Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY ECU › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441189 BATTERY ECU A

HYBRID / BATTERY CONTROL  BATTERY ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472777N05
4.344,3.344 4.052,3.344 false 1.521,0.323 1.844,0.323 false 3.396,0.635 3.708,0.635 false 6.552,0.188 6.865,0.188 false 3.896,3.188 4.177,3.542 0.281,0.354 18 false 3 1.083,0.167 1.74,0.51 0.656,0.344 18 false 4, 8 5.75,0.052 6.667,0.51 0.917,0.458 18 false 1, 2, 6 4.167,0.479 4.823,0.823 0.656,0.344 18 false 5, 7

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 WHEN REPLACING BATTERY ECU ASSEMBLY - (Click here) - -
3 SERVICE PLUG GRIP G3834 - - -
4 DISCONNECT ENGINE WIRE 82121 (Click here) - -
5 REMOVE CONNECTOR COVER ASSEMBLY - (Click here) - -
6 TERMINAL VOLTAGE - (Click here) - -
7 INSTALL CONNECTOR COVER ASSEMBLY - (Click here) - -
8 CONNECT ENGINE WIRE 82121 (Click here) - -

A461204N04
1.354,1.344 2.875,1.344 false 2.719,2.125 2.719,1.344 false 5.385,0.688 5.75,0.688 false 5.302,1.677 5.938,1.677 false 2.615,4.156 3.042,4.156 false 6.115,3.948 6.542,3.948 false 3.156,1.208 3.708,1.563 0.552,0.354 18 false 11 5.833,0.5 6.385,0.854 0.552,0.354 18 false 9 6.104,1.531 6.656,1.885 0.552,0.354 18 false 10 6.604,3.771 7.156,4.125 0.552,0.354 18 false 13 3.104,4 3.656,4.354 0.552,0.354 18 false 12 6.135,3.438 6.375,3.635 0.24,0.198 10 false x6 2.99,1.271 3.354,1.5 0.365,0.229 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

9 REAR CENTER SEAT OUTER BELT ASSEMBLY 73350C - - -
10 BENCH TYPE REAR SEAT CUSHION ASSEMBLY - - - -
12 REAR SEAT CUSHION LOCK HOOK 72693 - - -
12 REAR UNDER COVER 76971G - - -
13 REAR SEAT CUSHION LEG SUB-ASSEMBLY 71033 - - -

● Non-reusable part - -

A478807N01
1.542,1.219 1.938,1.219 false 1.646,2.354 2.042,2.354 false 5.781,1.813 6.063,1.813 false 6.271,2.448 6.167,3.042 6.167,3.042 6.063,3.042 false 5.229,4.26 5.51,4.26 false 1.229,1.031 1.604,1.344 0.375,0.313 18 false 16 2.094,2.188 2.469,2.5 0.375,0.313 18 false 15 6.385,1.677 6.76,1.99 0.375,0.313 18 false 14 5.438,1.865 5.813,2.177 0.375,0.313 10 false x5 5.781,2.833 6.156,3.146 0.375,0.313 18 false 14 5.781,4.135 6.156,4.448 0.375,0.313 18 false 17

Procedure Part Name Code
Z101186

Z101188

Z101187

14 HV BATTERY UPPER COVER PANEL G92N1 (Click here) - -
15 HYBRID BATTERY HOSE ASSEMBLY G9290A - - -
16 HV FLOOR UNDER WIRE 821H1 (Click here) - -
17 FLOOR WIRE 821H3 (Click here) - -

A461206N03
5.552,1.167 5.792,1.167 false 2.573,1.115 2.521,1.594 2.521,1.594 2.396,1.594 false 2.271,2.729 2.271,2.5 false 6.135,1 6.688,1.354 0.552,0.354 18 false 18 2.083,1.427 2.635,1.781 0.552,0.354 18 false 19 2.344,2.76 2.896,3.115 0.552,0.354 18 false 20 3.427,1.323 3.979,1.677 0.552,0.354 10 false x6 4.969,0.354 5.521,0.708 0.552,0.354 10 false x4 2.115,1.969 2.667,2.323 0.552,0.354 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

18 UPPER HV BATTERY COVER SUB-ASSEMBLY - (Click here) - -
19 NO. 1 HV BATTERY HOSE G929A (Click here) - -
20 BATTERY ECU ASSEMBLY 89890A (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of battery ECU assembly Current sensor offset learning DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

The type of battery ECU assembly to be used varies depending on the vehicle model.

