Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › 2020.08–2021.07
RM3700E _57 Power Source / Network _093028 POWER DISTRIBUTION _0438533 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E448338N02
6.438,0.219 6.854,0.219 false 6.125,4.865 6.125,5.198 false 6.406,0.615 6.823,0.615 false 6.042,2.5 6.458,2.5 false 6.354,1.281 6.771,1.281 false 3.833,0.781 4.25,0.781 false 6.042,3.302 6.458,3.302 false 1.771,5.271 2.188,5.271 false 0.698,4.302 1.115,4.302 false 0.375,1.469 0.792,1.469 false 1.344,2.656 1.76,2.656 false 3.906,4.792 3.906,5.125 false 3.625,3.604 3.625,3.938 false 3,2.271 3,2.604 false 4.26,2.26 4.573,2.458 0.313,0.198 10 false x2 4.552,2.104 4.865,2.302 0.313,0.198 10 false x3 6.271,0.073 6.552,0.427 0.281,0.354 18 false 1 6.24,0.469 6.521,0.823 0.281,0.354 18 false 2 6.5,2.375 6.781,2.729 0.281,0.354 18 false 3 6.823,1.135 7.104,1.49 0.281,0.354 18 false 4 4.302,0.656 4.583,1.01 0.281,0.354 18 false 5 6.521,3.167 6.802,3.521 0.281,0.354 18 false 6 6.073,5.229 6.354,5.583 0.281,0.354 18 false 7 1.594,5.135 1.875,5.49 0.281,0.354 18 false 8 0.521,4.156 0.802,4.51 0.281,0.354 18 false 9 0.844,1.333 1.219,1.719 0.375,0.385 18 false 10 1.781,2.521 2.156,2.906 0.375,0.385 18 false 11 3.781,5.146 4.156,5.531 0.375,0.385 18 false 12 3.51,3.948 3.885,4.333 0.375,0.385 18 false 13 2.875,2.615 3.25,3 0.375,0.385 18 false 14

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH 55475B - - -
4 INSTRUMENT PANEL FINISH PANEL 55431A - - -
5 LOWER INSTRUMENT PANEL FINISH PANEL 55432B - - -
6 SWITCH HOLE BASE SUB-ASSEMBLY 55407B - - -
7 CONSOLE BOX ASSEMBLY 58810J - - -
8 FRONT DOOR SCUFF PLATE LH 67914B - - -
9 COWL SIDE TRIM BOARD LH 62112 - - -
10 FRONT DOOR OPENING TRIM WEATHERSTRIP LH 62312B - - -
11 NO. 2 INSTRUMENT SIDE PANEL 55318F - - -
12 NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55607 - - -
13 GLOVE COMPARTMENT DOOR ASSEMBLY 55550 - - -
14 LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL 55433B - - -

E448339N01
3.865,1.656 6.417,2.667 2.552,1.01 6.031,3.25 6.5,3.25 false 4.354,2.458 4.594,2.458 false 3,1.417 3.167,1.417 false 2.75,2 3,1.417 false 5.635,2.292 5.958,2.292 false 3.448,1.292 3.875,1.573 0.427,0.281 18 false 15 3.438,2.125 3.667,2.281 0.229,0.156 10 false x2 3.167,2.885 3.479,3.083 0.313,0.198 10 false x2 4.625,2.323 4.938,2.583 0.313,0.26 18 false 16 5.729,3.115 6.281,3.469 0.552,0.354 18 false 17 5.469,2.24 5.781,2.438 0.313,0.198 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

15 POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU - (Click here) - -
16 POWER DISTRIBUTION BOX ASSEMBLY 82730G - - -
17 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 89221 (Click here) - -

*1 ECU INTEGRATION BOX LH - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
for HV Model:
Main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.
for Gasoline Model:
Main body ECU (multiplex network body ECU)
Code registration
·

Wireless door lock control system (w/ Entry and Start System)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 55475B 3.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55431A 4.REMOVE INSTRUMENT PANEL FINISH PANEL

