| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 10 | ENGINE ASSEMBLY | - | ( )
|
- | - |
| 11 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | 51201 | - | - | - |
| 12 | NO. 2 ENGINE MOVING CONTROL ROD | 12364B | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 13 | CONNECTOR COVER | 82821T | ( )
|
- | - |
| 14 | TERMINAL CAP | 82823M | ( )
|
- | - |
| 15 | MOTOR CABLE | G1148 | ( )
|
- | - |
| 16 | MOTOR COOLING COOLER | G125A | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | ★ | Precoated part |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during hybrid vehicle transaxle assembly removal/installation are shown below.
This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.
Be sure to wear insulating gloves when working on high voltage wiring or components.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PERFORM RESOLVER INITIALIZATION
2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
3.INSTALL ENGINE HANGERS
82121
4.DISCONNECT ENGINE WIRE
Disengage the 6 clamps.
Disengage the clamp.
Remove the bolt.
Disconnect the shift lever position sensor connector.
After disconnecting the engine wire, cover the connector of the shift lever position sensor with tape (non-residue type) or equivalent to prevent the entry of foreign matter or water.
Disconnect the generator temperature sensor connector.
Disconnect the resolver (transmission fluid temperature sensor) connector.
821H2
5.REMOVE HV AIR CONDITIONING WIRE
| *a | Green-colored Lock | - | - |
|
Slide | - | - |
Remove the 2 bolts to disconnect the HV air conditioning wire from the hybrid vehicle transaxle assembly.
Disengage the clamp.
Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.
Make sure to wear insulated gloves.
Insulate the disconnected terminals and connector with insulating tape.
28193
6.REMOVE STARTER HOLE INSULATOR
11363A
7.REMOVE FLYWHEEL HOUSING SIDE COVER
16290F
8.SEPARATE NO. 3 WATER BY-PASS HOSE ASSEMBLY
43409E
9.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
10.REMOVE ENGINE ASSEMBLY
|
|
51201
11.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
12364B
12.REMOVE NO. 2 ENGINE MOVING CONTROL ROD
G125A
16.REMOVE MOTOR COOLING COOLER
Slide the clip and disconnect the No. 1 motor cooling hose from the No. 1 motor cooling pipe.
Remove the oil cooler union bolt and gasket to disconnect the No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.
Disengage the clamp.
Remove the 3 bolts and motor cooling cooler with No. 2 motor cooling pipe from the hybrid vehicle transaxle assembly.
Make sure not to remove the No. 1 motor cooling hose and No. 2 motor cooling hose from the motor cooling cooler as the motor cooling cooler may be deformed.
G1251B
17.SEPARATE NO. 1 MOTOR COOLING PIPE
32924E
18.REMOVE NO. 2 OIL COOLER TUBE CLAMP
44781E
19.REMOVE HOSE BRACKET
33823
20.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
21.REMOVE WIRE HARNESS CLAMP BRACKET
22.REMOVE STUD BOLT
Using a E8 "TORX" socket wrench, remove the 2 stud bolts from the hybrid vehicle transaxle assembly.
23.REMOVE TRANSAXLE HOUSING PLUG
|
|
30900N
24.REMOVE TRANSAXLE BREATHER PLUG
|
|
25.REMOVE UNION
|
|