The battery ECU assembly alerts the driver and performs fail-safe control based on malfunction signals.
If the HV battery is discharged excessively or the hybrid battery system is malfunctioning, this DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P300016 | Hybrid/EV Battery Control System Circuit Voltage Below Threshold | Either of the following conditions is met:
A malfunction signal is received from the battery ECU assembly. The voltage of any HV battery cell has decreased excessively. (1 trip detection logic) |
·
SFI system ·
Hybrid vehicle transaxle assembly ·
HV battery state of charge |
Does not come on | Master Warning:
Comes on |
HV Battery | A |
If the HV battery voltage has dropped due to a malfunction in other components, such as the hybrid motor control inverter assembly or the hybrid vehicle transaxle assembly, recharging the HV battery will be able to restore the voltage. If the HV battery voltage has dropped excessively after the vehicle was left for a long time, the HV battery will need to be replaced.
| DTC No. | Data List |
|---|---|
| P300016 | ·
Hybrid/EV Battery Cell 1 to 48 Voltage ·
Hybrid/EV Battery Cell 1 to 48 Internal Resistance ·
Hybrid/EV Battery SOC ·
Hybrid/EV Battery Voltage ·
Hybrid/EV Battery Current ·
Engine Speed |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY) with park (P) selected.
Wait until the engine starts and then stops.
Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Thoroughly interview the customer as DTC P300016 may be stored if the SOC drops due to the vehicle being left with neutral (N) selected for a long time or running out of fuel.
When the engine cannot be started, DTC P300016 may be stored because the HV battery cannot be charged.
If differences among SOCs of HV battery exceed the specifications, the master warning may illuminate when "Battery Diagnosis" is complete. In this case, check for hybrid system related DTCs. If DTC P300016 is output, leave the vehicle with the ignition switch to ON (READY) for 10 minutes or more allowing the vehicle to charge the HV battery. Then clear the DTCs.
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P300000 or P300016 is output | A |
| P300000 or P300016 and other DTCs are output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Turn the ignition switch to ON (READY).
Procedure1
Check if the engine starts.
Do not turn the ignition switch to ON (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.
Depressing the accelerator pedal with park (P) selected will cause the engine to start.
| Result | Proceed to |
|---|---|
| The engine does not start. | A |
| The engine starts. | B |
Post-procedure1
Turn the ignition switch off.
A
B
Pre-procedure1
Make sure that the shift lever is in P position.
Lift up the vehicle.
Procedure1
Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.
Do not turn the ignition switch to ON (READY) while performing this inspection. Be sure to turn the ignition switch off before performing this inspection, to prevent the engine from starting.
Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.
| Result | Proceed to |
|---|---|
| The crankshaft rotates smoothly. | A |
| The crankshaft does not rotate smoothly. | B |
Post-procedure1
Lower the vehicle.
A
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>CHARGING
As the HV battery is not malfunctioning, it is necessary to charge the HV battery with the THS charger.
B
Pre-procedure1
Lift up the vehicle.
Move the shift lever to N.
Procedure1
Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.
Do not turn the ignition switch to ON (READY) while performing this inspection. Be sure to turn the ignition switch off before performing this inspection, to prevent the engine from starting.
Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.
| Result | Proceed to |
|---|---|
| The crankshaft does not rotate smoothly. | A |
| The crankshaft rotates smoothly. | B |
Post-procedure1
Move the shift lever to P.
Lower the vehicle.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON (READY).
Procedure1
Check if the engine starts.
Do not turn the ignition switch to ON (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.
Depressing the accelerator pedal with park (P) selected will cause the engine to start.
| Result | Proceed to |
|---|---|
| The engine does not start. | A |
| The engine starts. | B |
Post-procedure1
Turn the ignition switch off.
A
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>CHARGING
As the HV battery is not malfunctioning, it is necessary to charge the HV battery with the THS charger.
B
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON (READY).
Procedure1
Check if the engine starts.
Do not turn the ignition switch to ON (READY) repeatedly after duplicating the problem symptom indicated by DTC P300016 and clearing the DTCs. This may cause another problem to occur.
Depressing the accelerator pedal with park (P) selected will cause the engine to start.
| Result | Proceed to |
|---|---|
| The engine does not start. | A |
| The engine starts. | B |
Post-procedure1
Turn the ignition switch off.
A
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>CHARGING
As the HV battery is not malfunctioning, it is necessary to charge the HV battery with the THS charger.
B