Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441185 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  U115087  Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message  


DESCRIPTION

The battery ECU assembly transmits and receives signals via CAN communication to and from the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate DTC Output from Priority
U115087 Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message The battery ECU assembly does not receive any signals from the hybrid vehicle control ECU for 1 second or more.
(1 trip detection logic)
·

Battery ECU assembly

·

Hybrid vehicle control ECU

·

Wire harness or connector


Comes on Master Warning:
Comes on
HV Battery B

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A459863E04
5.802,0.698 6.406,1.156 0.604,0.458 10 false +B1 5.802,1.125 6.406,1.583 0.604,0.458 10 false +B2 5.813,1.542 6.417,2 0.604,0.458 10 false MREL 5.521,0.594 5.813,0.813 0.292,0.219 10 false 7 3.646,1.323 4.344,1.594 0.698,0.271 10 false PM IGCT 2.615,1.906 3.583,2.188 0.969,0.281 10 false IGCT 1.198,1.333 2,1.896 0.802,0.563 10 false IGCT-MAIN 0.813,4.448 2.25,5.01 1.438,0.563 10 false Auxiliary Battery 0.979,5.417 2.885,5.729 1.906,0.313 10 false : CAN Communication Line 3.635,1.042 3.885,1.365 0.25,0.323 10 false 1 4.167,1.031 4.417,1.354 0.25,0.323 10 false 2 3.115,1.469 3.365,1.792 0.25,0.323 10 false 1 2.375,1.458 2.719,1.708 0.344,0.25 10 false 2 2.365,1.063 2.708,1.313 0.344,0.25 10 false 3 3.125,1.021 3.469,1.271 0.344,0.25 10 false 5 5.292,4.958 7.083,5.375 1.792,0.417 10 false Hybrid Vehicle Control ECU 3.083,4.688 5.146,4.979 2.063,0.292 10 false Battery ECU Assembly 3.844,3.479 4.74,3.771 0.896,0.292 10 false CA1H 3.865,4.104 4.76,4.396 0.896,0.292 10 false CA1L 5.76,3.49 6.656,3.781 0.896,0.292 10 false CA4H 5.781,4.115 6.677,4.406 0.896,0.292 10 false CA4L 5.469,3.917 5.75,4.146 0.281,0.229 10 false 23 5.458,3.292 5.74,3.521 0.281,0.229 10 false 10 3.094,4.479 3.375,4.708 0.281,0.229 10 false z12 5.292,4.75 5.573,4.979 0.281,0.229 10 false H44 4.365,3.323 4.646,3.552 0.281,0.229 10 false 36 4.365,3.927 4.646,4.156 0.281,0.229 10 false 35 5.521,1.01 5.813,1.229 0.292,0.219 10 false 8 5.458,1.417 5.75,1.635 0.292,0.219 10 false 47

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*

-

Disconnecting the low voltage connector of the HV battery


*: for AWD


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.


*: for AWD




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

a.

Check and record any Hybrid Control DTCs and freeze frame data.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK HYBRID VEHICLE CONTROL ECU (VOLTAGE)

B

2.CHECK HYBRID VEHICLE CONTROL ECU (VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

A458550C15
4.688,0.26 5.125,0.542 0.438,0.281 4.354,2.396 4.813,1.281 true 5.563,2.406 5.01,1.281 true 0.25,0.167 0.563,0.323 0.313,0.156 10 false *a 5.49,2.448 5.906,2.635 0.417,0.188 10 false +B1 4.229,2.448 4.677,2.719 0.448,0.271 10 false +B2 4.802,0.333 5.135,0.583 0.333,0.25 10 false H44
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H44)Location & Routing

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

H44-7 (+B1) - Body ground Ignition switch ON 11 to 14 V
H44-8 (+B2) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

3.CHECK BATTERY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK BATTERY ECU ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A459571C07
1.49,0.115 1.948,0.427 0.458,0.313 1.677,2.875 2.073,2.219 true 2.719,2.875 2.302,2.208 true 2.188,2.875 2.177,2.219 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 2.615,2.917 3.083,3.146 0.469,0.229 10 false CA1H 1.552,2.917 1.99,3.115 0.438,0.198 10 false GND 2.063,2.917 2.531,3.146 0.469,0.229 10 false CA1L
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-36 (CA1H) - z12-34 (GND) Ignition switch ON 2.5 to 3.5 V
z12-35 (CA1L) - z12-34 (GND) Ignition switch ON 1.5 to 2.5 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-36 (CA1H) - z12-35 (CA1L) Ignition switch off 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the z12 battery ECU assembly connector.


b.

Install the No. 1 HV battery hose.



OK

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the H44 hybrid vehicle control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU and battery ECU assembly is not loose or disconnected.




c.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



d.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A459864C01
4.875,0.438 5.302,0.75 0.427,0.313 1.688,0.125 2.115,0.438 0.427,0.313 2.688,2.344 2.385,1.802 true 2.031,2.313 2.302,1.802 true 6.125,2.26 5.688,1.438 true 5.156,2.26 5.552,1.573 true 0.813,0.26 1.125,0.458 0.313,0.198 10 false *a 3.833,0.26 4.146,0.458 0.313,0.198 10 false *b 1.802,0.229 2.26,0.427 0.458,0.198 10 false z12 4.958,0.521 5.417,0.719 0.458,0.198 10 false H44 1.875,2.385 2.333,2.583 0.458,0.198 10 false CA1L 2.542,2.396 3,2.594 0.458,0.198 10 false CA1H 5.99,2.313 6.448,2.51 0.458,0.198 10 false CA4H 4.979,2.302 5.438,2.5 0.458,0.198 10 false CA4L
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12,H44)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECU

z12-36 (CA1H) - H44-10 (CA4H) Ignition switch off Below 1 Ω
z12-35 (CA1L) - H44-23 (CA4L) Ignition switch off Below 1 Ω
H44-10 (CA4H) - Other terminals and body ground Ignition switch off 10 kΩ or higher
H44-23 (CA4L) - Other terminals and body ground Ignition switch off 10 kΩ or higher



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z12)Location & Routing

Click Connector(z12)Body>other>Battery ECU Assembly , HV Supply Battery Assembly

z12-36 (CA1H) - Body ground Ignition switch ON Below 1 V
z12-35 (CA1L) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the z12 battery ECU assembly connector.


d.

Install the No. 1 HV battery hose.


e.

Reconnect the H44 hybrid vehicle control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR