MALFUNCTION DESCRIPTION
This DTC is stored when the inverter water pump assembly is malfunctioning. The cause of this malfunction may be one of the following:
Inverter water pump assembly internal malfunction
Open or short in wire harness
Improperly connected connector
Foreign matter in inverter water pump assembly
Hybrid cooling system coolant is frozen
If this DTC is stored, the driving torque may be restricted.
The inverter water pump assembly transmits rotation speed information to the hybrid vehicle control ECU. The hybrid vehicle control ECU monitors the speed and detects malfunctions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P0C7396 | Motor Electronics Coolant Pump "A" Component Internal Failure | The inverter water pump assembly revolution speed is abnormally high or low (or stopped) for 1 minute or more.
(1 trip detection logic) |
·
Inverter cooling system ·
Wire harness or connector ·
Inverter water pump assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning: Comes on | Hybrid Control | A |
The inverter water pump assembly operates when the ignition switch is ON (READY).
| DTC No. | Data List |
|---|---|
| P0C7396 | ·
Inverter Water Pump Revolution ·
Inverter Water Pump Duty Ratio ·
Inverter Coolant Water Temperature |
| DTC No. | Active Test |
|---|---|
| P0C7396 | Activate the Inverter Water Pump |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY).
Wait for 2 minutes or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the inverter water pump assembly may suspend control as a self-protection function and store DTCs.
(When the auxiliary battery voltage returns to normal, the inverter water pump assembly will resume normal operation. In this case it is not necessary to replace the inverter water pump assembly.)
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| Only P0C7396 for Hybrid Control System is output | A |
| P0C7396 and DTCs other than the DTCs in the table below are output | B |
| P0C7396 and any DTCs in the table below are output | C |
| System | Relevant DTC | |
|---|---|---|
| Hybrid Control System | P0C7396 | Motor Electronics Coolant Pump "A" Component Internal Failure |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Microcomputer malfunction | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P06881F | ECM/PCM Power Relay Sense Circuit Intermittent | |
| Sensor and actuator circuit malfunction | P314A31 | Motor Electronics Coolant Pump "A" No Signal |
P0C7396 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
C
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.
Pre-procedure1
None.
Procedure1
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Inverter Water Pump Revolution |
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter Water Pump Revolution | Ignition switch ON | 200 rpm or less |
When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Make sure that the HV coolant level is above the low line of the inverter reserve tank.
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Pre-procedure1
None.
Procedure1
According to the display on the GTS, perform the Active Test "Activate the Inverter Water Pump" and, check the value of the Data List item "Inverter Water Pump Revolution".
| Active Test Display |
|---|
| Activate the Inverter Water Pump |
| Data List Display |
|---|
| Inverter Water Pump Revolution |
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter Water Pump Revolution | Ignition switch ON
During Active Test |
3200 to 8600 rpm |
Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).
When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Cooling System
| Result | Proceed to |
|---|---|
| Ambient Temperature value is above freezing temperature of the HV coolant | A |
| Ambient Temperature value is below freezing temperature of the HV coolant | B |
A
B
| Proceed to |
|---|
| NEXT |
NEXT
After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.
Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Cooling System
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.
Pre-procedure1
Disconnect the A68 hybrid vehicle control ECU connector.
Disconnect the A59 inverter water pump assembly connector.
Procedure1
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A68,A59)Location & Routingewd_type=routing;type=c,c;code=A68,A59 Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=A68;pinno=31 Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)ewd_type=component;type=c;code=A59;pinno=3 |
||
| A68-31 (IWP) - A59-3 (SWP) | Ignition switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A68,A59)Location & Routingewd_type=routing;type=c,c;code=A68,A59 Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=A68;pinno=31 Click Connector(A59)Engine Compartment>Engine Room Main Wire>Inverter Water Pump Assembly (with Motor)ewd_type=component;type=c;code=A59;pinno=3 |
||
| A68-31 (IWP) or A59-3 (SWP) - Body ground and other terminals | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the A59 inverter water pump assembly connector.
Reconnect the A68 hybrid vehicle control ECU connector.
OK
NG
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Pre-procedure1
| *1 | No. 5 Relay Block Assembly |
| *2 | INV W/P Fuse |
Remove the INV W/P fuse from No. 5 relay block assembly.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Water Pump Revolution.
| Tester Display |
|---|
| Inverter Water Pump Revolution |
Procedure1
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter Water Pump Revolution | Ignition switch ON | 200 rpm or less |
| Result | Proceed to |
|---|---|
| The value of Inverter Water Pump Revolution is 200 rpm or less | A |
| None of the above conditions are met | B |
Post-procedure1
Turn the ignition switch off.
Reinstall the INV W/P fuse.
A
B
Pre-procedure1
Disconnect the A68 hybrid vehicle control ECU connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
*b | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A68,H44)Location & Routingewd_type=routing;type=c,c;code=A68,H44 Click Connector(A68)Instrument Panel>Engine Room Main Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=A68;pinno=31 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=15 |
||
| A68-31 (IWP) - H44-15 (E1) | Ignition switch ON | 11 to 14 V |
Turning the ignition switch to ON with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
Reconnect the A68 hybrid vehicle control ECU connector.
OK
NG
Pre-procedure1
Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.
Turn the ignition switch to ON.
Procedure1
While turning the ignition switch to ON, check the waveform between the hybrid vehicle control ECU terminals.
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
- | - |
| Item | Content |
|---|---|
| Terminal | A68-31 (IWP) - H44-15 (E1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Ignition switch ON |
Waveform duty ratio is between 3% and 9%.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Turn the ignition switch off.
OK
NG