.052 4.813,2.458 0.99,0.406 18 false v, vi 4.021,4 4.49,4.344 0.469,0.344 18 false vii
*a Seal Packing Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.) *b Mark
V100143

Seal Packing - -


i.

Apply a light coat of engine oil to the new camshaft bearing cap oil hole gasket.


ii.

Install a new camshaft bearing cap oil hole gasket to the No. 1 camshaft bearing cap.


iii.

Install 5 new cylinder head cover gaskets to the cylinder head cover sub-assembly.


iv.

Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover subassembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.




v.

Install the cylinder head cover sub-assembly to the camshaft housing sub-assembly.


vi.

Temporarily install the cylinder head cover sub-assembly and camshaft position sensor with the 15 bolts.

HINT:
Bolt Length Thread Diameter
Bolt (A) 23.5 mm (0.925 in.) 6 mm (0.24 in.)
Bolt (B) 30 mm (1.18 in.) 6 mm (0.24 in.)



vii.

Using an 8 mm socket wrench, install the 2 camshaft position sensors (for Exhaust Side and for Intake Side) and cylinder head cover sub-assembly with 4 new bolts (B) and the 11 bolts (A) in the order shown in the illustration.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·

Do not add oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.





Hide 16305E 45.INSTALL OUTLET WATER BY-PASS SUB-ASSEMBLY

a.
A459959N01
0.438,0.094 0.719,0.448 0.281,0.354 18 false i

i.

Using an 8 mm socket wrench, install the outlet water by-pass sub-assembly and a new outlet water pipe gasket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 16304 46.INSTALL OUTLET WATER SUB-ASSEMBLY

a.
A459958N01
0.5,0.094 0.781,0.448 0.281,0.354 18 false i

i.

Using an 8 mm socket wrench, install the outlet water sub-assembly and a new outlet water gasket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 13470 47.INSTALL CRANKSHAFT PULLEY ASSEMBLY

a.
A461572C01
4.354,0.927 4.771,0.51 false 4.365,0.927 5.031,0.865 true 4.302,0.385 4.615,0.583 0.313,0.198 10 false *a 5.365,1.427 5.583,1.635 0.219,0.208 10 true *b 4.083,0.896 4.49,1.125 0.406,0.229 10 false SST 0.875,0.063 1.156,0.417 0.281,0.354 18 false i 3.719,0.031 4,0.385 0.281,0.354 18 false ii
*a Hold *b Turn


i.

Align the crankshaft timing gear key with the key groove of the crankshaft pulley assembly.


ii.

Using SST, hold the crankshaft pulley assembly and install the crankshaft pulley set bolt.

SST
09213-54015  
09330-00021  

Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)



Hide 29300 48.INSTALL VACUUM PUMP ASSEMBLY

Z101186

Click here(Click here)

Hide 12204C 49.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Z101186

Click here(Click here)

Hide 11401G 50.INSTALL CRANKSHAFT POSITION SENSOR

Z101186

Click here(Click here)

Hide 12108A 51.INSTALL OIL FILLER CAP GASKET

Hide 12180E 52.INSTALL OIL FILLER CAP ASSEMBLY

Hide 16032 53.INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

Z101186

Click here(Click here)

Hide 16031 54.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 15370 55.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)

Z101186

Click here(Click here)

Hide 15370 56.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

Z101186

Click here(Click here)

Hide 89448D 57.INSTALL OIL PRESSURE AND TEMPERATURE SENSOR

Z101186

Click here(Click here)

Hide 89615 58.INSTALL KNOCK SENSOR

Z101186

Click here(Click here)

Hide 19100P 59.INSTALL SPARK PLUG

Z101186

Click here(Click here)