These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly or headup display (meter mirror sub-assembly)* is not possible.
*: w/ Headup Display System
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B1324 | Lost Communication with Meter | CAN reception error | ·
Local bus communication line ·
Combination meter power source circuit ·
Combination meter assembly ·
Radio and display receiver assembly ·
Harness or connector ·
No. 4 global can junction connector |
Navigation System | A |
| B1325 | Lost Communication with HUD | CAN reception error | ·
Local bus communication line ·
Headup display (meter mirror sub-assembly) power source circuit ·
Headup display (meter mirror sub-assembly) ·
Radio and display receiver assembly ·
Harness or connector ·
No. 4 global can junction connector |
Navigation System | A |
The radio and display receiver assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| B1324 and B1325 are not output | A |
| B1324 and B1325 are output | B |
| B1324 is output | C |
| B1325 is output | D |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Below 54 Ω) | B |
| NG (70 Ω or higher) | C |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=11,22 |
||
| H115-11 - H115-22 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=9,20 |
||
| H115-9 - H115-20 | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=14,15 |
||
| H61-14 (TX+) - H61-15 (TX-) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Connect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=27,10 |
||
| H6-27 (MSCH) - H6-10 (MSCL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H80 radio and display receiver assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Post-procedure1
OK
NG
Pre-procedure1
Disconnect the H6 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=23 |
||
| H6-23 (ES) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=22,38 |
||
| H6-22 (B) - Body ground | Ignition switch off | 11 to 14 V |
| H6-38 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H6 combination meter assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=11,22 |
||
| H115-11 - H115-22 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H6 combination meter assembly connector.
Connect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H6)Location & Routingewd_type=routing;type=c;code=H6 Click Connector(H6)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assemblyewd_type=component;type=c;code=H6;pinno=27,10 |
||
| H6-27 (MSCH) - H6-10 (MSCL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=4 |
||
| H61-4 (ES) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=2,1 |
||
| H61-2 (B) - Body ground | Ignition switch off | 11 to 14 V |
| H61-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Connect the H61 headup display (meter mirror sub-assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=9,20 |
||
| H115-9 - H115-20 | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H115)Location & Routingewd_type=routing;type=c;code=H115 Click Connector(H115)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 4 Global CAN Junction Connectorewd_type=component;type=c;code=H115;pinno=10,21 |
||
| H115-10 - H115-21 | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H80 radio and display receiver assembly connector.
Connect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=5,6 |
||
| H80-5 (CNH1) - H80-6 (CNL1) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H61 headup display (meter mirror sub-assembly) connector.
Connect the H115 No. 4 global can junction connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H61)Location & Routingewd_type=routing;type=c;code=H61 Click Connector(H61)Instrument Panel>Instrument Panel Wire / Speaker Wire>Meter Mirror Sub-Assemblyewd_type=component;type=c;code=H61;pinno=14,15 |
||
| H61-14 (TX+) - H61-15 (TX-) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG