Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD
RM3700E _51 Engine / Hybrid System _093330 M15A-FKS ENGINE MECHANICAL _0440541 CYLINDER HEAD A

M15A-FKS ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
A479316N01
5.167,0.5 5.833,0.667 0.667,0.167 3.917,0.167 4.604,0.333 0.688,0.167 5.375,3 5.625,3.333 5.625,3.333 5.792,3.333 false 2.667,2 2.833,2 2.833,2 3.271,2.208 false 0.844,1.875 0.49,2.677 0.49,2.677 0.49,2.844 false 5.448,4.083 5.448,4.396 false 4.563,1.385 5,0.583 5,0.583 5.167,0.583 false 3.667,2.094 3.75,0.25 3.75,0.25 3.917,0.25 false 2.344,1.458 2.51,1.458 2.51,1.458 3.167,1.813 false 2.448,1.021 2.615,1.021 2.615,1.021 3.198,1.51 false 2.771,4.844 3.229,4.844 false 3.552,5.083 4.135,5.083 false 5.031,1.229 5.156,1.229 false 5.354,1.073 5.698,1.146 5.698,1.146 5.865,1.146 false 4.531,2.583 5.865,2.583 false 4.74,2.333 5.156,2.333 false 4.813,2.083 5.813,2.083 false 5.083,1.667 5.833,1.667 false 2.333,0.167 2.5,0.167 2.5,0.167 3.094,0.313 false 2.417,0.667 2.583,0.667 2.583,0.667 3.083,0.844 false 2.75,0.417 2.917,0.417 2.917,0.417 3.063,0.51 false 2.51,1.844 2.792,2.198 0.281,0.354 18 false 1 6.469,2.417 6.75,2.771 0.281,0.354 18 false 2 0.594,2.865 0.875,3.219 0.281,0.354 18 false 3 6.469,3.167 6.75,3.521 0.281,0.354 18 false 4 5.552,4.385 5.833,4.74 0.281,0.354 18 false 5 6.25,3.25 6.531,3.604 0.281,0.354 10 false ● 6.427,0.458 6.708,0.813 0.281,0.354 18 false 6 5.104,0.146 5.385,0.5 0.281,0.354 18 false 7 5.188,0.5 6.104,0.75 0.917,0.25 8 false 44 (449, 32) 3.938,0.167 5.198,0.354 1.26,0.188 8 false 25 (255, 18) 2.083,1.313 2.365,1.667 0.281,0.354 18 false 8 5.167,2.188 5.448,2.542 0.281,0.354 18 false 9 2.125,0.906 2.688,1.167 0.563,0.26 18 false 10 6.417,1.917 6.958,2.25 0.542,0.333 18 false 11 4.5,4.99 5.177,5.365 0.677,0.375 18 false 12 2.458,4.729 3,5.073 0.542,0.344 18 false 13 6.24,1.479 6.781,1.792 0.542,0.313 18 false 15 2.094,0.542 2.531,0.896 0.438,0.354 18 false 14 4.719,1.094 5.24,1.417 0.521,0.323 18 false 16 2.417,0.313 2.844,0.646 0.427,0.333 18 false 16 2.052,0.063 2.438,0.406 0.385,0.344 18 false 17 6.219,1.063 6.75,1.375 0.531,0.313 18 false 17 6.25,1.979 6.531,2.333 0.281,0.354 10 false ● 6.25,0.521 6.531,0.875 0.281,0.354 10 false ★ 4.938,0.198 5.219,0.552 0.281,0.354 10 false ★ 1.99,0.969 2.271,1.323 0.281,0.354 10 false ● 6.25,2.5 6.531,2.854 0.281,0.354 10 false ● 2.354,1.896 2.635,2.25 0.281,0.354 10 false ● 3.229,0.219 3.688,0.417 0.458,0.198 10 false x6 5.365,0.917 5.823,1.115 0.458,0.198 10 false x6 5.333,1.198 5.792,1.396 0.458,0.198 10 false x6 3.25,0.438 3.708,0.635 0.458,0.198 10 false x6 3.323,0.948 3.781,1.146 0.458,0.198 10 false x6 3.344,1.469 3.802,1.667 0.458,0.198 10 false x6 3.375,2.167 3.833,2.365 0.458,0.198 10 false x6 3.396,1.771 3.854,1.969 0.458,0.198 10 false x6 4.5,2.719 4.958,2.917 0.458,0.198 10 false x6 4.729,2.365 5.188,2.563 0.458,0.198 10 false x6 4.823,2.094 5.281,2.292 0.458,0.198 10 false x6 5.042,1.75 5.5,1.948 0.458,0.198 10 false x6 3.813,2.052 4.271,2.25 0.458,0.198 10 false x3 1.104,1.74 1.563,1.938 0.458,0.198 10 false x3 3.146,5.156 3.604,5.354 0.458,0.198 10 false x6 3.688,5.24 4.146,5.438 0.458,0.198 10 false x6 5.594,4.094 6.052,4.292 0.458,0.198 10 false x6 5.125,2.969 5.583,3.167 0.458,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INTAKE VALVE GUIDE BUSH 11122 (Click here) - -
2 EXHAUST VALVE GUIDE BUSH 11126 (Click here) - -
3 SPARK PLUG TUBE - (Click here) - -
4 RING PIN 11115A (Click here) - -
5 STUD BOLT 17159 (Click here) - -
6 NO. 2 STRAIGHT SCREW PLUG 11117F (Click here) - -
7 NO. 1 STRAIGHT SCREW PLUG 11117E (Click here) - -
8 INTAKE VALVE SPRING SEAT 13734A - - -
9 EXHAUST VALVE SPRING SEAT 13734B - - -
10 INTAKE VALVE STEM OIL SEAL 13711E (Click here) - -
11 EXHAUST VALVE STEM OIL SEAL 13715A (Click here) - -
12 INTAKE VALVE 13711 (Click here) - -
13 EXHAUST VALVE 13715 (Click here) - -
14 INTAKE VALVE COMPRESSION SPRING 13711M (Click here) - -
15 EXHAUST VALVE COMPRESSION SPRING 13715H (Click here) - -
16 VALVE SPRING RETAINER - - - -
17 VALVE SPRING RETAINER LOCK 13741A (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Adhesive 1324 ★ Precoated part

PROCEDURE

Hide 11122 1.INSTALL INTAKE VALVE GUIDE BUSH

a.
A461383C01
2.24,4.313 2.781,3.948 true 0.823,4.083 1.583,3.438 true 0.813,4.094 1.542,3.615 true 2.063,4.271 2.26,4.427 0.198,0.156 10 true *a 0.563,0.115 0.844,0.469 0.281,0.354 18 false i 0.604,2.552 0.885,2.906 0.281,0.354 18 false iii 4.167,2.573 4.448,2.927 0.281,0.354 18 false iv 4.188,0.125 4.469,0.479 0.281,0.354 18 false ii 0.51,4.042 0.875,4.26 0.365,0.219 10 false SST
*a Protrusion Height - -


i.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Specified Condition
STD 10.333 to 10.344 mm
(0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm
(0.40877 to 0.40921 in.)


HINT:
·

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 intake valve guide bush.

·

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.




ii.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



iii.

Using SST and a hammer, tap in the selected intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

13.35 to 13.60 mm (0.526 to 0.535 in.)



iv.

Using a reamer, ream the intake valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)




Hide 11126 2.INSTALL EXHAUST VALVE GUIDE BUSH

a.
A461384C01
3,4 3.583,4 true 1.365,3.49 2.396,3.188 true 1.448,3.688 2.417,3.188 true 0.51,0.052 0.792,0.406 0.281,0.354 18 false i 0.5,2.448 0.781,2.802 0.281,0.354 18 false iii 4.219,2.438 4.5,2.792 0.281,0.354 18 false iv 4.208,0.042 4.5,0.427 0.292,0.385 18 false ii 3.656,3.938 3.854,4.094 0.198,0.156 10 true *a 2.479,3.094 2.854,3.375 0.375,0.281 10 false SST
*a Protrusion Height - -


i.

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


New Guide Bush Selection Chart:
Bush Size Specified Condition
STD 10.333 to 10.344 mm
(0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm
(0.40877 to 0.40921 in.)


HINT:
·

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 exhaust valve guide bush.

·

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.




ii.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).

CAUTION:

Be sure to wear protective gloves.



iii.

Using SST and a hammer, tap in the selected exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

13.75 to 14.00 mm (0.541 to 0.551 in.)



iv.

Using a reamer, ream the exhaust valve guide bush to obtain the standard oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)




Hide 3.INSTALL SPARK PLUG TUBE

Z101186

HINT:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.



a.
A460726C01
2.417,2.396 2.417,1.979 false 2.354,2.438 2.667,2.635 0.313,0.198 10 false *a 1.875,2.573 2.188,2.771 0.313,0.198 10 false *b 5.875,2.438 6.188,2.635 0.313,0.198 10 false *d 1.896,1.5 2.208,1.698 0.313,0.198 10 false *c 0.865,0.802 1.146,1.156 0.281,0.354 18 false i 4.229,0.094 4.51,0.448 0.281,0.354 18 false ii
*a Adhesive *b 1.0 mm (0.0394 in.)
*c 1.0 to 7.0 mm (0.0394 to 0.276 in.) *d Protrusion Height


i.

Apply adhesive to a new spark plug tube as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



ii.

Using a wooden block and hammer, tap in the 3 spark plug tubes to the specified protrusion height.

Standard Protrusion Height:

77.3 to 78.3 mm (3.04 to 3.08 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.




Hide 11115A 4.INSTALL RING PIN

a.
A460710C01
5.688,0.75 6,0.948 0.313,0.198 10 false *a 0.5,0.083 0.781,0.438 0.281,0.354 18 false i
*a Protrusion Height - -


i.

Using a plastic hammer, tap in 2 new ring pins to the cylinder head sub-assembly.

Standard Protrusion Height:

6.5 to 7.5 mm (0.256 to 0.295 in.)




Hide 17159 5.INSTALL STUD BOLT

a.
A460711C01
0.469,0.052 0.75,0.406 0.281,0.354 18 false i 5.396,0.76 5.708,0.958 0.313,0.198 10 false *a 5.385,1.135 5.698,1.333 0.313,0.198 10 false *b 5.781,0.958 6.094,1.156 0.313,0.198 10 false *c
*a 22 mm (0.866 in.) *b 13 mm (0.512 in.)
*c 35 mm (1.378 in.) - -


i.

Using an E8 "TORX" socket wrench, install the 6 stud bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)



Hide 11117F 6.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A461385N01
0.5,0.073 0.781,0.427 0.281,0.354 18 false i 4.167,0.063 4.448,0.417 0.281,0.354 18 false ii

i.

Apply adhesive to the No. 2 straight screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the No. 2 straight screw plug within 3 minutes of applying adhesive.



ii.

Using a 10 mm straight hexagon wrench, install the No. 2 straight screw plug to the cylinder head sub-assembly.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 11117E 7.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A461385N01
0.5,0.073 0.781,0.427 0.281,0.354 18 false i 4.167,0.063 4.448,0.417 0.281,0.354 18 false ii

i.

Apply adhesive to the 3 No. 1 straight screw plugs.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the No. 1 straight screw plug within 3 minutes of applying adhesive.



ii.

Using a 6 mm straight hexagon wrench, install the 3 No. 1 straight screw plugs to the cylinder head sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)



Hide 13734A 8.INSTALL INTAKE VALVE SPRING SEAT

Hide 13734B 9.INSTALL EXHAUST VALVE SPRING SEAT

Hide 13711E 10.INSTALL INTAKE VALVE STEM OIL SEAL

a.
A461378C01
2.167,2 2.333,2 2.333,2 2.583,1.75 true 1.083,1.75 1.25,2 1.25,2 1.417,2 true 3.875,0.583 4.792,0.583 true 5.833,1.167 6.5,1.5 true 1.052,0.573 1.365,0.771 0.313,0.198 10 false *a 2.531,0.563 2.844,0.76 0.313,0.198 10 false *b 1.49,1.969 1.802,2.167 0.313,0.198 10 false *c 1.917,1.969 2.229,2.167 0.313,0.198 10 false *d 4.646,1.677 4.958,1.875 0.313,0.198 10 false *e 6.365,1.688 6.677,1.885 0.313,0.198 10 false *f 3.583,0.51 3.896,0.708 0.313,0.198 10 false SST 6.573,1.469 6.885,1.667 0.313,0.198 10 false SST 0.531,0.063 0.896,0.438 0.365,0.375 18 false i 3.938,0.063 4.302,0.438 0.365,0.375 18 false ii
*a Intake Valve Stem Oil Seal *b Exhaust Valve Stem Oil Seal
*c Gold *d Gray
*e Correct *f Incorrect


i.

Apply a light coat of engine oil to 6 new intake valve stem oil seals.

NOTICE:

Make sure to install each valve stem oil seal to the correct side. Installing an intake valve stem oil seal to the exhaust side or installing an exhaust valve stem oil seal to the intake side can cause installation problems later.


HINT:

The intake valve stem oil seals are gold and the exhaust valve stem oil seals are gray.



ii.

Using SST, push in the 6 intake valve stem oil seals.

SST
09201-41020  

NOTICE:
·

Failure to use SST will cause the valve stem oil seals to be damaged or improperly seated.

·

Do not push in the valve stem oil seals at an angle.





Hide 13715A 11.INSTALL EXHAUST VALVE STEM OIL SEAL

a.

Install using the same procedure as for the intake valve stem oil seal.


Hide 13711 12.INSTALL INTAKE VALVE

a.
A461949N01
0.5,0.073 0.781,0.427 0.281,0.354 18 false i 4.073,0.094 4.354,0.448 0.281,0.354 18 false ii

i.

Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.


ii.

Install the 6 intake valves to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.




Hide 13715 13.INSTALL EXHAUST VALVE

a.

Install using the same procedure as for the intake valve.


Hide 13711M 14.INSTALL INTAKE VALVE COMPRESSION SPRING

Z101186

NOTICE:
·

Install so that the tapered side of the intake valve compression spring is facing upward (toward the valve spring retainer side).

·

Install the same parts in the same combination to their original locations.




Hide 13715H 15.INSTALL EXHAUST VALVE COMPRESSION SPRING

Z101186

NOTICE:
·

Install so that the tapered side of the exhaust valve compression spring is facing upward (toward the valve spring retainer side).

·

Install the same parts in the same combination to their original locations.




Hide 16.INSTALL VALVE SPRING RETAINER

Hide 13741A 17.INSTALL VALVE SPRING RETAINER LOCK

a.
A461948N01
0.427,0.042 0.708,0.396 0.281,0.354 18 false i 4.021,0.021 4.302,0.375 0.281,0.354 18 false ii

i.

Using SST, compress each compression spring and install the 12 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

NOTICE:

Install the same parts in the same combination to their original locations.



ii.

Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the valve spring retainer.