Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2020.08–2021.07
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0438366 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B235787  Wiper Module Missing Message  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper relay assembly communicate via CXPI communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B235787 Wiper Module Missing Message
Detection condition:

Auxiliary battery voltage is 9.5 V or more


Malfunction Status:

Communication malfunction between the main body ECU (multiplex network body ECU) and windshield wiper relay assembly


Malfunction Time:

10 seconds or more


·

Windshield wiper relay assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

WIPER relay

·

Power distribution box assembly


○ Main Body A

WIRING DIAGRAM

E434515E07
2.958,1.802 3.448,2.146 0.49,0.344 10 false WIPER 0.479,4.49 1.604,4.885 1.125,0.396 10 false Windshield Wiper Relay Assembly 5.417,3.698 7.094,4.188 1.677,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 0.833,5.302 2.51,5.573 1.677,0.271 10 false : CXPI Communication Line 1.719,0.969 2.177,1.167 0.458,0.198 10 false A50 1.719,3.438 2.177,3.635 0.458,0.198 10 false A50 1.708,2.823 2.167,3.021 0.458,0.198 11 false A49 1.719,4.021 2.177,4.219 0.458,0.198 10 false A49 1.813,0.781 1.969,0.979 0.156,0.198 10 false 8 1.813,2.635 1.969,2.833 0.156,0.198 10 false 4 1.802,3.24 1.958,3.438 0.156,0.198 10 false 3 1.802,3.823 1.958,4.021 0.156,0.198 10 false 5 3.969,1.135 4.583,1.344 0.615,0.208 10 false WIPER 2.979,0.208 4.74,0.594 1.76,0.385 10 false from Auxiliary Battery 5.188,1.438 5.646,1.635 0.458,0.198 10 false H4 5.167,2.833 5.625,3.031 0.458,0.198 10 false MB 5.229,1.25 5.542,1.448 0.313,0.198 10 false 6 3.344,2.646 3.5,2.844 0.156,0.198 10 false 5 5.531,1.344 5.99,1.542 0.458,0.198 10 false WPS 5.521,2.844 6.135,3.042 0.615,0.198 10 false CXPI 1.406,0.99 1.719,1.188 0.313,0.198 10 false +B 1.229,2.854 1.844,3.052 0.615,0.198 10 false MPX1 1.479,3.469 1.635,3.667 0.156,0.198 10 false E 1.406,4.031 1.719,4.229 0.313,0.198 10 false ES 2.729,0.885 2.969,1.104 0.24,0.219 10 false 5 2.729,1.344 2.885,1.542 0.156,0.198 10 false 2 3.563,0.875 3.719,1.073 0.156,0.198 10 false 3 3.563,1.344 3.719,1.542 0.156,0.198 10 false 1 3.292,2.833 3.75,3.031 0.458,0.198 10 false 4D 5.188,2.635 5.385,2.854 0.198,0.219 10 false 22 3.635,3.385 5.063,3.875 1.427,0.49 10 false Power Distribution Box Assembly 6.135,0.823 6.448,1.021 0.313,0.198 10 false IG 6.49,0.823 6.646,1.021 0.156,0.198 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

*1: w/ Entry and Start System




HINT:

The wiper and washer system uses the CXPI communication system. First, confirm that there is no malfunction in the CXPI communication system.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - POWER DISTRIBUTION BOX ASSEMBLY)

Pre-procedure1

a.

Disconnect the A49 windshield wiper relay assembly connector.


b.

Disconnect the 4D power distribution box assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A49)Location & Routing

Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

A49-4 (MPX1) - 4D-5 Always Below 1 Ω
A49-4 (MPX1) or 4D-5 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

2.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

Pre-procedure1

a.

Disconnect the 4D power distribution box assembly connector.


b.

Disconnect the MB main body ECU (multiplex network body ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-5 - MB-22 (CXPI) Always Below 1 Ω
4D-5 or MB-22 (CXPI) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Pre-procedure1

a.

Connect the 4D power distribution box assembly connector


Procedure1

b.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A49)Location & Routing

Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

A49-4 (MPX1) - Body ground Ignition switch ON Pulse generation
A49-4 (MPX1) - Body ground Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.PERFORM ACTIVE TEST USING GTS (WIPER POWER RELAY)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.PERFORM ACTIVE TEST USING GTS (WIPER POWER RELAY)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wiper Power Relay Function to operate the IG1 wiper relay OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Wiper Power Relay
50004 449 70
OK:

IG1 WIP relay operates normally.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

NG

10.INSPECT WIPER RELAY
5.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the A50 and A49 windshield wiper relay assembly connectors.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A50,A49)Location & Routing

Click Connector(A50)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

A50-3 (E) - Body ground Always Below 1 Ω
A49-5 (ES) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER RELAY ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A50)Location & Routing

Click Connector(A50)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

A50-8 (+B) - Body ground Ignition switch ON 11 to 14 V
A50-8 (+B) - Body ground Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
A50-8 (+B) - Body ground Approximately 60 seconds or more after ignition switch turned off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

7.INSPECT WIPER RELAY
7.INSPECT WIPER RELAY

OK

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WIPER RELAY)

NG

REPLACE WIPER RELAY

8.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WIPER RELAY)
a.
E409904C09
0.51,0.885 0.938,1.083 false 0.333,0.781 0.646,0.938 0.313,0.156 10 false *a 0.115,0.063 0.427,0.26 0.313,0.198 10 false *1
*1 No. 1 Engine Room Relay Block
*a WIPER Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
WIPER relay holder terminal 3 - Body ground Ignition OFF 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WIPER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WIPER RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A50)Location & Routing

Click Connector(A50)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

A50-8 (+B) - WIPER relay holder terminal 5 Always Below 1 Ω
A50-8 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT WIPER RELAY

OK

11.CHECK HARNESS AND CONNECTOR (WIPER RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE WIPER RELAY

11.CHECK HARNESS AND CONNECTOR (WIPER RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

Pre-procedure1

a.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H4)Location & Routing

Click Connector(H4)Instrument Panel>Instrument Panel Wire / Speaker Wire>Main Body ECU

WIPER relay holder terminal 1 - H4-6 (WPS) Always Below 1 Ω
WIPER relay holder terminal 1 or H4-6 (WPS) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

12.CHECK HARNESS AND CONNECTOR (BODY GROUND - WIPER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (BODY GROUND - WIPER RELAY)
a.
E409904C09
0.51,0.885 0.938,1.083 false 0.333,0.781 0.646,0.938 0.313,0.156 10 false *a 0.115,0.063 0.427,0.26 0.313,0.198 10 false *1
*1 No. 1 Engine Room Relay Block
*a WIPER Relay Holder


Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
WIPER relay holder terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR