|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
Adhesive 1324 | ★ | Precoated part |
11122
1.INSTALL INTAKE VALVE GUIDE BUSH
| *a | Protrusion Height | - | - |
Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.
10.285 to 10.306 mm (0.405 to 0.406 in.)
| Bush Size | Specified Condition |
|---|---|
| STD | 10.333 to 10.344 mm
(0.40681 to 0.40724 in.) |
| O/S 0.05 | 10.383 to 10.394 mm
(0.40877 to 0.40921 in.) |
If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the intake valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 intake valve guide bush.
If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.
Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).
Be sure to wear protective gloves.
Using SST and a hammer, tap in the selected intake valve guide bush.
13.35 to 13.60 mm (0.526 to 0.535 in.)
Using a reamer, ream the intake valve guide bush to obtain the standard oil clearance.
0.025 to 0.060 mm (0.000984 to 0.00236 in.)
11126
2.INSTALL EXHAUST VALVE GUIDE BUSH
| *a | Protrusion Height | - | - |
Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.
10.285 to 10.306 mm (0.405 to 0.406 in.)
| Bush Size | Specified Condition |
|---|---|
| STD | 10.333 to 10.344 mm
(0.40681 to 0.40724 in.) |
| O/S 0.05 | 10.383 to 10.394 mm
(0.40877 to 0.40921 in.) |
If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.306 mm (0.406 in.), machine the exhaust valve guide bush bore of the cylinder head sub-assembly to a dimension of 10.335 to 10.356 mm (0.407 to 0.408 in.) to install an O/S 0.05 exhaust valve guide bush.
If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.
Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).
Be sure to wear protective gloves.
Using SST and a hammer, tap in the selected exhaust valve guide bush.
13.75 to 14.00 mm (0.541 to 0.551 in.)
Using a reamer, ream the exhaust valve guide bush to obtain the standard oil clearance.
0.030 to 0.065 mm (0.00118 to 0.00256 in.)
3.INSTALL SPARK PLUG TUBE
|
|
| *a | Adhesive | *b | 1.0 mm (0.0394 in.) |
| *c | 1.0 to 7.0 mm (0.0394 to 0.276 in.) | *d | Protrusion Height |
Apply adhesive to a new spark plug tube as shown in the illustration.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Using a wooden block and hammer, tap in the 3 spark plug tubes to the specified protrusion height.
77.3 to 78.3 mm (3.04 to 3.08 in.)
To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.
11115A
4.INSTALL RING PIN
| *a | Protrusion Height | - | - |
Using a plastic hammer, tap in 2 new ring pins to the cylinder head sub-assembly.
6.5 to 7.5 mm (0.256 to 0.295 in.)
17159
5.INSTALL STUD BOLT
| *a | 22 mm (0.866 in.) | *b | 13 mm (0.512 in.) |
| *c | 35 mm (1.378 in.) | - | - |
Using an E8 "TORX" socket wrench, install the 6 stud bolts.
11117F
6.INSTALL NO. 2 STRAIGHT SCREW PLUG
Apply adhesive to the No. 2 straight screw plug.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the No. 2 straight screw plug within 3 minutes of applying adhesive.
Using a 10 mm straight hexagon wrench, install the No. 2 straight screw plug to the cylinder head sub-assembly.
11117E
7.INSTALL NO. 1 STRAIGHT SCREW PLUG
Apply adhesive to the 3 No. 1 straight screw plugs.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the No. 1 straight screw plug within 3 minutes of applying adhesive.
Using a 6 mm straight hexagon wrench, install the 3 No. 1 straight screw plugs to the cylinder head sub-assembly.
13734A
8.INSTALL INTAKE VALVE SPRING SEAT
13734B
9.INSTALL EXHAUST VALVE SPRING SEAT
13711E
10.INSTALL INTAKE VALVE STEM OIL SEAL
| *a | Intake Valve Stem Oil Seal | *b | Exhaust Valve Stem Oil Seal |
| *c | Gold | *d | Gray |
| *e | Correct | *f | Incorrect |
Apply a light coat of engine oil to 6 new intake valve stem oil seals.
Make sure to install each valve stem oil seal to the correct side. Installing an intake valve stem oil seal to the exhaust side or installing an exhaust valve stem oil seal to the intake side can cause installation problems later.
The intake valve stem oil seals are gold and the exhaust valve stem oil seals are gray.
Using SST, push in the 6 intake valve stem oil seals.
Failure to use SST will cause the valve stem oil seals to be damaged or improperly seated.
Do not push in the valve stem oil seals at an angle.
13715A
11.INSTALL EXHAUST VALVE STEM OIL SEAL
Install using the same procedure as for the intake valve stem oil seal.
13711
12.INSTALL INTAKE VALVE
Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.
Install the 6 intake valves to the cylinder head sub-assembly.
Install the same parts in the same combination to their original locations.
13715
13.INSTALL EXHAUST VALVE
Remove using the same procedure as for the intake valve.
13711M
14.INSTALL INTAKE VALVE COMPRESSION SPRING
|
|
13715H
15.INSTALL EXHAUST VALVE COMPRESSION SPRING
|
|
16.INSTALL VALVE SPRING RETAINER
13741A
17.INSTALL VALVE SPRING RETAINER LOCK
Using SST, compress each compression spring and install the 12 valve spring retainer locks.
Install the same parts in the same combination to their original locations.
Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.
Be careful not to damage the valve stem tip.
Be careful not to damage the valve spring retainer.