Hide 55432B 5.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55407B 6.REMOVE SWITCH HOLE BASE SUB-ASSEMBLY

Hide 58810J 7.REMOVE CONSOLE BOX ASSEMBLY

Hide 67914B 8.REMOVE FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62112 9.REMOVE COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure as for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62312B 10.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55318F 11.REMOVE NO. 2 INSTRUMENT SIDE PANEL

HINT:

Use the same procedure as for the No. 1 side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55607 12.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 13.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55433B 14.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 15.REMOVE POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

a.
E449725C01
2.167,0.083 2.448,0.438 0.281,0.354 18 false i

i.

Disengage the clamps.



b.
E448341C02
3.875,0.615 4,0.469 false 4.271,1.438 4.438,1.219 false 0.698,0.375 1.25,0.729 0.552,0.354 18 false i 2.552,0.177 2.76,0.458 0.208,0.281 18 true ii 5.073,0.198 5.302,0.406 0.229,0.208 12 true *A 5.542,0.177 5.75,0.469 0.208,0.292 18 true iii 0.708,2.083 1.26,2.438 0.552,0.354 18 false i 4.063,2.438 4.271,2.75 0.208,0.313 18 true i 3.75,0.615 4.063,0.813 0.313,0.198 10 false *a 4.469,1.104 4.781,1.302 0.313,0.198 10 false *a 4.083,2.771 4.292,3.083 0.208,0.313 18 true i
*A for HV Model - -
*a Lock Lever - -


i.

Disconnect the each connector.


ii.

Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


iii.

for HV Model:

1. Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.



c.
E448342N01
2.573,0.083 2.771,0.385 0.198,0.302 18 true i 1.583,0.052 1.719,0.323 0.135,0.271 18 true i 2.823,1.448 3.021,1.75 0.198,0.302 18 true i 0.688,0.177 0.885,0.479 0.198,0.302 18 false ii 4.271,0.063 4.469,0.365 0.198,0.302 18 false iii

i.

Remove the bolt and 2 nuts.


ii.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws.


iii.

Disengage the claws.



d.
E448343C02
2.281,0.719 2.5,0.458 false 2.313,1.229 2.719,1.208 true 2.198,0.063 2.479,0.417 0.281,0.354 18 false i 3.302,0.198 3.531,0.49 0.229,0.292 18 true ii 2.156,0.719 2.469,0.917 0.313,0.198 10 false *a 2.125,1.167 2.438,1.365 0.313,0.198 10 false *a
*a Lock Lever - -


i.

Disengage the claws and pull up the lock levers to disconnect the 2 connectors as shown in the illustration.


ii.

Remove the power distribution box assembly with multiplex network body ECU.



Hide 82730G 16.REMOVE POWER DISTRIBUTION BOX ASSEMBLY

a.
E437138


Hide 89221 17.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E448344C01
0.604,1.052 0.99,1.052 true 1.104,1.115 1.323,1.344 true 0.417,0.99 0.729,1.188 0.313,0.198 10 false *2 1.385,1.271 1.698,1.469 0.313,0.198 10 false *1 1.75,0.167 2,0.531 0.25,0.365 18 false i 6.469,1.406 6.667,1.708 0.198,0.302 18 false ii 2.469,2.323 2.719,2.688 0.25,0.365 18 false iv 5.521,0.073 5.792,0.333 0.271,0.26 18 false iii
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)
V100135

Push
V100136

Insert
V100137

Raise
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2) - -


i.

Press the claw of the power distribution box assembly as shown in the illustration to release the lock.


ii.

With the power distribution box assembly lock released, insert a screwdriver with its tip wrapped in protective tape horizontally between the main body ECU (multiplex network body ECU) and the power distribution box assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).




iii.

Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).



iv.

Remove the main body ECU (multiplex network body ECU) as shown in the illustration.

NOTICE:

Do not touch the main body ECU (multiplex network body ECU) connector.