·

The type of battery ECU assembly to be used varies depending on the vehicle model.

·

If the wrong type of battery ECU assembly is installed, the ignition switch cannot be turned on (READY).

·

After installing the battery ECU assembly, perform the following to check that the ignition switch can be turned on (READY).

-

Turn the ignition switch to ON (READY).

-

Turn the ignition switch off and wait for 30 seconds or more.

-

Turn the ignition switch on (READY) again.




HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. WHEN REPLACING BATTERY ECU ASSEMBLY

HV battery learning values are stored in the battery ECU assembly and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

Z101186

NOTICE:
·

Do not replace the battery ECU assembly and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the battery ECU assembly or ECM with a used one from another vehicle.




a.
A460058N01
0.427,0.063 0.708,0.417 0.281,0.354 18 false i

i.

Procedure when replacing both battery ECU assembly and ECM:

1. Disconnect the cable from the negative (-) auxiliary battery terminal.

2. Replace either ECU.

3. Connect the cable to the negative (-) auxiliary battery terminal.

4. Turn the ignition switch on (READY) and wait for 5 minutes or more.

5. Turn the ignition switch off and disconnect the cable from the negative (-) auxiliary battery terminal.

6. Replace the other ECU.

7. Connect the cable to the negative (-) auxiliary battery terminal.

8. Check that the ignition switch can be turned on (READY).

HINT:

If the battery ECU assembly and ECM are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 82121 4.DISCONNECT ENGINE WIRE

Z101186

Click here(Click here)

Hide 5.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 6.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 7.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 82121 8.CONNECT ENGINE WIRE

Z101186

Click here(Click here)

Hide 73350C 9.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 11.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 76971G 12.REMOVE REAR UNDER COVER

Hide 71033 13.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N1 14.REMOVE HV BATTERY UPPER COVER PANEL

Z101186

Click here(Click here)

Hide G9290A 15.REMOVE HYBRID BATTERY HOSE ASSEMBLY

Hide 821H1 16.DISCONNECT HV FLOOR UNDER WIRE

Z101186

Click here(Click here)

Hide 82161 17.DISCONNECT FLOOR WIRE

Z101186

Click here(Click here)

Hide 18.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A458360C01
3.344,0.052 3.552,0.24 0.208,0.188 10 true *a 3.74,0.052 3.948,0.24 0.208,0.188 10 true *a 4.688,1.156 4.896,1.344 0.208,0.188 10 true *a 2.281,0.854 2.49,1.042 0.208,0.188 10 true *a 4.125,0.146 4.333,0.333 0.208,0.188 10 true *b 2.49,0.115 2.698,0.302 0.208,0.188 10 true *b 4.438,1.552 4.646,1.74 0.208,0.188 10 true *b 3.844,1.542 4.052,1.729 0.208,0.188 10 true *b 3.135,1.552 3.344,1.74 0.208,0.188 10 true *b 2.625,1.438 2.833,1.625 0.208,0.188 10 true *b
*a Bolt *b Nut



Hide G929A 19.REMOVE NO. 1 HV BATTERY HOSE

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A459147


Hide 89890A 20.REMOVE BATTERY ECU ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A459150N01
2.229,0.104 2.427,0.396 0.198,0.292 18 true i

i.

Move the lock lever while pushing the lock on the connector, and disconnect the 3 battery ECU assembly connectors.

NOTICE:
A393180C04
1.51,2.76 1.708,2.76 1.708,2.76 2.021,2.385 true 1.333,2.688 1.646,2.885 0.313,0.198 10 false *a
*a Lock Lever


Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.




b.
A459812N01
2.219,0.094 2.438,0.396 0.219,0.302 18 true i

i.

Remove the 3 nuts and battery ECU assembly from the HV battery.

NOTICE:

If the battery ECU assembly has been struck or dropped, replace it.